BORMANN PRO BBC8520 Electric Power Bank User Manual

Built to last. BBC8520
037316

WARNING: FULLY CHARGE IMMEDIATELY AFTER PURCHASE. Fully recharge after each jump-starting, or every 3 months to ensure long battery life.

Safety instructions

WARNING: Please read and understand all important safety and operating instructions before using this item. In addition, please read and follow all vehicles and
battery manufacturers’ instructions and cautionary markings.

1. Use the Device for jumpstarting a 12V LEAD-ACID battery only. Do not attempt to jump-start a vehicle with a non-rechargeable or defective battery.

2. Working in the vicinity of a lead-acid battery is dangerous. Batteries generate explosive gases during normal operation. Use in a well-ventilated area. Battery acid
   can cause permanent blindness. Avoid touching eyes while working near the battery.

3.  Do not smoke, strike a match, or cause a spark in the vicinity of the battery or engine. Avoid explosive gas, flames and sparks.

4. Remove all personal jewelry, such as rings, bracelets, necklaces, and watches before jumpstarting operations. These items may produce a short-circuit that
   can cause severe burns.

5. To avoid damage to the vehicle’s electrical system, do not use the Device on a vehicle that has no battery installed.

6. Use of an accessory not recommended or sold by the manufacturer may result in a risk of fire, electric shock or injury to persons. Do not operate with dam-
   aged accessory(s).

7. Locate the Device as far away from the battery as jumper cables permit.

8.  Do not expose to rain or wet conditions.

9. To reduce the risk of damage to the electric plug and cord, pull by the plug rather than the cord when disconnecting.

10. Operate with caution if the jump starter has received direct hit of force or been dropped. Have it checked and repaired if damaged?

11. Any repair must be carried out by the manufacturer or an authorized repair agent in order to avoid danger.

Description of main functions/Intended use

It features low voltage protection (for device itse ff, s f, reverse polarity protection and short circuit protection. This item can instantly jump-start most single battery vehicles, up to 45+ (over 45) tiggs o e, The device is also equipped with USB power output and an LED flashlight.

Technical data

2)19V/3.5A for Laptops
3)12V/10A for automotive devices
4)LED Flashlight (On, Strobe, SOS)
5)12V emergency Jump Start up
Starting Current:| 300A
Peak Current:| 500A
Lifetime:| >1000 Cycles

• The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products. The parts described/illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.
• Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.
• To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.

Description of main parts

1. 1.LCD
2. 15V/1A Input Port
3. 12V Output Port
4. 19V Output Port
5. USB Outputs
6. Flashlight Button
7. Power Button
8. ENGINE START socket
9.  LED Flashlight

Operating instructions

Smart Cables “BOOST” Mandatory Operations

1. If with the correct connection between Jump Starter and vehicle battery (Red LED keeps on and green LED is off), press and hold the BOOST button for 3 seconds (after a buzzer sound, the green LED is on and red LED is off). Usually this is because the vehicle battery capacity is rather low.
2. Start the engine (refer to the section “jump starting”).

Cautions:

1. Under normal circumstances, do not use the mandatory operations.
2. The spark proof, reverse polarity protection and short circuit protection features are disabled after the Boost button is pressed. Pay very close attention to the polarity of the battery before using this mode. Do not allow the positive and negative battery clamps to touch or connect to each other as the item will generate sparks and high heat if not used properly.

LED and Buzzer Communication:

Ready to start the engine.
3| Slow flash| Off| No buzzer| The lithium battery voltage in the device is rather low.
4| Slow flash| Off| Fast buzzer| Have not turned on the ignition switch within the regulated time. To resolve this, you need to remove clamps from the vehicle battery and connect again when No.1 condition occurs.
5| Fast flash| Off| Fast buzzer| Red black clamps are connected with each other.
6| Fast flash| Off| Fast buzzer|  Reverse connection of clamps.
7| Off| Fast flash| No buzz;| English is started.
8| Off| Fast flash| No buzzer| Vehicle att of is hi a Jump Starter.

Connecting to the battery a QS wMlghs

1.  Identify the polarity of battery posts. The positive battery terminal is typically marked Neer ors (POS#F,+). The negative battery terminal is typ- ically marked by these letters or symbols (NEG,N,-).

2. Do not make any connections to the carburetor, fuel lines, or thin metal parts.

3.  Identify if you have a negative or positive grounded vehicle. This can be done by on Mag-post (NEG or POS) is connected to the chassis.

4. For a negative grounded vehicle (most common): connect the RED POSITIVE jumper clamp the positive battery terminal, then connect the BLACK
   NEGATIVE jumper clamp to the negative battery terminal or vehicle chassis.

5. For a positive grounded vehicle (very uncommon): connect the BLACK NEGATIVE jumper clamp first to the negative battery terminal, then connect the RED POSITIVE jumper clamp to the positive battery terminal or vehicle chassis.

6. When disconnecting, disconnect in the reverse sequence, removing the negative first (or positive first for positive ground systems).

Jump starting

1. This unit is only for emergency use, not for frequent commercial use! ENGINE START socket is ALWAYS activated! Do not attempt to jumpstart your vehicle when the device battery capacity is below 20% (observe the battery status indicator on the unit).
2. Turn off the vehicle ignition and all accessories (radios, lights, air conditioners, etc.), and disconnect electronic devices.
3. Connect the jumper clamps to the correct polarity battery terminals.
4. Connect the ECS plug of jumper cables to the ENGINE START socket of the device.
5. Try starting the vehicle (turn on the ignition switch). Most vehicles will immediately start. Stop if the vehicle does not start after 5 seconds of engine cranking. The jump-start feature is designed for short-term operation only, and more than 5 seconds may cause damage to the unit. Allow the jump starter to cool down for at least 3 minutes after each jumpstarting.
6. Disconnect the cable from the device immediately after the engine starts, and then re- move from battery terminals.

Charging
This product is partially charged by the manufacturer. Fully charge the unit immediately after purchase. In order to prolong the product life, be sure to fully recharge the unit after each jumpstarting, or every 3 months even if this unit has not been used. If battery voltage in the Device is too low, this item will shut off to prevent damage to itself. Recharge the unit as soon as possible to be activated and fully charge it to ensure long battery life. In addition, we recommend not to charge and discharge the unit at the same time.
AC Charging:

1. Insert AC charging adapter into the charging jack of the unit.
2. Plug the other end of AC charging adapter into a wall socket.
3.  Fully charge the unit.
4. When charging is complete, unplug the AC charging adapter from the wall socket first, then from the charging jack on the Device.

DC Charging in Your Vehicle:

1. Turn the vehicle engine on.
2. Insert the DC charging adapter into the charging jack of the unit.
3. Plug the other end of the DC charging adapter into the vehicle’s cigarette lighter socket.
4. Fully charge the unit. The engine must keep running during the entire charge.
5. When charging is completed, unplug the OC charging adapter from the vehicle first, then from the charging jack on the Device.

Charging Time:
LCD will show “100%” as fully charged. Charging time will differ based on the discharge level and the power source used. If charging begins from 5% to full charge, it approximately takes 5 hours for AC charging.
USB Power
Connect the USB device to the device with a city tirl cable or the included multi-tip cable (better use the original cable of Apple® for Apple® products).
Press the Power button to start USB power, and@fes 0 quit. When disconnected, the device will automatically shut off. The number of times you can recharge a USB device will vary between
Flashlight
Press the Power button for 3 seconds to start the flashlight. sd Eet0y itch lilting modes: Steady On — Strobe — SOS — Off. ”

WWW.BORMANNTOOLS.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>