tp-link AP7650 Wall Plate Access Point Installation Guide

: June 15, 2024
: tp-link

Table of Contents

tp-link AP7650 Wall Plate Access Point
Network Topology
Pre-Installation Checklist
Installation Steps
Software Configuration
Safety Information
Warranty
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

tp-link AP7650 Wall Plate Access Point

Network Topology

A typical network topology for the AP is shown below:

The AP can only be powered via a PSE device (such as a PoE switch) which complies with Power Source Class 2 (PS2) or Limited Power Source (LPS) of IEC 62368-1. A DHCP server (typically a router) is required to assign IP addresses to the APs and clients in your local network. The management host can be in the same or different network segment with the APs.

Pre-Installation Checklist

Before installation, be sure that you have the following items:

A pre-installed wall junction box
An RJ45 plug
A triangular screwdriver (Only for some models)
A Phillips screwdriver
A PoE switch

Installation Steps

The AP can be mounted into a wall junction box. The junction box should be pre-installed with a running-in-wall Ethernet cable connected to a PoE switch.

Detach the faceplate of the junction box with a Phillips screwdriver (demonstrated with a standard US wall junction box).
Detach the faceplate of the AP with a screwdriver.
Connect the Ethernet cable inside the junction box to an RJ45 plug. Then connect the cable to the UPLINK+PoE port. Position the Ethernet cable to ensure it is not strained.
Note: If the junction box does not have enough room to accommodate the AP without straining the Ethernet cable, replace the junction box with an open‑end or deeper one.
Insert the enclosed screws and tighten them with a screwdriver to secure the mounting bracket.
Note:
- Do not over tighten the screws. If the enclosed screws do not fit the junction box, use the screws attached to the junction box instead.
- For some models, switch the order of Step 3 and Step 4.
Press the faceplate of the AP back into position.

Software Configuration

To quickly set up a wireless network connection with mass APs, please follow the steps below.

Get the Controller from https://www.tp-link.com or contact the sales staff.
Launch the Controller and follow the configuration wizard to create a primary wireless network.
Adopt the AP devices in the Controller management interface to change their status from Pending to Connected.

Safety Information

Keep the device away from water, fire, humidity or hot environments.
• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Do not use the device where wireless devices are not allowed
Adapter shall be installed near the equipment and shall be easily accessible.

Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of device. Please use this product with care and operate at your own risk.

TP‑Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863. The original EU declaration of conformity may be found at https://www.tp-link.com/support/ce

Warranty

For TP‑Link Branded Products Only. For the information about warranty period, policy and procedures, please visit https://www.tp-link.com/en/support
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE (OR BY COUNTRY OR PROVINCE). TO THE EXTENT ALLOWED BY LOCAL LAW, THIS WARRANTY AND THE REMEDIES SET FORTH ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, REMEDIES AND CONDITIONS. TP‑Link warrants the TP‑Link branded hardware product contained in the original packaging against defects in materials and workmanship when used normally in according with TP‑Link’ s guidelines for some period which depends on the local service from the date of original retail purchase by the end‑user purchaser.

For technical support, the user guide and other information, please visit https://www.tp-link.com/support, or simply scan the QR code.