EMART VL 60BI Mobile Phone LED Light User Manual

EMART VL 60BI Mobile Phone LED Light

Safety tips:

For your correct use of this product. please read the following safety precaution before operation and keep the manual for all users’ looking up anytime. Before operating this unit, please read the instruction carefully and properly keep.for future reference.

Product structure Introduction

1. The lamp panel
2. Angle adjustment knob
3. Before the clip
4. The back clip fixed screw holes 5
5. Lens fixing hole
6. The power/mode switch button
7.  Increasing brightness buttons 8
8. Brightness decline button 9
9. Micro – USS charging interface
10. The Type-C charging interface
11. The power indicator light
12. The back clip
13. Before the clamp fixed card buckle

Characteristic

This product is a new designed LED light for mobile phone use which is super slim with small size and using simple. It is made of highlight 2835 LED beads (30pcs 3200K and 30pcs 5600K). Using lamp shade makes the light illumination more soft. 10 levels brightness controlling and 3 lightning models containing pure white, warm white, double-colors satisfy different environmental needs. This light is equiped with front clip and back clip. When using front clip, adjusting the angle knob can make the light rotated front and back in 90° the mobile phone lens can be also fixed on the front clip. This light can be fixed at the back side of mobile phone with back clip in order to supplement the lightning. High efficient drive circuit and constant current/constant voltage output make every LED bead perform much better, built-in 2000mAh polymer battery cells offers 2 hours continuous lightning. Equipped with micro-USB and Type-C charging input makes the charging more convenient.

Cleaning notes

1. Clean the dirt in video light with detergent and make it dry with soft cloth.
2. Don’t use strong detergents. Such as thinner, gasoline and alcohol. Which could damage the protective layer.

Product installation and use

Product installation

1. Take out the main body, the former as the fill light clip, clip before fixed card buckle end is inserted into the main body of a fixed slot. hear cut after. before the installation is complete
2. Put the fill light before the clip on the mobile phone is used to fill light. If you have cell phone camera. mobile phone lens can be clockwise lens fixed hole before screwing in. Then before and lens holder to the mobile phone, camera position, and can be used at the same time and lens as the fill light
3. Unscrew the angle adjusting knob counter clockwise. will adjust to the appropriate angle as the fill light. then tighten the Angle adjusting knob clockwise and Angle adjustment to complete at this time
4. Press clamp fixed card buckle before. and then go toward outside. can be removed before the clip.
5. Remove the back clip, clip back three torque of one side and on the back of the body as the fill light on one side of the groove, and then under the hard back, this time three torque will buckle to main body as the fill light three grooves, the back clip installation is complete
6. Use the back clip will be fixed as the fill light in the back of the phone, can be used in the mobile phone when the rear camera to the rear light
7. If you want to remove the back clip. just put the jacket has two buckle outward pull on one side, and then. on the back clip can be removed

Front and back clip to use

1. When installation, to push the bracket alignment slot is stuck.
2. Remove, will stretch button press stretching back off.

1. When installation, aim the clip one foot back and feet fuselage card slot stretching back stuck.
2. When installation, stretching back c1ip in the direction shown by the arrow in the cell phone.
3. Remove, tensile mobile phones under the back clip in the direction shown by the arrow.
4. Remove, down the stretch in the direction shown by the arrow.

Charging
Will the charger plug, and then use a USB to Micro USB or Type -C power cord, connect the charger with the fill light. the power supply will stream lights flashing, said it was charging, when the lights are no longer flashing, the charging process is complete.

Function and display

1. Switch machine
2. Long press the power/mode button for 3 seconds. boot. as the fill light is color by default
3. Again. long press the power/mode button for 3 seconds. turn it oft as the fill light
4. The mode switch
5. Short press the power/mode button. by double color mode switch to warm color as the fill light
6. Short press the power/mode button by the warm color patterns as the fill light switch for the cool color mode
7. Short press the power/mode button again. will switch to a double color patterns as the fill light
8. Brightness control
   In any mode. per click the brightness buttons + brightness increased by 10%. the maximum 100%. Per click the brightness lower keys – . brightness to reduce 10%, minimum 10%

Product Dimensions

• Einheit mm
• Tolerances: ± 1.0mm
• L,d04
• W=75
• H:11.8

Technical Parameter

Notes:

1. The video light dust proof, waterproof function.
2. The video light belongs to precision instruments, please do not make lambency lamp fell to the ground, collision or a strong shock.
3. The working temperature of the video light of O “C- 40 “C.
4. Please do not covering vents, otherwise may make internal temperature rise and cause a fire or accident. video light caused by accident.
5. Do not use close look of the w hite LED, otherwise may be visually impaired.
6. Do not use the video light placed near combustible or easily play solvent, oth erwise may send and receive fire or smoke.
7. The completed with the times as the fill light w ill switch to “OFF” to shut down.
8. Do not use in the video light after into storage box, waste heat may take a toll on the white LED. To light the lamp after cooled sufficiently to put in storage box.

Specifications and design are subject to change without notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>