Vantron VT-PNL156-MT65-HD Battery User Manual
- June 4, 2024
- Vantron
Table of Contents
VT-PNL156-MT65-HD
Hardware User Manual
Product Version: 1.1
VT-PNL156-MT65-HD Battery
Change History
This table describes the version and release date.
| Rev. | Date | Description | Author |
|---|---|---|---|
| 1.0 | 2021-06-15 | First release. | Cong Yang |
| 1.1 | 2021-12-02 | Update relevant information | Cong Yang |
Foreword
Copyright
While all information contained herein has been carefully checked to assure
its accuracy in technical details and printing, Vantron assumes no
responsibility resulting from any error or features of this manual, or from
improper uses of this manual or the software. Please contact our technical
department for relevant operation solutions if there is any problem that
cannot be solved according to this manual.
Vantron reserves all rights of this manual, including the right to change the
content, form, product features, and specifications contained herein at any
time without prior written notice.
The trademarks and registered trademarks in this manual are properties of
their respective owners. No part of this manual may be copied, reproduced,
translated, or sold. No changes or other purposes are permitted without the
prior written consent of Vantron.
Vantron reserves the right to all publicly-released copies of this manual.
Symbol Conventions
The symbols that may be found in this document are defined as follows.
| Symbol | Type | Description |
|---|---|---|
| Notice | Important information and regulations | |
| Caution | Caution for latent damage to the system or harm to personnel |
Statement & Disclaimer
It is recommended to read and comply with this manual which provides important
guidance and helps decrease the danger of injury, electric shock, fire, or any
damage to the device.
Vantron assumes no legal liability for accidents resulting from the failure of
conforming to the safety instructions.
Limitation of Liability/Non-warranty
For direct or indirect damage to this device or other devices of Vantron
caused by failure of conforming to this manual or the safety instructions on
the device label, Vantron assumes neither warranty nor legal liability even if
the device is still under warranty. The device should be installed, debugged,
and maintained by professionals. The outside antennas are not permitted to be
installed or to be changed by non-professionals. To run the device normally,
only specified antennas are approved to be assembled together by
professionals.
Unit shall be used with indoor-use antenna only. No antenna for this unit can
be installed outdoors.
Safety Instructions
- Keep and comply with all operation instructions, warnings, and information.
- Pay attention to warnings on this device.
- Read the following precautions so as to decrease the danger of injury, electric shock, fire, or any damage to the device.
- Operations and service instructions are provided with the equipment.
- Unit shall be used with indoor-use antenna only. No antenna for this unit can be installed outdoors.
- The maximum operating temperature is 60°C.
Precautions
- Pay attention to the product labels/safety instructions printed on silk screens.
- Do not try repairing this product unless declared in this manual.
- Keep away from the heat sources, such as heaters, heat dissipaters, or engine casings.
- Do not insert other items into the slot (if any) of this device.
- Ensure ventilation of the ventilation slot.
- System fault may arise if other items are inserted into this device.
- Installation: ensure correct installation according to instructions from the manufacturer with recommended installation tools.
- Ensure ventilation and smoothness according to relevant ventilation standards.
Safety Instructions for Power Cables and Accessories
Use Proper power source only. Start only with a power source that satisfies
the voltage label and the voltage necessary according to this manual. Please
contact the technical support personnel of Vantron for any uncertainty about
the requirements of the necessary power source.
Use a tested power source. This product still contains a button lithium
battery as a real-time clock after its external power source is removed and
therefore should not be
short-circuited during transportation or placed under high temperatures.
Place cables properly: Do not place cables at any place with extrusion
danger.
Cleaning Instructions
- Please power off before cleaning the device.
- Do not use spray detergent.
- Clean with a damp cloth.
- Do not try cleaning exposed electronic components unless with a dust collector.
- Support for special faults: Power off and contact technical support personnel of Vantron in case of the following faults:
- The device is damaged.
- The temperature is excessively high.
- The fault is still not solved after operations according to the manual.
Introduction
1.1 Product Description
Vantron offers both ARM and ATOM based Single Boards Computer (SBC) platforms
including Cirrus Logic EP9315, RockChip RK3128, RK3368, RK3288, RK3399,
Freescale iMX6, iMX8, TI OMAP35xx CortexA8 series, and Intel SkyLake and
ApolloLake processor boards. In addition to offering the standard SBCs, we
also provide professional customization board design services. Our seamless
project management, efficient error-free development process, strong
fundamentals in technology, sufficient human resources, and on-time delivery
will guarantee success in your project development.
Based on the idea of “Application Ready” products and services, our embedded
computers have an embedded basic operating system that includes the drivers of
their interfaces. So it is easy to be used by adding your application software
only. It can speed Time to Market your products and save more costs.
1.2 Connector Description
These tables respectively describe the valid signal of connectors on the
Vantron board.
