Vantron VT-M2M-C335L Gateway User Manual
- June 3, 2024
- Vantron
Table of Contents
VT-M2M-C335L
User Manual
Chengdu Vantron Technology, Ltd.
www.vantrontech.com.cn
Revision History:
| No. | Version | Description | Date |
|---|---|---|---|
| 1 | V1.0 | Initial Version | 2022.06.27 |
Foreword
Copyright Notice
While all information contained herein have been carefully checked to assure
its accuracy in technical details and printing, Vantron assumes no
responsibility resulting from any error or features of this manual, or from
improper uses of this manual or the software. Please contact our technical
department for relevant operation solutions if there is any problem that
cannot be solved according to this manual.
Vantron reserves all rights of this manual, including the right to change the
content, form, product features, and specifications contained herein at any
time without prior notice. The latest version of this manual is at
www.vantrontech.com.cn. Please contact Vantron for further information:
Vantron TechnologyVantron E-mail:
sales@vantrontech.com
The trademarks and registered trademarks in this manual are properties of
their respective owners. No part of this manual may be copied, reproduced,
translated or sold. No changes or other purposes are permitted without the
prior written consent of Vantron. Vantron reserves the right of all publicly-
released copies of this manual.
Notes
Applicable notes are listed in the following table:
| Sign | Notice Type | Description |
|---|---|---|
| Notice | Important information and regulations | |
| Caution | Caution for latent damage to system or harm to personnel |
Statement
It is recommended to read and comply with this manual before operating VT-M2M- C335L which provides important guidance and helps decreasing the danger of injury, electric shock, fire, or any damage to the device.
Disclaimer
Vantron assumes no legal liability of accidents resulting from failure of conforming to the safety instructions.
Limitation of Liability/Non-warranty
For direct or indirect damage to this device or other devices of Vantron
caused by failure of conforming to this manual or the safety instructions on
device label, Vantron assumes neither warranty nor legal liability even if the
device is still under warranty.
The VT-M2M-C335L should be installed, debugged and maintained by professional
people.
The outside antennas are not permitted to be installed or to be changed by
non-professional people. To run the device normally, only specify antennas are
approved to be assembled together by professional people.
Unit shall be used with indoor-use antenna only. No antenna for this unit can
be installed outdoor.
Safety Instructions
- Keep and comply with all operation instructions, warnings, and information.
Pay attention to warnings on this device.
Read the following precautions so as to decrease the danger of injury, electric shock, fire, or any damage to the device.
Precautions
- Pay attention to the product labels/safety instructions printed on silk screens.
- Do not try repairing this product unless declared in this manual.
- Keep away from heat source, such as heater, heat dissipater, or engine casing.
- Do not insert other items into the slot (if any) of this device.
- Keep the ventilation slot ventilated for cooling.
- System fault may arise if other items are inserted into this device.
- Installation: ensure correct installation according to instructions from the manufacturer with recommended installation tools.
- Ensure ventilation and smoothness according to relevant ventilation standard.
Safety Instructions for Power Cables and Accessories
Proper power source only
Start only with power source that satisfies voltage label and the voltage
necessary according to this manual. Please contact technical support personnel
of Vantron for any uncertainty about the requirements of necessary power
source.
Use tested power source
This product still contains a button lithium battery as a real-time clock
after its external power source is removed and therefore should not be short-
circuited during transportation or placed under high temperature.
Place cables properly:
Do not place cables at any place with extrusion danger.
Cleaning Instructions
- Please power off before cleaning the device.
- Do not use spray detergent.
- Clean with a damp cloth.
- Do not try cleaning exposed electronic components unless with a dust collector.
- Support for special fault: Power off and contact technical support personnel of Vantron in case of the following faults:
- The device is damaged.
- The temperature is excessively high.
- Fault is still not solved after the operation according to the manual.
Overview
Introduction
Thank you for choosing Vantron. It is our commitment to provide our valued
customers with the embedded devices equipped with the state-of-the-art
technology and the best product services.
Vantron’s M2M products are based on the most advanced ARM and Intel Atom
processors and have low-power consumption and high integration. The products
are designed for applications of M2M in industrials, financial, retail,
vehicle, and transportations etc.
