SEALEY TP6801.V3 Heavy-Duty High Flow Lever Pump User Manual
- June 3, 2024
- SEALEY
Table of Contents
HEAVY-DUTY HIGH FLOW LEVER PUMP
MODEL NO: TP6801.V3
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
SAFETY
WARNING! Ensure health & safety, local authority, and general workshop
practice regulations are strictly adhered to when using this equipment.
Familiarise yourself with product application and limitations, as well as the
specific potential hazards peculiar to this product.
Maintain the pump in good condition (use an authorised service agent).
Replace or repair damaged parts. Use genuine parts only. Non authorised parts
will invalidate the warranty.
Use only to pump NON-Corrosive fluids such as oil, anti-freeze, degreasants,
solvents, agricultural and industrial chemicals.
Ensure safety eye protection and protective clothing are worn when using this
product.
Keep the work area clean, uncluttered and ensure there is adequate lighting.
Maintain correct balance and footing. Ensure the floor is not slippery and
wear non slip shoes.
Keep children and unauthorised persons away from the working area.
Dispose of waste liquids in accordance with local authority regulations.
DO NOT use to extract corrosive fluids.
DO NOT dismantle, tamper with or adapt the pump for any purpose other than for
which it is designed.
DO NOT use the unit if it has been dropped or mishandled, check the unit to
ensure there is no damage.
DO NOT use the pump as a handle to move the fluid drum.
Keep the pump clean and store in a safe dry, childproof location.
WARNING! DO NOT allow uncontrolled discharge of fluids thus polluting the
environment.
INTRODUCTION
Steel barrelled, self-priming lever pump. Supplied with 2″BSP adaptor and dip tube suitable for 50 to 205L drums. Suitable for oils, antifreeze, degreasers and other non-corrosive fluids. High flow unit delivers approximately 400ml per stroke. Supplied with two delivery nozzles, one standard swan neck and one acute angle with filter for removing impurities from fluids.
OPERATION
- Attach the required discharge spout (fig.1, fig.2) to the pump ensuring that seal between spout and pump body is correctly fitted.
- Screw the suction tube into the underside of the pump, attach extension tube with seals as required (fig.3).
- Insert the pump into the 2″ BSP drum opening and hand tighten.
- Pump handle up and down to dispense liquid.
MAINTENANCE
- Ensure all liquid is removed from pump before storage.
- Clean out pump before using on other liquids.
- Store in a safe dry, childproof location.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice. Please note that other versions of this product are available.
If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk
or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
| 01284 757500| | 01284 703534| |
sales@sealey.co.uk| |
www.sealey.co.uk
---|---|---|---|---|---|---|---
© Jack Sealey Limited
Original Language Version
TP6801.V3 Issue 1 12/07/21
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>