BARATZA Virtuoso Coffee Grinder User Guide

June 11, 2024
BARATZA

BARATZA logo

BARATZA Virtuoso Coffee Grinder

BARATZA Virtuoso Coffee Grinder

Parts Identification

  1. Hopper Lid
  2. Bean Hopper
  3. Grind Setting indicator
  4. Hopper Gasket
  5. Removable Ring Burr
  6. Grind Settings
  7. LED Display
  8. Dial
  9. Grounds Bin with Max Fill Line
  10. Brush*
  11. Weighted Base
  12. Grind Adjustment Ring
  13. Grind Adjustment Tab
  14. Burr Lifting Tabs
  15. Center Cone Burr
  • included in grounds bin

BARATZA Virtuoso Coffee Grinder 1

INITIAL SETUP

For the full manual, visit baratza.com/documentation

  1. Remove the contents from the packaging and hand-wash the hopper lid (1), bean hopper (2), and grounds bin (9) in warm, soapy water. Let air dry. Do not wash the ring burr (5) in water or it will rust.
  2. To install the hopper, align the silver grind setting indicator (3) with the triangle near grind setting 40 (6). Press the hopper down and twist clockwise into place. The grinder will not start without the hopper installed.*
  • If there is difficulty in installing the hopper: Ensure that the ring burr (5) is fully seated in place. The grind adjustment ring (12) must be rotated fully counterclockwise using the grind adjustment tabs (13) for the hopper to be installed.

When grinding into the grounds bin, coffee tends to mound up. To prevent clogging, empty the grounds before they reach the max fill line.

CHOOSING A GRIND SETTING

Rotate the hopper to adjust to the desired grind setting. When adjusting the grind setting, the grinder must be running or completely empty of beans to prevent damage to the grinder. Below are suggested starting points for what grind settings to use for common brew methods. Coarser or finer grinding may be needed depending on recipe requirements and taste preference. Additional information can be found at baratza.com/grinding-tips

Finer Grind = lower numbers
Coarser Grind = higher numbers

 | Espresso| AeroPress| Hario V60| Automatic Brewer| Chemex| French Press
---|---|---|---|---|---|---
Suggested Setting| 8| 12| 15| 18| 20| 28

GRINDING OPERATION

The Virtuoso+ will grind for a predetermined length of time, shown on the display (7) in seconds. To adjust the timer and operate the grinder:

  1. Rotate the dial (8) on the display clockwise to increase the grind time in 1.0 second increments, or rotate counterclockwise to decrease the grind time in 0.1 second increments.
  2. The maximum grind time is 40.0 seconds, and the minimum is 0.1 seconds. The timer will loop to 40.0 if adjusted below 0.1, and will loop to 1.0 if adjusted above 40.0.
  3. Press the dial to start grinding. The grinder will automatically stop at 0.0 seconds, or the dial can be pressed again to pause grinding.
  4. To grind continuously without the timer, press and hold the dial for 3 seconds to enter pulse mode. “P” will be shown on the display. The grinder will now grind for as long as the dial is held down, and the timer will count up in seconds as the grinder is in operation. The maximum grind time is 40.0 seconds in this mode. Rotate the dial more than two clicks to exit pulse mode.

If You Need Further Support:

In US & Canada contact
Support@baratza.com
or 425-641-1245
or toll free 877-701-2021

If you think your grinder is not performing correctly, go to our troubleshooting guides at baratza.com/troubleshooting
Outside North America, the warranty is provided by the company you purchased from. For service, find the nearest importer at baratza.com/international- importers-and-retailers

Safety Information

Please read the information below very carefully. It contains important safety information for this appliance.
Please keep these instructions for future reference.

  • Use only with AC current and the correct voltage. See the label on the base of the grinder to determine the correct voltage.

  • Only clean the grinder housing with a dry or slightly damp cloth. Do not immerse the grinder, plug or cord in water or any other liquid.

  • Baratza will not accept any liability for damage, injury, or warranty if the grinder is used other than for its intended purpose (i.e. grinding roasted whole coffee beans) or is improperly operated or repaired.

  • Do not operate the grinder with a damaged cord or plug.
    If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

  • Keep the appliance and its cord out of reach of children aged less than 8 years.

  • Do not leave your grinder unattended while turned ON.

  • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

  • Cleaning and user maintenance shall not be made by children without supervision.

  • Always unplug the grinder from the electrical supply before assembling, disassembling or cleaning. To unplug, grasp plug and remove from the outlet. Never pull on the cord.

  • CAUTION: ALWAYS unplug the electrical supply cord prior to cleaning the grinder

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals