Woosim Systems WSP-W40 4 Inch Mobile Printer User Manual

MODEL: WSP-W40
(4inch Mobile Printer)
Rev. 3.2

Operation Manual

All specifications are subjected to change without notice.

Copyright
WSP-W40 4inch mobile printer operator’s manual.
Copyright ⓒ2021 by Woosim Systems Inc.
All rights reserved.
The information contained in this manual is the property of Woosim Systems Inc.
And may not be reproduced in whole or in part without the prior written permission of
Woosim Systems Inc.

Trademark
a registered trademark of Woosim Systems Inc.
All other trademarks are the properties of their respective companies.

Caution
Some semiconductor devices are easily damaged by static electricity. You should turn the printer
“OFF”, before you connect or removed the cable on the rear side, in order to guard the printer against the static electricity.
If the printer is damaged by static electricity, you should turn the printer “OFF”.

Notice
The contents of this manual are subject to change without notice.

Introduction
The PORTI-W40 is the ideal solution for mobile banking systems, retail, point of sales, Credit card Transaction, other traveling and mobile computing etc.

The general features of the WSP-W40 printer are as follows:
Compact size (138.4 x 88.5 x 45.2mm)

• Lightweight (281g) for true mobility.

• Very silent printing thru direct thermal printing method.

• High speed(50mm/sec, MAX)

• High resolution(203dpi : 8dots/mm)

• USB, Bluetooth Ver3.0 Interface

• Intuitive LED’s indicate Power(on/off), Error, Battery status

•  Support text and graphic printing.

• Easier paper loading by CLAMSHELL design.

• One-touch paper cover

• Printer door open & Paper-out sensor

• Easier maintenance with self-diagnostics.

•  Infield programming – Update Firmware, Download Fonts, and Logos

• Microsoft Windows/Windows CE, Linux, Android, iOS compatible

• Flow control: Software (XON/XOFF)
  ※ Hardware flow control not supported in the printer.

• Agency Approvals

Operating Precautions
Please follow the precautions below to enjoy and maintain the full performance of the printer.

Using the Printer

• Be careful not to drop or bump the printer on a hard surface.

• Do not install the printer in direct sunlight or such areas.
  The suitable environment for the use of the printer is as follows:
  ◆ Operating temperature: -10°C to 50°C
  ◆ Relative humidity: 30% to 80%

• Do not install the printer near devices that generate strong electromagnetic fields such as a copy machine.

• Do not open the platen cover during printing.

• Do not remove or reinstall the communication cable during printing or transmission.

• Do not touch the connectors of the communication during printing.

• Switch the POWER OFF when not in use.

• Do not use another solvent.

• The AC adapter, the battery charger, and the battery pack may become warm when in use. This is normal and is not a malfunction.

• When the battery pack is used at low temperature, the length of time the printer can be used may be shortened.

Thermal Paper Handling

• Store the thermal paper in a cool, dry, and dark place.
• Do not rub the paper with a hard object.
• Do not leave the paper with a hard object.
• Do not allow plastic film, erasers, or adhesive tape to touch the paper for long periods.
• Do not stack the thermal paper with diazo copies immediately after copying or wet-type copies.
• Do not use chemical glue.
• Always use clean thermal paper.

Federal Communications Commission
Radio Frequency Interference Statement
FCC ID: QDD-WSPW40

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment under FCC rules. This Device has been evaluated to comply with the RF exposure requirement for general use limit in portable conditions. It is safe to be used in sold condition.

CE WARNING

• Changes and modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• It is desirable that it be installed and operated with at least 20cm or more between the radiator and person’s body(excluding extremities hand, wrists, feet, and ankles)

Outline

Model classifications

Symbol

**| Standby symbol
IEC 5009, the standby symbol(line partially within a broken circle), Indicates a sleep mode or low power state.
---|---
| Direct current symbol
** This symbol is found on many electronic devices that either require or produce direct current.

Product Part Number System

Example:

1. Port-S40 UART/Bluetooth Part No. ⇒ S40/A1
2. Port-SC30 Bluetooth Only Part No. ⇒ SC30/Z1

Note:
The above table is the interface format that is supported.
But some of the interfaces are not supported according to the product and please contact us if you have any questions regarding the interface.

Specifications.