Table 1-1 Term description (1)
| N/C | Not connect |
|---|---|
| GND | Ground |
| / | Active low signal |
| + | Positive of the difference signal |
| – | negative of the difference signal |
Table 1-2 Term description (2)
| I | Input |
|---|---|
| O | Output |
| I/O | input/output |
| P | Power or ground |
| A | Analog |
| OD | Open drain |
| CMOS | 3.3 V CMOS |
| LVCMOS | Low Voltage CMOS |
| LVTTL | Low Voltage TTL |
| 3.3V | 3.3 V signal level |
| 5V | 5 V signal level |
| USB | 5 V tolerant signal |
| PCIe | PCI Express signal, not 3.3 V tolerant |
| NC | No Connection |
Overview
2.1 Introduction
VT-PNL156-MT65-HD is a tablet packed with an MT8365 processor, USB2.0, built-
in 2GB LPDDR4 dual channel memory, 32GB eMMC 5.1 flash memory, and Wi-Fi/BT.
2.2 Specifications
Table 2-1 Specification
Specifications
SOC| Processor| MTK MT8365(I350). CPU: Quad-Core ARM Cortex-A53
2.0GHz(Max), 12nm
GPU: Mali-G52. 3D graphic accelerator capable of processing 57.6 GFLOPS and
1600M pixel/s, 800MHz.
Memory| RAM| 2GB LPDDR4-3733
Flash| 32GB eMMC 5.1
EEPROM| 2Kb
Display| LCD| 15.6″ TFT LCD
Resolution| 1920 x 1080
Contrast Ratio| 700:1
LCM Luminance| 220 cd/m2(Typ.)
View Angle| Full View
Touch Screen| Cap-touch, support 10-point multi-touch.
Interfaces| Ethernet| 1 x 10M/100Mbps Ethernet, RJ45 connector with
LEDx2
USB| 1 x Micro USB, standard USB 2.0; supports OTG
1 x USB TYPE-C, standard USB 2.0; Only support the host mode.
Button| 1 x Volume+; 1 x Volume-
Wireless| WIFI&BT| 802.11b/g/n/ac, 2.4G/5GHz, BT5 (support A2DP (Advance
Audio Distribution Profile), HFP (Hands-Free Protocol) and HDP (Health Device
Profile)), 2 ANTS (BT&Wi-Fi shared ant)
ANT+| 2.4-GHz Radio support RSSI
Audio| Speaker| Support 2x3W/8Ω speaker.
RTC| RTC| Support
---|---|---
Software| OS| Android 10
Power| DC Input| Support 12V/1A DC power supply.
Design| Dimensions| 415.76 x 301.2 x 38.1mm
Tablet Weight| About 2780g
Environment Condition| Temperature| Operating: 0 ~ 60℃ (Recommended:
25℃) storage: -20 ~ +60℃ (Recommended: 25℃)
Humidity| 5-95%RH (Non-Condensation)
2.3 Order Information
Table 2-2 Order information
Part Order Example
VT-PNL156-MT65-HD| MT8365 ARM Quad-Core , Cortex-A53 2.0GHz(Max)
Wi-Fi 802.11 a/b/g/n/ac, BT 5.0.
Note: Please contact Vantron for other order information.
Hardware Instructions
3.1 Appearance
Figure 3-1 View
3.2 Interface Description
Figure 3-2 Interfaces (1)
Figure 3-3 Interfaces (2) 
3.3 Structure
Download the board structure document from Vantron official website:
www.vantrontech.com.cn
Figure 3-4 Structure
Unit: mm
Hardware Function Description
This chapter mainly describes the main hardware functions of this product, including ANT+, WIFI/BT, audio, display, and USB.
4.1 ANT+ Module
ANT+ module shall support ANT+ communication in at least 1 channel, and RSSI
(Received Signal Strength Indicator).
4.2 Wi-Fi/BT
The wireless module inside the tablet complies with IEEE 802.11 a/b/g/n/ac
standards.
The integrated module provides an SDIO interface for Wi-Fi and Bluetooth.
4.3 Audio
VT-PNL156-MT65-HD has two 3W Speakers.
4.4 Display
VT-PNL156-MT65-HD has a 15.6″ screen. The screen is made up of a display
screen and a touch screen, which are fitted together by full-fit technology.
More parameters are shown in the table.
Table 4-1 Display parameters
| Item | Specifications | Unit |
|---|---|---|
| Screen Size | 15.6″ | Inch |
| Viewing direction | Full View | – |
| Resolution | 1920 x 1080 | – |
| Display Mode | Normally Black | – |
| Number of Colors | 16,194,277 | colors |
| LCM Luminance | 220 (Typ.) | cd/m2 |
| Contrast Ratio | 700:1 | – |
| Interface | EDP | – |
| Touch Screen | Cap-touch, 10-point |
4.5 Ethernet
VT-PNL156-MT65-HD has a network port that supports 10M/100Mbps Ethernet. The
network port hosts two indicators. The green light is a 100M port indicator:
100M Link and Active (Transmitting or Receiving); while the yellow light is a
10M port indicator: 10M Link and Active (Transmitting or Receiving). (The
yellow light needs to be used in a specific LED mode and is not used by
default.
