Vantron UCTTA-42 Rockchip ARM Cortex A17 RK3288 with Quad ARM Cortex A17 User Manual

Vantron UCTTA-42 Rockchip ARM Cortex A17 RK3288 with Quad ARM Cortex A17

Foreword

Copyright Notice

While all information contained herein have been carefully checked to assure its accuracy in technical details and printing, Ventnor assumes no responsibility resulting from any error or features of this manual, or from improper uses of this manual or the software. Please contact our technical department for relevant operation solutions if there is any problem that cannot be solved according to this manual.
Ventnor reserves all rights of this manual, including the right to change the content, form, product features, and specifications contained herein at any time without prior notice. The latest version of this manual is at www.vantrontech.com.cn. Please contact Dantron for further information:

Ventnor Technology（Vantron）

E-mail:sales@vantrontech.com

The trademarks and registered trademarks in this manual are properties of their respective owners. No part of this manual may be copied, reproduced, translated or sold. No changes or other purposes are permitted without the prior written consent of Ventnor. Ventnor reserves the right of all publicly- released copies of this manual.

Notes

Applicable notes are listed in the following table:

Sign

| Notice Type|

Description

---|---|---
| Notice| Important information and regulations
| Caution| Caution for latent damage to system or

harm to personnel

Statement

It is recommended to read and comply with this manual before operating board, which provides important guidance and helps decreasing the danger of injury, electric shock, fire, or any damage to the device

Disclaimer

Ventnor assumes no legal liability of accidents resulting from failure of conforming to the safety instructions.

Limitation of Liability/Non-warranty

For direct or indirect damage to this device or other devices of Ventnor caused by failure of conforming to this manual or the safety instructions on device label, Ventnor assumes neither warranty nor legal liability even if the device is still under warranty.

Safety Instructions

• Keep and comply with all operation instructions, warnings, and information.
• Pay attention to warnings on this device.
• Read the following precautions so as to decrease the danger of injury, electric shock, fire, or any damage to the device.

Precautions

• Pay attention to the product labels/safety instructions printed on silk screens.
• Do not try repairing this product unless declared in this manual.
• Keep away from heat source, such as heater, heat dissipater, or engine casing.
• Do not insert other items into the slot (if any) of this device.
• Keep the ventilation slot ventilated for cooling.
• System fault may arise if other items are inserted into this device.
• Installation: ensure correct installation according to instructions from the manufacturer with recommended installation tools.
• Ensure ventilation and smoothness according to relevant ventilation standard.

Safety Instructions for Power Cables and Accessories

Proper power source only
Start only with power source that satisfies voltage label and the voltage necessary according to this manual. Please contact technical support personnel of Ventnor for any uncertainty about the requirements of necessary power source.

Warning：

• This battery cannot mix with deposal or twice- recycled batteries in use. Otherwise, for its abnormal charge and discharge, it will cause over-heated, distort, smoke or burning.

Use tested power source
This product still contains a button lithium battery as a real-time clock after its external power source is removed and therefore should not be short- circuited during transportation or placed under high temperature.

Place cables properly:
Do not place cables at any place with extrusion danger.

Cleaning Instructions

• Please power off before cleaning the device.
• Do not use spray detergent.
• Clean with a damp cloth.
• Do not try cleaning exposed electronic components unless with a dust collector.
• Support for special fault: Power off and contact technical support personnel of Ventnor in case of the following faults:
  • The device is damaged.
  • The temperature is excessively high.
  • Fault is still not solved after the operation according to the manual.

Over View

Introduction

Thank you for choosing Ventnor. It is our commitment to provide our valued customers with the embedded devices equipped with the state-of-the-art technology and the best product services.
Tablet enables the interaction between operators/users and applications, connects industrial control products such as wireless, transducer, battery inside, storage, etc. Tablet adopts a display for displaying and input units such as touch screen, keyboard, audio, kind of sensors etc. for writing working parameters or inputting operation commands. As a digital device for realizing information interaction between human and machine, Tablet is composed of hardware and software. Based on its ample function interfaces and powerful user operational interface, it is very suitable for control units such as medical device, intelligent transportation, industrial field, etc.
Vectron’s Embedded Computer products are based on the most advanced ARM and Rockchip processors and have low-power consumption and high integration. The products are designed for applications such as industrials, medicals, and transportations etc.