– KOR: 24X24(16X24)/CHN, JPN: 24X24
Characters per line| – Font A : 69cpl /Font B : 92cpl/Font C : 104cpl
– KOR, CHN, JPN: 34cpl
Optional Characters| Alphanumeric:95, Extended Graphics:128X50 pages, International:10,
Simplified/Traditional Chinese, Japanese, Korean
Resolution| 203dpi, 8dots/mm
Print width| 4-inch (104mm, 832dots)
Printing speed| 50mm /sec (MAX)
Dimensions| 138.4 x 88.5 x 45.2 mm
Weight (w/o paper)| 281g
Interface| USB, Bluetooth Ver3.0
Paper supplied| Thermal roll paper (113mm wide, 38ø)
Barcode supplied| 1- dimension : UPC-A, UPC-E, EAN-8, EAN-13, CODE-39, CODE-93, CODE-128, ITF, CODABAR
2- dimension : PDF417, Micro PDF417, Truncated PDF417, QR-CODE, DATA Matrix, Maxicode
Etc: GS1 DataBar
Driver| Microsoft Windows, Linux
H/W spec.| MCU: RX-32bit, RAM: 128M bit, FLASH: 64M bit
Receive buffer size| 1M bytes
Sensor| Support Paper, Label
Battery| Rechargeable 7.4V DC 1880mAh (Li-ion)
Battery duration| 1-hour continuous printing
Battery Charger| Input (100~240V AC 50~60Hz)
Output(8.4VDC/0.8A), 4hours full charge time
Environment Conditions| Temperature| -10°C ~ 50°C (operating)
-20°C ~ 70°C (storage)
Humidity| 30% – 80% (operating)
10% – 90% (storage)
MCBF (Mean Cycle Between failure)| Mechanical| 37,000,000 lines
Head| Approximately 50Km

Setting up the printer

Printer & Accessories

Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance.

OPTIONAL

External Battery Cradle

Printer Features

2.2.1 Part name

2.2.2 Dimensions

Replacing the paper roll

Note:
Be sure to use paper rolls that meet the specifications.
Do not use paper rolls that have the paper glued to the core because the printer can not detect the paper end correctly.

1. Make sure that the printer is not receiving data; otherwise, data may be lost.
2. Open the paper cover using a finger on both sides of the printer, and remove the remaining paper.
3. Insert the paper roll as shown.
4. Tear the excess paper off using the edge of the paper door as a tear bar.

Power supply

2.5.1. Internal power supply
The following specification is requested for the Power supply.
Rated voltage : DC 8.4V / 0.8A
Avoid using a power supply whose power capacity of power current is extremely high.

2.5.2. Installing the Battery
Warning:

• Before installing or removing the battery pack, ensure the printer is OFF.

• If the printer is not used for a long period of time, remove the battery pack from the printer.

• Risk of explosion if the battery is replaced by an incorrect type.
  Dispose of used batteries according to the instructions.

• Batteries are provided not being charged. Please charge the battery before use.

① To install the battery pack, proceed as follows:
-Insert the Battery Connector in the direction of the arrow.

② Removing the battery pack
– Turn the printer power off and push the battery pack lock and lift up the direction of the arrow.

③ The battery pack installs into External Battery Cradle.
– Insert the battery pack in the direction of the arrow.

2.5.3. Recharging the battery
For recharging the battery pack, install the battery pack in the printer or the External Battery Cradle.
Insert the battery charger into the charge connector of the printer or the External Battery Cradle.

NOTE:

• While charging the printer, turn off the printer power.

• Do not remove the battery during charging.

• The battery is consumable parts and when purchasing, compared to the use hour it gradually decreases. (Warranty 6 months)

• If the printer is not used for a long time, unplug the power cord from the printer and outlet.

• The recharging time depends on the voltage level and ambient temperature of the battery.
  Normally, it takes about 4 hours to recharge a battery pack.

• You must use only the supplied adapter.

• Red Lamp: charging the battery.
  Green Lamp: charging is finished.

