AKG HARMAN CU800 Charging Unit for DHT800 and DPT800 Transmitters User Guide
- June 3, 2024
- AKG HARMAN
Table of Contents
CU800 Charging Unit for DHT800 and DPT800 Transmitters
User Guide
CU800 Charging Unit for DHT800 and DPT800 Transmitters
The charging unit CU800 has been designed specifically for use with the DMS800 wireless system. It is also fully compatible with DMS700. The charger provides two charging slots specially shaped to accept the DHT800 (with the included adapters) and DPT800 transmitters. The charging slots operate completely independently so you can charge two transmitters with rechargeable batteries simultaneously. You do not need to remove the batteries from the transmitter for charging.
CHARGING
STATUS LED INDICATIONS
| LED | STATUS | |
|---|---|---|
| — | The charger is ready to operate, no transmitter is inserted in a charging |
slot.
range| | he voltage and temperature of the batteries inside the inserted
transmitter are being checked. LED flashes until temperature is within
specified range (5-40 °C / 41-104 F).
red| | The batteries are being charged.
green| | The batteries are fully charged; the charging cycle is completed.
red<| | Error
OPERATING NOTES
Always switch OFF the transmitter before charging. Never switch the transmitter ON during the charging cycle. This may cause the charger to falsely indicate a completed charging cycle before charging is actually completed. You may safely remove the transmitter at any time before the charging cycle is completed and you may safely charge the batteries inside the transmitter at any time, even before the batteries are completely discharged. However, to ensure a long lifetime of the rechargeable batteries we recommend to completely discharge the batteries every time, i.e., not to charge the batteries before the battery warning appears on the transmitter display and to charge the batteries to capacity every time, i.e., not to remove them from the charger before the charging cycle is completed. Use no batteries other than the rechargeable types recommended in “Technical Data”. Make sure the charger will not be subjected to vibrations during the charging cycle and will rest firmly on a hard surface. Rechargeable batteries will only reach their full capacity after several charging cycles. If a transmitter with fully charged batteries and another one with dead batteries are in the charging slots, the charging cycle may take up to ten hours. If you insert a transmitter with a dry battery into the charger, the charging cycle will be stopped immediately after the battery test and a few minutes of charging the STATUS LED will start flashing red.
TECHNICAL DATA
| Model | CU800 |
|---|---|
| Operating voltage | Charging unit |
| Recommended batteries | NiMH or NiCd rechargable, minimum capacity 1900 mAh |
| AC voltage | 100 – 240 V AC |
| Charging current | typ. 1.4 A in single-slot mode |
| Charging time | typ. 1.5 hours in single-slot mode (depending on battery type |
and capacity)
Dimensions| 194 x 85 x 82 mm (7,68 x 3,23”)
Net weight| 670 g (23,63 oz.)
Net weight| 670 g (23,63 oz.)
Scope of delivery| 1x CU800 charger, 1x AC adapter EU/US/UK/AU, 4x seize NiMH
rechargable batteries, 2x CU-adapter
Max. ambient temperature| 40°C
DECLARATION OF COMPANY
This product conforms to the standards listed in the Declaration of
Conformity.
To order a free copy of the Declaration of Conformity, visit
www.akg.com or contact
HProTechSupportEMEA@harman.com.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. Shielded
cables and I/O cords must be used for this equipment to comply with the
relevantFCC regulations. Changes or modifications not expressly approved in
writing by AKG Acoustics may void the user’s authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
For other products and distributors worldwide visit
www.akg.com.
Specifications are subject to change without notice.
Printed in China (P.R.C.)
Manufacturer: Harman Professional Inc. 8500 Balboa Blvd, Northridge, CA, 91329
USA
EU Importer: Harman Professional Denmark ApS Olof Palmes Allé 44, 8200 Aarhus
N, Denmark
© 2016 HARMAN International Industries, Incorporated.
All rights reserved. AKG is a trademark of AKG Acoustics
GmbH, registered in the United States and/or other countries.
Features, specifications and appearance are subject to change without notice.
www.akg.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>