VT-M2M-C335L Hardware Instructions
Product Appearance
Interface Description
Power Interface
Power connector outlook
| Pin | Description |
|---|---|
| 1 | Power input range DC9-36V |
| 2 | DC Ground |
| 3 | Shell ground |
Ethernet Interface
Standard RJ45 interface, supporting 10M/100M Full/Half Duplex, this is a standard RJ45 Ethernet port
RS232 or RS485 Connector
Standard vertical 1x3x3.81mm male Terminal Block.
| Pin | Description | Remarks |
|---|---|---|
| 1 | TXD1 or RS485_A | IO |
| 2 | RXD1 or RS485_B | IO |
| 3 | GND |
RS485 Connector
Standard vertical 1x3x3.81mm male Terminal Block.
| Pin | Description | Remarks |
|---|---|---|
| 1 | RS485_A | IO |
| 2 | RS485_B | IO |
| 3 | GND |
Boot Configuration
LED
PWR LED: lightindicatesystem power OK(main power up);offindicate system
power turn off
SS LED: User can define by themself.
TX LED: when UART2 send data, TX1 can blink; when UART4 send data, TX2
can blink.
RX LED: when UART2 receive data, RX1 can blink; when UART4 receive data,
RX2 can blink.
DEBUG
CONN, 3.5mm audio con, User can show the debug message and use key board input debug command. It’s RS232 level.
Renew button
Renew button: long press this button will restore the factory setting, the long press time can be setting by user
SD/MMC and Micro SIM socket
The support standard Micro SD card and Micro SIM socket.
Tips
Waste Disposal
It is recommended to disassemble the device before abandoning it in conformity
with local regulations. Please ensure that the abandoned batteries are
disposed according to local regulations on waste disposal. Do not throw
batteries into fire (explosive) or put in common waste canister. Products or
product packages with the sign of “explosive” should not be disposed like
household waste but delivered to specialized electrical electronic waste
recycling/disposal center. Proper disposal of this sort of waste helps
avoiding harm and adverse effect upon surroundings and people’s health. Please
contact local organizations or recycling/disposal center for more
recycling/disposal methods of related products. Comply with the following
safety tips:
Do not use in combustible and explosive environment
Keep away from combustible and explosive environment for fear of danger.
Keep away from all energized circuits.
Operators should not remove enclosure from the device. Only the group or person with factory certification is permitted to open the enclosure to adjust and replace the structure and components of the device. Do not change components unless the power cord is removed. In some cases, the device may still have residual voltage even if the power cord is removed. Therefore, it is a must to remove and fully discharge the device before contact so as to avoid injury.
Unauthorized changes to this product or its components are prohibited. In the aim of avoiding accidents as far as possible, it is not allowed to replace the system or change components unless with permission and certification. Please contact the technical department of Vantron or local branches for help.
Pay attention to caution signs. Caution signs in this manual remind of possible danger. Please comply with relevant safety tips below each sign. Meanwhile, you should strictly conform to all safety tips for operation environment.
Notice Considering that reasonable efforts have been made to assure accuracy of this manual, Vantron assumes no responsibility of possible missing contents and information, errors in contents, citations, examples, and source programs. Vantron reserves the right to make necessary changes to this manual without prior notice. No part of this manual may be reprinted or publicly released in for
FCC compliance statement
This device complies with part 15 of the FCC Rule. Operation is to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 25cm between the radiator & your body
15.21 Information to user. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
ISED Canada compliance statement
This device complies with ISED Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Operation in the band 51505250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems.
This equipment complies with ISED Canada radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 25cm between the radiator & your body
This radio transmitter [IC: 11152A-VTC335L] has been approved by Innovation,
Science and Economic Development Canada to operate with the antenna types
listed below, with the maximum permissible gain indicated. Antenna types not
included in this list that have a gain greater than the maximum gain indicated
for any type listed are strictly prohibited for use with this device.
| Antenna type| Input impedance(Ohm)| Frequency range| Antenna gain
---|---|---|---|---
Wi-Fi 2.4GHz/BT| Monopole| 50| 2.4-2.56Hz| 1.76dBi
Wi-Fi 5GHz| Monopole| 50| 5.15-5.25GHz 5.7- 5.85GHz| 3.12dBi@5.15-5.25 GHz
4.03dBi@5.7-5.85 GHz
US Office: Vantron Technology, Inc.
Address: 440 Boulder Court, Suite 300,
Pleasanton, CA 94566
Tel: +1 916-202-7042
Email: sales@vantrontech.com
China Office: Chengdu Vantron Technology, Ltd
Address: 6th Floor, 1st Building, No.9, 3rd WuKe East Street, WuHou District,
Chengdu, P.R. China 610045
Tel: 86-28-8512-3930/3931, 8515-7572/6320
Email: sales@vantrontech.com.cn
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>