Whale SDS081T Switch Connect Transformer User Guide
- June 3, 2024
- Whale
Table of Contents
Whale SDS081T Switch Connect Transformer
Whale Switch Connect Transformer Hardwired Connections
(Direct Connect)
The Whale Switch Connect transformer may be directly wired to compatible
electric showers without the use of a flow switch. The compatible showers and
their connections are shown below:
Mira® Advance Flex Extra 1.1785.005 (J09N)
Triton Omnicare, Safeguard +, Omnicare Design, Safeguard Pumped Care
Redring Selectronic WP
(‘RSEL85WPC or RSEL95WPC’)
Whale Switch Connect Transformer Flow Switch Connections
Electric Shower Settings
In a situation where a hardwired connection with the shower cannot be
established i.e. the electric shower is not compatible with the Whale Switch
Connection transformer, the AK1568 flow switch may be installed in the cold-
water supply to the shower. Always ensure the flow switch is accessible
.
Mixer Shower Settings
When installing a mixer shower two flow switches must be used (an additional
flow switch is required – AK1570 Mixer Valve Conversion Kit). One switch on
the hot-water supply and one switch on the cold-water supply. The plumbing
from the gulley to the pump must be in 22mm pipework to allow for higher flow
rates.
Note: When upgrading an existing installation to a mixer shower and 15mm
pipework cannot be altered, restrict the flow rate from the shower to 8lpm
.
Transformer Settings
The transformer is factory set for a typical Electric Shower installation. See
Fig 2.4
Settings should only be adjusted to suit a specific installation where
required.
To make adjustments, move the jumpers on the base of the transformer to
connect pairs of con-tacts to suit the particular installation as follows:
-
Setting 1: Mixer / Electric (M / E)
Select your type of installation.
M Mixer Valve shower setting.
E (Default Setting) Electric shower setting. -
Setting 2: Flow Setting
≡ (Default Setting) With Setting 1 set to E the pump runs at the optimum speed to remove water delivered by a healthcare electrical shower whilst keeping gulley noise to a minimum.
With Setting 1 on M the pump will remove water from a mixer/blender shower fitted with the 10 ltrs/min restrictor contained in Mixer Valve Conversion kit AK1570, whilst keeping gulley noise to a minimum.
– 0.5, +0.5, +1.0, +2.0, +3.0 Ltrs/min (approx.) These settings are used in conjunction with
Setting 1, E or M, to enable pump speed to be fixed faster or slower to deal with the maximum flow from any shower up to 12 ltrs/min whilst keeping gulley noise to a minimum.
-
Setting 3: Off Delay (10, 30 Seconds)
10 Seconds (Default Setting) is the recom-mended setting for Electric Shower and Mixer Shower installations.
30 Seconds This setting is suitable for installa-tions where water is slow to drain into the gulley. -
Purge Cycle – After 15 minutes the transformer will reactivate the pump for approx 30 seconds to remove any run-off or condensation that has collected in the gulley.
-
Test Button – The Test Button provides a quick and convenient way to test the transformer and pump operation. Press, hold and release the Test Button. The GREEN LED should illuminate on the Test Button and the pump should run.
DO NOT MAKE THE PUMP RUN FASTER THAN NECESSARY
DEFAULT SETTINGS SHOULD NORMALLY BE USED
ActiveLink Diagnostics
The 755.210 transformer includes ActiveLink diagnostics to aid installation and maintenance.
- If the connection to mains power is made and the Test Button is pressed, the green LED will illuminate. If this does not happen check power source, fuses and that all connections compress or contact the electric wire and not the wire insulation.
- With the pump connected, pressing the Test Button will activate it and the green LED. The light will go out as the pump stops after off delay time set on the transformer. Used to clear tray or test pump.
- When the shower is turned on, as water flows throughthe external flow switch(es) or the internal shower switch is closed, the green LED will illuminate to indicate correct operation of switch.
©Copyright Whale 2021 – All rights reserved. Reproduction in whole or in part
without permission is prohibited. WHALE® and WHALE SWITCH CONNECT® are
registered trademarks of Munster Simms Engineering Limited, Bangor, Northern
Ireland trading as Whale. Whale’s policy is one of continuous improvement and
we reserve the right to change specifications without prior notice.
Illustrations are for guidance purposes only. Neither the accuracy nor
completeness of the information contained in this or any product literature is
guaanteed by the Company and may be subject to change at its sole discretion.
MIRA® is a registered trade mark of Kohler Mira Limited.
TRITON® is a registered trade mark of Triton Showers a division of Norcros
Group (Holdings).
REDRING® is a registered trade mark of Glen Dimplex Ventilation & Heating.
SIKA® is a registered trade mark of Dr. Siebert & Kuhn GMbH & Co. KG
GEMS® is a registered trademark of Gems Sensors & Controls.
0345 9090 912
drainagesupport@whalepumps.com
www.whalepumps.com/psd
@Whalecare
Documents / Resources
|
Whale SDS081T Switch Connect
Transformer
[pdf] User Guide
SDS081T Switch Connect Transformer, SDS081T, Switch Connect Transformer,
Connect Transformer, Transformer
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>