4.6 USB
VT-PNL156-MT65-HD has two USB ports (Type-C and Micro USB ports), both of
which support standard USB2.0. Type-C only supports host mode; While Micro USB
supports master-slave mode. Type-C supports a maximum of 5V/0.5A output; while
Micro USB supports a maximum of 5V/1A output.
Hardware Operation Note
This chapter provides a guide to set up and use some of the features of the
tablet. For more details, see the hardware description.
5.1 Power Preparation
5.1.1 Environment Preparation
Before the device is powered on, please confirm whether the environmental
conditions meet the requirements. Environmental conditions are as follows:
- Operation Temperature: 0°C ~ +60°C
- Operation Humidity: 5-95%RH (Non-Condensation)
5.1.2 DC Power Input
Please confirm the power input is 12V, and the reference current is 1A.
Do not use unauthorized or incompatible power adaptors to charge the device.
Otherwise, fire, explosion, or other incidents may be caused.
5.2 Antenna
The design of the internal antenna of VT-PNL156-MT65-HD is shown in Figure
5-1.
Figure 5-1 Internal antenna
In order to ensure that the tablet functions can work properly, please do not cover the antenna area with metal shielding devices.
Software Instructions
VT-PNL156-MT65-HD has been pre-loaded firmware. For more information, please refer to the software user manual for software operation.
Tips
Waste Disposal
It is recommended to disassemble the device before abandoning it in conformity
with local regulations. Please ensure that the abandoned batteries are
disposed of according to local regulations on waste disposal. Do not throw
batteries into the fire (explosive) or put them in the common waste canister.
Products or product packages with the sign “explosive” should not be disposed
of like household waste but delivered to specialized electrical & electronic
waste recycling/disposal centers. Proper disposal of this sort of waste helps
avoid harm and adverse effect on surroundings and people’s health. Please
contact local organizations or recycling/disposal centers for more
recycling/disposal methods for related products.
Comply with the following safety tips:
Do not use in combustible and explosive environments
Keep away from combustible and explosive environments for fear of danger.
Keep away from all energized circuits.
Operators should not remove the enclosure from the device. Only the group or
person with factory certification is permitted to open the enclosure to adjust
and replace the structure and components of the device. Do not change
components unless the power cord is removed. In some cases, the device may
still have residual voltage even if the power cord is removed. Therefore, it
is a must to remove and fully discharge the device before contact so as to
avoid injury.
Unauthorized changes to this product or its components are prohibited.
With the aim of avoiding accidents as far as possible, it is not allowed to
replace the system or change components unless with permission and
certification. Please contact the technical department of Vantron or local
branches for help.
Pay attention to caution signs.
Caution signs in this manual remind us of possible danger. Please comply with
the relevant safety tips below each sign. Meanwhile, you should strictly
conform to all safety tips for the operating environment.
Notice
Considering that reasonable efforts have been made to assure the accuracy of
this manual, Vantron assumes no responsibility for possible missing contents
and information, errors in contents, citations, examples, and source programs.
Vantron reserves the right to make necessary changes to this manual without
prior notice. No part of this manual may be reprinted or publicly released in
form of photocopy, tape, broadcast, e-document, etc.
Appendix A: How to Contact Us
If you have any problem or want to know more about our products, visit
www.vantrontech.com or contact us.
US Office: Vantron Technology, Inc.
Address: 440 Boulder Court, Suite 300,
Pleasanton, CA 94566, USA
Tel: 925-621-8758
Email: sales@vantrontech.com
China Office: Chengdu Vantron Technology, Ltd
Address: 6th Floor, 1st Building, No.9, 3rd Wu Ke East Street,
Wu Hou District, Chengdu 610045, China
Tel: 86-28-8512-3930/3931, 8515-7572/6320
Email: sales@vantrontech.com.cn
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help with important ann announcement
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body.
ISED Statement
This device complies with contains license-exempt transmitter(s)/receiver(s)
that comply with Innovation, Science and Economic Development Canada’s
license-exempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Radiation Exposure Statement
This equipment complies with Canada’s radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 20cm between the radiator & your body.
The device for operation in the band 5150–5250 MHz is only for indoor use to
reduce the potential for harmful interference to co-channel mobile satellite
systems;
For any questions, please contact Chengdu Vantron Technology, Ltd.
Copyright © Vantron Technology, Ltd. All rights reserved.
Product Version: 1.1
Date: 2021-12-02
Documents / Resources
|
Vantron VT-PNL156-MT65-HD
Battery
[pdf] User Manual
CVC15A, 2A3HV-CVC15A, 2A3HVCVC15A, VT-PNL156-MT65-HD Battery, VT-
PNL156-MT65-HD, Battery
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>