Set operation mode

In keeping on pressing the Feed and Power button simultaneously until after the ERROR lamp blinks 5 times, the printer comes out at the circumstance to change the printer mode. (refer to Table 2)

• POWER button: used for changing OPTION status. ( Error Lamp )
• FEED button: used for changing MODE status. ( Power Lamp )

[Example] The defaults of the printer are: USB/Density Low/Mark No Use/Sensor High/PWDN 5 min SLP
If a user wants to modify the defaults with Bluetooth/Density High/Mark Use/Sensor Low/PWDN No Use

• Press FEED & POWER Button during the Error Lamp flickers 5 times.
  → You will see the Power Lamp and the Error Lamp flickers once.
  → Press the POWER Button twice and the Error Lamp flickers 3 times.
  And then, the interface mode has set to Bluetooth mode.

• When you press the FEED Button once again, Power Lamp flickers 2 times, and Error Lamp flickers once.
  → Press POWER Button twice, Error Lamp flickers 3 times.
  And then the density has set to Density high.

• When you press the FEED Button once again, Power Lamp flickers 3 times, and Error Lamp flickers once.
  → Press POWER Button once, Error Lamp flickers twice.
  And then the mark has been set to Mark using.

• When you press the FEED Button once again, Power Lamp flickers 4 times and Error Lamp flickers 4 times.
  → Press POWER Button once, Error Lamp flickers once.
  And then the sensor has set to Sensor Low.

• When you press the FEED Button once again, Power Lamp flickers 5 times and Error Lamp flickers 6 times.
  → Press POWER Button 6 times, Error Lamp flickers once
  And then the power down has set to Power-down no use.

If all the modes have been set, press the POWER Button and the FEED Button at the same time. After then release the buttons at the same time.
Bluetooth/Density High/Mark Use/Sensor Low/PWDN No Use

Memory switch table

| Mode| Option| Etc.| | Mode| Option| Etc.
---|---|---|---|---|---|---|---
1| Communi-cation Port| 1| USB| | 5| Power Down| 1| No use|
2| USB(Pro)| | 2| 1min Sleep|
3| Bluetooth| | 3| 2min Sleep|
4| Bluetooth(Pro)| | 4| 3min Sleep|
5| Bluetooth(iAP)| V| 5| 4min Sleep|
2| Density| 1| Low| | 6| 5min Sleep|
2| Medium| | 7| 1min Off|
3| High| | 8| 2min Off|
3| Mark| 1| No use| | 9| 3min Off|
2| Use| | 10| 4min Off|
4| Sensor sensitivity| 1| Low| | 11| 5min Off|
2| Medium 1| |
3| Medium 2|
4| High|

< Table 2 >

Notice: Bluetooth(iAP) is the mode which is used in iPod, iPhone, and iPad Whole aspect.
Etc. (V): no function due to the specification of the product.

Interface

USB

The WSP-W40 printer has a USB interface and is connected by means of a 5 pin mini USB socket.
In the following table, the signals present on the Mini- USB socket are listed:

NOTE:

• If you connect the printer interface cable is converted to USB mode.
• When data receiving, when it removes the communication cable, it loses data.

Bluetooth

Using the printer

Control panel

Button

Do not operate the mode button without instructions.

LAMP

– Power:
(GREEN)| The printer is ON and ready to receive data.
---|---
– Error:
(RED)| Indicates a fault condition or a printer error. (details: no paper, paper cover opened. etc.)
– Battery Power: (GREEN)| These lamps(Green) indicated the battery power remaining.
The battery gain in quantity and these lamps are on the decrease.
If so, you must recharge the battery by using the battery charger.

The self-test

Self-Test prints out the current setting value of the printer. The way of self-test is as follows.

1. Insert proper paper into the printer.
2. Power on while pressing the feed button to start the self-test.
3. The printer will print out the current status. (F/W version and set contents)
4. And then the pattern of characters will be printed out.
5. Self-test will be finished automatically and turned to the standby status.

※ In case the printer does not work properly, please contact the Woosim customer service center.

Consumable Parts

Recommended paper

Cautions

1. Do not paste the paper to the core. And the roll paper which has
   Near-end mark printing on its near end is recommended.

2. Chemicals or oil may change the color of paper, or printed Characters may fade.

3. Change of paper color starts from approx 70 ℃.
   Pay attention to heat, humidity, and sunlight.

4. The color of paper may be changed by being scratched by a nail or hard metal, etc

Printing position

Revision History

http://www.woosim.com

References

• 우심시스템

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>