SEALEY AAS10000 Auto Rise Ratchet Axle Stands Instruction Manual
- June 3, 2024
- SEALEY
Table of Contents
SEALEY AAS10000 Auto Rise Ratchet Axle Stands
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instructions
SAFETY
‰ WARNING!
DO NOT OVERLOAD AXLE STANDS BEYOND RATED CAPACITY. OVERLOADING CAN CAUSE
DAMAGE TO, OR FAILURE OF, THE AXLE STANDS. POSITION LOAD ON CENTRE OF
CRUTCH/SADDLE ONLY. ALWAYS USE STANDS IN PAIRS ON HARD LEVEL SURFACE CAPABLE
OF SUSTAINING THE LOAD. USE OF STANDS ON OTHER THAN HARD LEVEL SURFACES CAN
RESULT IN LOAD INSTABILITY AND POSSIBLE LOSS OF LOAD. DO NOT USE ON
TARMACADAM. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN DAMAGE TO AXLE
STANDS, LOSS OF LOAD RESULTING IN PROPERTY DAMAGE, SERIOUS PERSONAL INJURY OR
LOSS OF LIFE.
‰ WARNING! THE STORAGE PIN IS ONLY FOR HOLDING THE CENTRE COLUMN DOWN
WHEN THE STAND IS NOT IN USE. DO NOT APPLY ANY LOAD TO IT.
▲ DANGER! GREAT CARE MUST BE TAKEN TO ENSURE YOU LOWER THE VEHICLE (OR
OTHER LOAD) SLOWLY AND CAREFULLY ONTO THE CENTRES OF THE CRUTCH/SADDLE OF THE
AXLE STANDS.
✓ Use only as specified by the manufacturer.
✓ Ensure the load does not exceed the maximum capacity as marked on the
axle stand, per pair.
✓ Use no more than a single pair of stands either on the front, rear or
one side of the vehicle. Use in pairs.
✓ No alterations or modifications shall be made to this product.
✓ Use on a hard, level surface, e.g. concrete. Do not use on uneven
ground or tarmacadam.
✓ Securely chock wheels in contact with the ground. Before jacking and
placing the stands, apply vehicle handbrake (put automatics in ‘Park’).
✓ Make sure that each stand is securely located under a strong point on
the vehicle; consult the vehicle manufacturer’s handbook for guidance. Ensure
that height adjust locking mechanism is fully located before applying any load
to the axle stand.
✓ Ensure that the load is located centrally on the saddle, and that the
weight is directed through the vertical axis of the stand.
✓ Exercise extra care when using with a three wheeled vehicle or a
trailer. Refer to vehicle manufacturer’s instructions.
✓ Once vehicle is supported, ensure that the vehicle and stands are
stable before starting work. Ensure that it is not possible for the vehicle to
move before commencing any work.
✓ Inspect stands before each use. DO NOT use if they show signs of
damage. DO NOT use if it is suspected that they have been overloaded.
✓ Before commencing any work or going beneath the vehicle, undertake a
risk assessment. Ensure that a responsible person is aware of the work about
to be undertaken.
✓ Replace any labels on the axle stand should they become unreadable.
This applies in particular to any warning or operation instruction labels. If
replacement labels are required, contact your Sealers tackiest.
☓ DO NOT use axle stands on the highway, or anywhere else if it is deemed
to be unsafe.
☓ DO NOT push or twist the vehicle/load whilst it is supported on stands.
☓ DO NOT mix components between stands. Use only as supplied.
☓DO NOT allow children or animals in the vicinity of a vehicle supported
on axle stands.
☓ DO NOT leave a vehicle on axle stands in an area that could be
considered a hazard to others or property.
FOLLOW STEPS 1, 2 AND 3 TO CORRECTLY PLACE VEHICLE/LOAD ONTO AXLE STANDS
INTRODUCTION
Ratchet type axle stands, with cast iron support posts. Auto Rise feature operated by pulling the lever, allowing gas assisted crutch to rise automatically until it meets the axle or chassis of the vehicle. Angled teeth in posts prevent accidental release of load – the more weight applied, the tighter the post is locked. Full width crutch for safe support of load. Manufactured to rigorous safety standards. Sold in pairs.
SPECIFICATION
N.B. In order to obtain the capacities shown, the vehicle must be evenly
supported by the two stands.
Model no: ……………………………………………………… AAS10000
Capacity each:………………………………….. 10 tonne (10,000 kg)
Capacity pair: …………………………………… 20 tonne (20,000 kg)
Minimum height:……………………………………………………510mm
Maximum height:…………………………………………………..775mm
ASSEMBLY
4.1. Insert upper column into base frame, see fig.1.
4.2. Ensure the toothed side of the upper column engages with the locking
lever mechanism.
4.3. Screw in the upper column retaining screw until it just touches the
upper column. Unscrew it half a turn and lock it into position with the lock
nut. Check that the upper column is free to move up and down.
OPERATION
5.1. Refer to manufacturer’s instructions for recommended jacking/support
points. Check to ensure jacking/support points are in good condition.
5.2. Position the stands beneath their support points.
5.3. To adjust the stands: Hold the locking lever up and the gas strut
will raise the upper column to the required height. Push the locking lever
down to lock the pawl into the upper column teeth, see fig.2.
‰ WARNING! ENSURE PAWL IS FULLY ENGAGED WITH TEETH.
5.4. Carefully and slowly lower vehicle onto stands. Ensure load bearing
points sit in the Centre of the saddles and that the stands are stable.
Also ensure that there are no objects or persons that could impede the safe
lowering of the vehicle onto the stands.
▲ DANGER! You must follow THESE instructions carefully and ensure you DO
NOT load the stands off Centre. Failure to adhere to these warnings may cause
damage, injury or loss of life!
MAINTENANCE
6.1. Before each use, check that stands and stand welds are not cracked
and that there are no missing or damaged parts.
6.2. Any suspect axle stands must be removed from service immediately.
6.3. Due to the potential hazards associated with stands, do not misuse,
or make any modification to, the stands or components.
6.4. It is the responsibility of the owner to ensure that the operator
has read these instructions together with the safety features on the side of
the stand and that the operator is aware of the stand uses and limitations.
6.5. Store with the upper column in its lowest position, secured with the
storage pin, see fig.3.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling Centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
