GARMIN K 5X Dog Locator Device User Manual
- June 3, 2024
- Garmin
Table of Contents
- GARMIN K 5X Dog Locator Device
- Getting Started
- Charging the Dog Collar Device
- Acquiring Satellite Signals
- Adding a Dog to the Alpha® Handheld Using Wireless Pairing
- Fitting the Collar on Your Dog
- Dog Tracking
- Device Information
- Securing the Antenna and Antenna Keeper to the Collar
- Dog Collar Device Specifications
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
GARMIN K 5X Dog Locator Device
Getting Started
WARNING
See the Important Safety and Product Information guide in the product box
for product warnings and other important information.
Dog Collar Device
NOTE: Your dog collar device may look different than the device
pictured.
Turning On the Device
On the dog collar device, hold the power button until the status LED
flashes and the collar beeps.
Turning Off the Dog Collar Device
Hold the power button until the status LED turns solid red and the device
beeps.
Charging the Dog Collar Device
NOTICE
To prevent corrosion, thoroughly dry the contacts on the collar and the
surrounding area before connecting the charging clip.
NOTE: Your dog collar device may look different than the device pictured.
You should fully charge the battery before you use the device for the first
time. Charging a fully depleted battery takes about five hours.
- Snap the charging clip 1 onto the device 2
- Plug the small end of the power cable into the mini-USB port on the charging clip cable.
- Plug the power cable into a power source. The status LED is solid red when the collar is charging.
- After the status LED turns solid green, remove the charging clip from the collar.
Acquiring Satellite Signals
Both the collar and handheld device must acquire satellite signals before you put the collar on your dog. Acquiring satellites can take a few minutes.
- Go outdoors to an open area.
- Turn on both devices. in the status bar shows the GPS signal strength.
When the collar has acquired satellite signals, the status LED flashes a double-blink or triple-blink in green.
Adding a Dog to the Alpha® Handheld Using Wireless Pairing
-
If the dog collar device is on, turn off the dog collar device.
-
Hold the power key on the dog collar device until the device emits two series of beeps (about 2 seconds),and then release the power button.
The status LED flashes rapidly in green. The dog collar device is now ready to be linked, or paired, with a handheld device. -
On the handheld device, select Dog List > Add Dog.
-
Select an option:
- If you are near the dog collar device, select Pair Collar, and follow the on-screen instructions.
- To pair a dog collar device by receiving the information from another handheld device, select Receive from Handheld.
NOTE: To successfully pair the device, the other handheld device must be wirelessly sharing the dog collar device information.
-
After successfully adding the dog collar device, enter the name of the dog, and select .
Fitting the Collar on Your Dog
CAUTION
Do not spray the device or collar with harsh chemicals including but not
limited to flea or tick spray. Always ensure that any flea or tick spray that
is applied to the dog is completely dry before placing the collar on the dog.
Small amounts of harsh chemicals can damage the plastic components and collar
laminate.
Before you can put the collar on the dog, you must pair the handheld device and collar, and acquire satellite signals.
-
Position the collar with the communication antenna pointing up, the GPS antenna facing up, and the LEDs facing forward.
-
Place the collar around the middle of the dog’s neck.
-
Tighten the strap so it is snug around the dog’s neck.
NOTE: The collar should fit tightly and should not be able to rotate or slide on the dog’s neck. The dog must be able to swallow food and water normally. You should observe your dog’s behavior to verify the collar is not too tight. -
If the strap is too long, cut off the excess, leaving at least 7.62 cm (3 in.) to spare.
Dog Tracking
The handheld device allows you to track your dog or multiple dogs, using the tracking compass or map. The map displays your location and your dog’s location and tracks. The compass pointer indicates the direction of the dog’s current location.
Communication with the Collar
You should keep an unobstructed line of sight between your handheld device and
the dog collar device to produce the best communication signal. To achieve the
best line-of-sight conditions, you should move to the highest elevation point
in your area (for example, on the top of a hill).
Device Information
Getting the Owner’s Manual
You can get the latest owner’s manual from the web.
- Go to www.garmin.com/support.
- Select Manuals.
- Follow the on-screen instructions to select your product.
Updating the Dog Collar Device Software
Before you can update the dog collar device software, you must connect the dog
collar device to a computer. NOTE: PC only. Updating the software does not
erase any of your data or settings.
- Go to www.garmin.com/products/webupdater.
- Follow the on-screen instructions.
VHF Radio Information
This product may be used only on specific radio frequencies, which vary
depending on the country of use. The handheld device and the dog device allow
the user to install a different antenna. Changing the antenna can result in
improved radio performance and higher radiated power. You must not use the
device with a third party antenna or an antenna not approved by Garmin®. Go to
www.garmin.com/tracking-legal for details about the performance and radio
frequency of this product, lawful accessories, and power limits for countries.
Securing the Antenna and Antenna Keeper to the Collar
NOTICE
When using cable ties, ensure no sharp edges are in contact with your dog’s
skin.
You can secure the antenna and antenna keeper to the collar to optimize the
fit of the dog collar device on your dog. For maximum radio performance, the
antenna should be pointed straight up when positioned on your dog. Depending
on the size of your dog’s neck, you may need to use cable ties to properly
position the antenna.
- Secure the antenna keeper1 to the collar with one of the provided cable ties 2
- Secure the antenna3 to the collar with one of the provided cable ties 4
- Cut off the excess length from the cable ties.
Dog Collar Device Specifications
© 2022 Garmin Ltd. or its subsidiaries
Garmin®, the Garmin logo, Alpha®, and ANT+® are trademarks of Garmin Ltd. or
its subsidiaries, registered in the USA and other countries. These trademarks
may not be used without the express permission of Garmin.
Other trademarks and trade names are those of their respective owners.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>