Features

Processor| RK3288W, CPU: Quad-core Cortex-A17, up to 1.6GHz GPU: Mali-T764, up to 500MHz
---|---
RAM| 2GB DDR3-1866 ( Optional 4GB )
Flash| 32GB eMMC 5.1 ( Optional 8GB or 16GB )
Storage| 1xMicro SD ( Internal ) ( Optional )
EEPROM| 1Kb
Video Decoder| Real-time video decoder MPEG-2, MPEG-4, H.264, VP8 H.264: 2160p @24fps ( 3840×2160 ) MPEG-4: 1080p@60fps ( 1920×1080 ) MPEG-2: 1080p@60fps (1920×1080 )
Video Encoder| Support video encoder for H.264 Image size is to FHD ( 1920×1080 ) Maximum frame rate is up to1920x1080@30fps
LCD| 27″ TFT LCD
Resolution| 1920×1080
Contrast Ratio| 3000:1
LCM Luminance| 300 cd/m2 ( Typ. )
Support Color| 16.7M colors
LED Life Time| 30000 hours ( Typ. )
Touch Screen| Cap-touch, support for 10 touch.
accelerometer| 3-axis accelerometer
TF card| 1 x TF card Slot ( Memory capacity to be determined ) ( Internal
Debug| 1 x 3.5mm Headphone jack ( Internal )
HDMI| 1 x HDMI 2.0 ( Internal )
USB| 2 x USB HOST ( TYPE A ), standard USB 2.0 ( Internal ) 1 x Micro USB, standard USB 2.0; supports OTG ( Internal )
Button| 1 x Recovery button ( Internal )
WIFI&BT| WIFI: IEEE 802.11 a/b/g/n/ac; BT: 5.0
Speake| 2 x 3W speaker, Drill hole on frame a lower side. ( Internal )
RTC| Supported
OS| Android 6.0.1
Applications| Provide SDK
AC Input| 110V/220V (50/60Hz)
Dimensions| 674 x 413.15 x 60.3mm
Weight| TBD
Temperature| Operation: 0 ~ 50℃, Storage -20 ~ 60℃
Humidity| Operation: 20% ~ 80%, Storage: 10% ~ 90% 12″ AC cable

Order information

UCTTA-42 ( CHA-G80-U682 )| RK3288W ARM Quad-core, Cortex-A17 1.6GHz WIFI 802.11 a/b/g/n/ac, BT 5.0.
---|---

Note: please contact Ventnor for other order information.

Hardware Instructions

Appearance

Appearance

Interface Description

Structure

Hardware Description

This chapter describes the hardware Features, include switch, jumper, connector and PIN function.
The interface description ought to consult the connector sketch map. And attach necessary message such as picture. Indicate the figure, PIN1 and match jack.

Connectors Description

This table is the respective describe valid signal of connector on UCTTA-42 board.
Figure type:

Signal type:

Power button

This button used for power on/off the display plane.

This status is power off.

AC Jack

This port plug in a AC100V~240V cable.
Notice Only one of the two power connectors can be connected. After one of the power connectors is powered on, the other connector is powered on, so Please do not open the lid.

Warning：

• Installation Statement: AC INLET is not accessible during normal use.

Recovery button ( Internal )
This button function is for update. While push the recovery button and power on the display plane, it will work at recovery mode. At this time, user can update the display plane with a micro USB-B cable

Debug interface ( Internal )
he debug interface is reserved for UCTTA-42 display the debug information and
communicate with PC, use the debug cable.

Micro USB ( Internal )
This jack is micro USB-B, used for update.

Ethernet ( Internal )
This jack is 1000M Ethernet, communicate with PC or other equipment’s.

USB 2.0 ( Internal )
This jack is double TYPE-A USB2.0, both them worked at host mode, can connected USB device.

Video ( Internal )
This jack is TYPE-A HDMI, output video and voice.

Tips

Waste Disposal
It is recommended to disassemble the device before abandoning it in conformity with local regulations. Please ensure that the abandoned batteries are disposed according to local regulations on waste disposal. Do not throw batteries into fire (explosive) or put in common waste canister. Products or product packages with the sign of “explosive” should  not be disposed like household waste but delivered to specialized electrical electronic waste recycling/disposal center. Proper disposal of this sort of waste helps avoiding harm and adverse effect upon surroundings and people’s health. Please contact local organizations or recycling/disposal center for more recycling/disposal methods of related products. Comply with the following safety tips:

Do not use in combustible and explosive environment
Keep away from combustible and explosive environment for fear of danger

Keep away from all energized circuits.
Operators should not remove enclosure from the device. Only the group or person with factory certification is permitted to open the enclosure to adjust and replace the structure and components of the device. Do not change components unless the power cord is removed. In some cases, the device may still have residual voltage even if the power cord is removed.
Therefore, it is a must to remove and fully discharge the device before contact so as to avoid injury.

Unauthorized changes to this product or its components are prohibited.
In the aim of avoiding accidents as far as possible, it is not allowed to replace the system or change components unless with permission and certification. Please contact the technical department of Ventnor or local branches for help.

Pay attention to caution signs.
Caution signs in this manual remind of possible danger. Please comply with relevant safety tips below each sign. Meanwhile, you should strictly confirm to all safety tips for operation environment.

Notice
Considering that reasonable efforts have been made to assure accuracy of this manual,
Ventnor assumes no responsibility of possible missing contents and information, errors in contents, citations, examples, and source programs.
Vantron reserves the right to make necessary changes to this manual without prior notice.
No part of this manual may be reprinted or publicly released in forms of photocopy, tape, broadcast, e-document, etc.

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following g two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired o operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be d determined by turning the equipment off and on, the user is encouraged to try to correct the in dereference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help important announcement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

ISED Statement

This device complies with contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS standard(s).
Operation is subject to the following two conditions:

1. (this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may ca use undesired operation.

Radiation Exposure Statement

This equipment complies with Canada radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

S Office: Vantron Technology, Inc. Address: Address: 440 Boulder Court, Suite 300 Pleasanton, CA 94566
Tel:916-202-7042
Email:sales@vantrontech.com

China Office: Chengdu Vantron Technology, Ltd Address: 5/6rd floor, 1st building, No.9, 3rd Wukie East Street, Wuhu District,
Chengdu, P.R. China 610045
Tel: 86-28-8512-3930/3931, 8515-7572/6320
Email:sales@vantrontech.com.cn

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>