Zigbee Tubular Motor with Transformer AC Supply User Manual
- October 30, 2023
- zigbee
Table of Contents
Zlgbee Tubular Motor
with Transformer(AC Supply)
User Manual
Product Info
Models & Parameters (for details about other parameters, see the product nameplate)
**** Caution!
-
This product i for indoor use only, do not use outdoor or n humid environments.
-
The power supply is AC Supply (AC100~240).
-
The motor will jog in operation, please do not proceed to the next step until it complete.
-
During operation, the effective interval of the ransitter button operation is 10 seconds.
If there s no effective transmitter operation for more than 10 seconds, it will automatically exit the current mode. -
The motor can be paired with max 10 controllers
-
UpperELower imitscannot be set at the same postion, mits saved even povier of.
-
The motor runs constantly for at 6 min max without any other operation.
-
Do not lift the motor by orabting the wire or antenna.
Instructions
Motor head button (H) functions
Functions| Operation| Jogging time| LED lamp flicker|
Note
---|---|---|---|---
Control the UP/STOP/ DOWN of the Shade| Short press| /| /| Can only operate
after the limits are set
Adding/Removing Controller| Hold for 2s| Jog1| Flicker1| Operation needs be
done within 10s
Zigbee connecting| Hold for 6s| Jog2| Flicker2| Entering Zigbee
connectionmode
Direction Reverse| Hold for 10s| Jog3| Flicker3| All
setttioinngrsevsearvseedd after
Reset| Hold for 16s| Jog4| Flicker4| All settings deleted
a.Pairing Motor with Controller
Way 1: Before adding a new controller
Way 2: After motor is
powered on for more than lOs
Way 3:Power on, add controller B via pre-existing controller A
Note: Pairing can not be done under group channel or 0 channel.
b.Direction Reverse
If the limits are not set, and direction goes opposite
Iflimits are set and direction goes opposite.
Note: Do reverse the direction when it goes opposite.
c. Upper&Lower Limits Setting
Note: Upper&Lower limits cannot be set at the same point.
Before mits set, the motor will run in one-touch mode by pressing Up or Down,
hold Up or Down for 25, motor runs in constant-touch model.
Once limits set, press Up or Down, motor runs n constantiouch mode.
d.One-touch/Constant-touch Mode
Constant—touch —————–>One—touch
Same operation can toggle from one-touch to constant -touch mode.
Note: When motor in one-touch mode, hold Up or Down for more than 2s, it
will run in constant-touch mode.
e.Setting and Cancelling Favorite Position
f.Hot key to the Fay. Position
Note: The Fay.position setting only can be done after upper&lower limits set.
g.Adjusting Upper & Lower Limits
Adjust Upper limit
Adjust Lower limit
Note: The operation shoule be done with
4mins.
h.Adjusting Motor Speed
Note: If motor doesn’t jog, the max/min
speed has already been reached. There are 3 speeds adjustable.
i.Removing Controllers
Note: All the settings are saved even
controllers removed(limits set are saved). Controller A/B are already paired
to motor.
j.Cancelling Limits
Note: It is forbidden to run the motor
if installed into the shade without limits. Limits should be set immediately
to protect the shade.
Zigbee connecting
*Connection requirement
a.Make sure the phone is connected to the Wi-Fi network.
b.The Tuya Zigbee gateway device need to be added to the “Smart Life” APP
first, please refer to its manual for details.
-
Download APP
a.Search for “Smart Life” in the app store or scan the QR code
b.Complete account registration and login to the app
https://smartapp.tuya.com/smartlife -
Add Device
a. Make sure the phone is connected to the Wi-Fi network
b. Make sure the Tuya Zighee gateway device is connected to “Smart Life” App
c. Make the motor is ready to be connected to Zigbee by following steps:
d Find the added Tuya
Zigbee gateway on the “Smart Life” App, click “+ o add a sub- device, and then
click “LED already biink”, the APP wil automatically search for motor
device.
e. After adding successiully, clck ” ” to
modiy the device name.
f.After the motor device
is added successfully, the LED on motor head will be on for 10s and then go
of. g. Now the motor can be controlled by App from anywhere, anytime
Troubleshooting
| Fault | Cause | Solution |
|---|---|---|
| Motor does not work | 1.Controller not paired | |
| 2.Motor inactive | 1.Add controller |
2.Hold H button for 2s to activate motor
Motor stops suddenly| 1.Upper & Lower limit set incorrectly
2.Shade exceed rated load| 1.Re-set Upper & Lower limits
2.Adjust load
Motor just goes in one direction| Wrong limits setted| Cancel original limits,
set new limits
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>