CyberPower CSB404 4-Outlet Surge Protector User Manual

: June 3, 2024
: CyberPower

Table of Contents

OVERVIEW
FEATURES
SPECIFICATIONS
CAUTION
- TO REDUCE THE RISK OF ELECTRIC SHOCK:
TROUBLESHOOTING
FOR MORE INFORMATION
TECHNICAL SUPPORT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CyberPower CSB404 4-Outlet Surge Protector

CSB404 4-Outlet Surge Protector

OVERVIEW

CSB404 4-Outlet Surge Protector

FEATURES

ON/OFF Reset Control Switch and Circuit Breaker
Controls power to all outlets. The switch is also a 15A breaker. When an overload occurs, it will automatically switch on. To resume operation, ensure the overload condition is removed and reset the surge protector by switching the unit ON.
Standard Grounded Outlets (4)

SPECIFICATIONS

Model Number:	CSB404
Outlets:	4 Standard Grounded Outlets
Surge Protection:	450 Joules
Electrical Rating:	125 V/ 15 A / 1875 W
UL Clamping Voltage:	UL 1449 4th / 500 V (H-N, H-G, N-G)
Maximum Peak Current:	22,500 A
3 AC Lines Protected:	H-N: 7,500 A, H-G: 7,500 A, N-G: 7,500 A (The maximum

surge possible on household wiring is 6,000 volts)
Response Time:| Less than 1 nanosecond
Attenuation:| Up to 43 dB
EMI/RFI Filtration:| 150 kHz to 100 MHz
Circuit Breaker:| Resettable 15 Amp

WARNING: This product can expose you to chemicals including bisphenol (BPA) and styrene (ABS), which is known to the State of California to cause reproductive harm and cancer. For more information, go to www.P65Warnings.ca.gov.

CAUTION

TO REDUCE THE RISK OF ELECTRIC SHOCK:

Use only in dry locations and only indoors.
DO NOT plug into another relocatable power tap.
DO NOT “daisy chain” surge protectors.
DO NOT use with any aquarium equipment.
DO NOT use if properly grounded outlets are not available.
DO NOT install this device if there is less than 10 meters (30 feet) of wire between the electrical outlet and electrical service panel.
DO NOT use for medical or life support equipment. This device features an internal protection that will disconnect the surge protective component at the end of its useful lifeX, but it will maintain unprotected power to the load.

TROUBLESHOOTING

If the ON/OFF is switched off, the 15A circuit breaker may have tripped. Examine your connected equipment and remove the device that is overloading the circuit. Then, turn the ON/OFF switch back to RESET.

FOR MORE INFORMATION

Visit CyberPowerSystems.com for more information regarding:

Product information and certifications
Product warranty
Connected equipment guarantee

TECHNICAL SUPPORT

Visit:CyberPowerSystems.com/support
Toll-Free: 1-877-297-6937
© 2022 Cyber Power Systems (USA), Inc. All rights reserved.
All other trademarks are the property of their respective owners.

CONFORMANCE APPROVALS
**** This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.