SEALEY AP7200.V2 5 Level Racking Unit 200kg Capacity Per Level Instructions
- June 3, 2024
- SEALEY
Table of Contents
SEALEY AP7200.V2 5 Level Racking Unit 200kg Capacity Per Level
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
**Refer to instructions
**
SAFETY
‰ WARNING! Ensure Health & Safety, local authority, and general workshop
practice regulations are adhered to when using this racking unit.
✓ Locate racking unit in a suitable work area.
✓ Keep the work area clean, uncluttered and ensure there is adequate
lighting.
‰ WARNING! Use racking unit on level and solid ground, preferably
concrete. For added safety fix unit to a wall.
✓ Keep the racking unit clean and tidy in accordance with good workshop
practice.
✓ Keep children and unauthorized persons away from the work area.
✘ DO NOT use the racking unit for any purpose other than that for which it
is designed.
✘ DO NOT use the racking unit outdoors.
✘ DO NOT place the racking unit in a damp or wet location or an area where
there is condensation.
✘ DO NOT clean the racking unit with any solvents which may damage the
surfaces or the protective coating.
✘ DO NOT move the racking unit when there are items placed on it.
✘ DO NOT overload the racking unit.
INTRODUCTION
Fully painted steel frame with five MDF shelves. 200kg capacity per level
giving a maximum capacity of 1000kg per rack. Bolt-less design means no tools
required to assemble. Two piece uprights allow use as a single bay rack or
split into two separate shelf systems or workstations. Ideal for use in
conjunction with Model No. AP7150C corner racking unit.
Dimensions W x D x H: 900 x 400 x 1830mm
CONTENTS
3.1. Unpack the unit and confirm that all the parts listed below are
present. Refer to Parts List below.
3.2. Assemble the unit on a solid, level surface. Avoid carpet. A second
person will be required to help with assembly.
ASSEMBLY
4.1. Assemble the racking unit in the sequence below, referencing the
parts list overleaf.
4.2. Use a rubber mallet to tap the brackets together.
Step 1
Place foot end caps onto the bottom of the 4 legs ‘D’. Note upright
position.
Place shelving bracket ‘A’ onto the legs ‘D’. A rubber mallet can be used to
lightly tap all brackets into the keyholes of the legs into place. Allow one
keyhole free between the foot end cap and the shelving bracket
Step 2
Use shelf bracket ‘B’ for the side brackets using the shelf bracelet from
Step 1 as a guide for height. Allow 1 keyhole free from the ground as shown in
the diagram. Use same shelving bracelets for opposing sides as shown in the
diagram. Place brace ‘C’ as shown.
Parts List:
Step 3
Place MDF board on bottom shelf to minimize buckling. Join the upper legs
to the lower legs with the connector pins. Note upright position. Note: The
legs are designed to sit directly on top of each other – don’t overlap them.
Handy Hint:
Flathead screwdriver rimy be used to tap in connector pins.
Step 4
Fix brackets ‘B’ so that the top rivets sit on the upper legs and the
bottom rivets sit on the lower legs. Repeat with brackets ‘A’- , followed by
brace ‘E’ as shown.
Step 5
Fix brackets ‘B’ at the very top allowing room for the MDF board to sit
flush against the legs. Repeat with brackets ‘A’.
Step 6
Apply remaining brad as above to desired height. Ensure that braces ‘C’ are
fixed to all shelves
Step 7
Place the MDF boards on shelves, ensure they are sitting flush against the
edge of the shelf brackets
Parts support is available for this product. Please email sales@sealey.co.uk or telephone 01284 757500
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice. Please note that other versions of this product are available.
If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk
or 01284 757505. Important: No Liability is accepted for incorrect use of
this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
Documents / Resources
|
SEALEY AP7200.V2 5 Level Racking Unit 200kg Capacity Per
Level
[pdf] Instructions
AP7200.V2, 5 Level Racking Unit 200kg Capacity Per Level, Unit 200kg Capacity
Per Level, Capacity Per Level, 5 Level Racking Unit, Racking Unit
---|---
|
SEALEY AP7200.V2 5 Level Racking Unit 200kg Capacity Per
Level
[pdf] Instruction Manual
AP7200.V2 5 Level Racking Unit 200kg Capacity Per Level, AP7200.V2, 5 Level
Racking Unit 200kg Capacity Per Level, Racking Unit 200kg Capacity Per Level,
200kg Capacity Per Level, Capacity Per Level, Per Level, Level
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>