TORO 08132 Beacon Kit Instruction Manual

TORO 08132 Beacon Kit Instruction Manual

Loose Parts

Installation

Use the chart below to verify that all parts have been shipped.

the overhead console kit only)and route the wire harness.
4| Beacon switch| 1| Install the beacon switch.
5| Beacon mountBoltNuts| 122| Install the beacon mount.
6| BeaconBeacon socket assembly| 11| Install the beacon.
7| No parts required| —| Install the canopy.

Important: You must install the Overhead Console Kit (Model 08130) before you install this kit.

Preparing the Machine

No Parts Required

Procedure

1. Park the machine on a level surface.
2. Shift the transmission lever to the P (Park) position.
3. Shut off the engine and remove the key.
4. Disconnect the negative (-) battery cable from the battery post.

Removing the Canopy

No Parts Required

Procedure

Remove the bolts, washers, and spacers securing the canopy (Figure 1) and remove the canopy.
Retain the canopy, bolts, washers, and spacers.

g363987
_
Figure 1_

2-person canopy shown

1. Canopy
2. Hex-head bolt (1/4 x 1-1/4 inches)
3. Sealing washer
4. Spacer

Removing the Console and Routing the Wire Harness

If You Previously Installed the Overhead Console Kit Only

No Parts Required

Procedure

1. Remove the 8 screws securing the overhead console and remove the overhead console (Figure 2).
   Retain the 8 screws and overhead console for later installation
   g363607
   
   Figure 2

2. Remove the console-switch bracket from the overhead console (Figure 3).
   Retain the bracket and 4 screws for later installation.
   g364119
   
   Figure 3

3. Route the wire-harness leg with the 2 spade terminals toward the left, rear area of the roll-bar posts (Figure4).
   g364200
   
   Figure 4
   

4. Spade terminals

5. Install the previously removed console using the 8 screws (Figure 2).
   Torque the 8 screws to 339 N∙cm (30 in-lb).

6. Route the female 8-socket connector labeled BEACON SWITCH through the opening where you removed the console switch bracket (Figure5).
   g364198
   
   Figure 5
   

Installing the Beacon Switch

Parts needed for this procedure:

1. Beacon switch

Procedure

1. 1. From the under side of the cab controls panel, press the plug out of the hole shown in Figure 6.
   g364024
   
   Figure 6
   

2. Install the switch into the console-switch bracket (Figure 6).

3. Align the console-switch bracket into the opening and connect the rocker switch to the female 8-socket connector (Figure 7).
   g364199
   
   Figure 7

4. Secure the previously removed console-switch bracket to the overhead console (Figure 3). Torque the 4 screws to 11.3 N∙m (100 in-lb).

5. Connect the beacon switch to the wire-harness connector labeled BEACON SWITCH into the hole in the control panel (Figure 6).

Installing the Beacon Mount

Parts needed for this procedure:

• 1 Beacon mount
• 2 Bolt
• 2 Nuts

Procedure

Use 2 bolts and 2 nuts to secure the bracket to the left-side rear lifting point of the roll bar as shown in Figure 8.

g363962

Figure 8

1. Nut
2. Beacon mount
3. Bolt

Installing the Beacon

Parts needed for this procedure:

• 1 Beacon
• 1 Beacon socket assembly

Procedure

1. Remove the beacon connector from the beacon socket (Figure 9).

2. Route the wire harness up through the jam nut, washer, beacon mount, beacon socket, and connect it to the beacon connector (Figure 9).

3. Install the beacon connector into the beacon socket by rotating the beacon socket (Figure 9).
   Note: This will prevent twisting of the wire harness.

4. Mount the beacon socket to the beacon mount with the jam nut included (Figure 9).

5. Plug the beacon onto the socket and tighten the wing nut.

g364022 _

Figure 9_

1. Beacon
2. Beacon connector
3. Beacon socket
4. Beacon mount
5. Washer
6. Jam nut
7. Wire harness

Installing the Canopy

No Parts Required

Procedure

Secure the previously removed canopy using the bolts, washers, and spacers (Figure 1).

Connecting the Battery

No Parts Required

Procedure
Connect the negative battery cable to the battery post.

Operation

Operating the Beacon Switch
Press the beacon switch to activate and deactivate the beacon.

© 2021—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com

Original Instructions (EN) Printed in the USA All Rights Reserved

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>