zigbee 100W LED Driver Instruction Manual

zigbee 100W LED Driver

100W ZigBee LED Driver(constant voltage)

Important: Read All Instructions Prior to Installation Function introduction

Note:

1. W channel can be turned on through Gateway’s color temperature control interface which will mix RGB channels as 1 channel white and then make color tuning with the 4th channel white. Once turned on, the brightness of white channel will be controlled together with RGB channels.
2. W channel can be controlled separately from RGB channels through RGBW zigbee remote or touch panel’s W button, please refer to their manuals.
   Product Data

condition is removed
Over Temperature| Yes, recovers automatically after fault condition is removed
Environment| Working Temp.| -20℃ ~ +50℃
---|---|---
Max. Case Temp.| 85℃ (Ta=”45℃”)
Working Humidity| 10% ~ 95% RH non-condensing
Storage Temp. & Humidity| -40℃ ~ +80℃, 10% ~ 95% RH
Safety & EMC| Safety Standards| UL8750, CAN/CSA C22.2 No. 250.13-14,

EN61347-1, EN61347-2-13 approved

Withstand Voltage| I/P-O/P: 3.75KVAC
Isolation Resistance| I/P-O/P: 100M Ohms / 500VDC / 25℃ / 70% RH
EMC Emission| EN55015,  EN61000-3-2,  EN61000-3-3
EMC Immunity| EN61547, EN61000-4-2,3,4,5,6,8,11, surge immunity Line-Line 1KV
Others| MTBF| 188300H, MIL-HDBK-217F @ 230VAC at full load and 25℃ ambient temperature
Dimension| 2446432mm (LWH)

• Dimmable LED driver with plastic case , 4 channels 12VDC constant voltage output
• Class 1 power supply, full isolated design
• Built-in two-stage active PFC function, PF > 90, Efficiency > 90%
• Compliant with Safety Extra Low Voltage standard
• Over load, over temperature protection
• ZigBee RGBW LED light device based on ZigBee 0 protocol, supports Touchlink commissioning
• Enables to control ON/OFF, light intensity and RGB color
• W channel can be controlled through Gateway’s color temperature control interface
• W channel can be controlled separately from RGB channels through RGBW zigbee remote or touch panel’s W button
• Can directly pair to a compatible ZigBee remote via Touchlink
• Supports zigbee green power and can bind 20 zigbee green power remotes
• Compatible with universal ZigBee coordinator or gateway products
• IP20 rating, suitable for indoor LED lighting applications
• 5 years warranty

Safety & Warnings

• DO NOT install with power applied to the device.
• DO NOT expose the device to moisture.

Wiring Diagram

Operation

1. Do wiring according to connection diagram correctly.
2. This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee system.

Zigbee Network Pairing through Coordinator or Hub

(Added to a Zigbee Network)

Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will fail. Please refer to the part “Factory Reset Manually”.
Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as instructed by the controller.
Step 3: power on the device, it will be set into network pairing mode (connected light flashes twice slowly), the network pairing mode will last until the device is added to a zigbee network.

TouchLink to a Zigbee Remote

Step 1: Method 1: Short press “Prog” button (or re-power on the device) 4 times to start Touchlink commissioning immediately, 180S timeout, repeat the operation.
Method 2: If the device is already added to a network, it will be set into Touchlink commissioning immediately, 180S timeout. Once timeout, re-power on the device to set it into touchlink commissioning again.

Note:

1. Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.
2. Touch Link after both added to a ZigBee network, each device can link with max. 30 remotes.
3. For Hue Bridge & Amazon Echo Plus, add remote and device to network first then Touch Link.
4. After TouchLink, the device can be controlled by the linked remotes.

Removed from a Zigbee Network through Coordinator or Hub Interface

Factory Reset Manually

Step 1: Short press “Prog.” key for 5 times continuously or re-power on the device for 5 times continuously if the “Prog.” key is not accessible .

Note: All configuration parameters will be reset after the device is reset or removed from the network.

Factory Reset through a Zigbee Remote

(Touch Reset)

Note: Make sure the device already added to a network, the remote added to the same one or not added to any network.

Find and Bind Mode

zigbee-100W-LED-Driver-08

Delete Learning to a Zigbee Green Power Remote

Setup a Zigbee Network & Add Other Devices to the Network

(No Coordinator Required)

Step 1: Short press “Prog.” button 4 times (Or re-power on the device 4 times) to enable the device to setup a zigbee network (connected light flashes twice) to discover and add other devices, 180 seconds timeout, repeat the operation.

Note:

1. Each added device can link and be controlled by max. 30 added remotes.
2. Each added remote can link and control max. 30 added devices.

ZigBee Clusters the device supports are as follows

Input Clusters

• 0x0000: Basic
• 0x0003: Identify
• 0x0004: Groups
• 0x0005: Scenes
• 0x0006: On/off
• 0x0008: Level Control
• 0x0300: Color Control
• 0x0b05: Diagnostics

Output Clusters

• 0x0019: OTA

OTA

The device supports firmware updating through OTA, and will acquire new firmware from zigbee controller or hub every 10 minutes automatically.

Product Dimension

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>