FNIRSi HS-01 Intelligent Electric Soldering Iron User Manual

FNIRSi HS-01 Intelligent Electric Soldering Iron

Instrument Description

The HS-01 electric soldering iron consists of:

• Pen cover
• Pen body
• Soldering iron tip
• Locking nut
• Silica gel
• OLED screen
• Type-c interface power supply

Parameter

The HS-01 electric soldering iron has the following parameters:

• Power: 65W
• Screen: 0.87-inch OLED screen
• Operating voltage: DC9-20V
• Temperature range: 80-420°C
• Fast charging supply: USB Type-c port
• Protocol: PD trigger

Power selection

The HS-01 electric soldering iron can be set to obtain any operating voltage of 9V12V1520V from the adapter using the power adapter of the PD fast charging protocol. The default setting is 20V. Under different operating voltages, the working current, power, and tinning time are as follows:

If the voltage is lower than 9V, the screen will display low voltage. The default operating voltage of the Intelligent soldering iron is 20V. If the maximum output voltage of your adapter is less than 20V, the maximum output voltage will NOT be obtained. If your adapter outputs up to 12v, get 12V. When the power adapter without PD fast charging protocol is used, the operating voltage of the intelligent soldering iron is the input voltage. It is noted that when the adapter is connected and the heating will restart after entering the home page. This indicates that the output power of the adapter is not sufficient for the adapter, please replace another adapter.

Product Usage

Installation Instructions

1. Remove the nut.
2. Insert the soldering iron tip.

User Notice

• Please read this user manual and operating instructions carefully, and abide by the stipulations in the text.
• Please keep this manual properly.
• Discarded instruments cannot be disposed of together with household waste, please dispose according to relevant national or local laws and regulations.
• When there are any quality problems or questions about the use of the instrument, you can contact the online customer service of “Fnirsi-FNIRSI” or the manufacturer,and we will solve them as soon as possible.
• Thank you for purchasing this product. In order to make it more convenient for you to use this product, please follow this instructions.

Products Overview

HS-01 is a portable screen display intelligent electric soldering iron launched by our company. The electric soldering iron has the following characteristics:

• Small and convenient, easy to carry.
• Precise temperature control.
• Fast temperature recovery and rapid temperature rise.
• 9-20V operating voltage.
• Built-in OLED screen display.
• Type-c interface power supply.
• Ergonomic design, comfortable grip.

Instrument Description

Parameter

Power selection

Using the power adapter of the PD fast charging protocol, the intelligent electric soldering iron can be set to obtain any operating voltage of 9V\12V\15\20V from the adapter.(The default seting is 20V). Under different operating voltages, the working current, power and tinning time are as follows:

Notice

• The default operating voltage of the Intelligent soldering iron is 20V. If the maximum output voltage of your adapter is less than 20V, the maximum output voltage will NOT be obtained. If your adapter outputs up to 12v, get 12V.
• When the power adapter without PD fast charging protocol is used, the operating voltage of the intelligent soldering iron is the input voltage.It is noted that when the adapter is connected and the heating will restart after entering the home page. This indicates that the output power of the adapter is not sufficient for the adapter, please replace another adapter.
• If the output voltage of your adapter is 20V, but the output current is less than 3.25A(That is to say, the output power is less than the power required by the soldering iron), after entering the main interface and heating, the adapter may be powered off and restarted, which will cause the screen to restart!(Other operating voltages are the same)
• If it restarts after heating, it means that the output power of the current voltage of your adapter is not enough to work normally, Please select a lower working voltage according to the output power of the adapter.If your adapter output is 12V/2.5A, 15V/2A or 20/1.5A, the total output power is 30W,set the operating voltage to 12V.

Product Usage

Installation Instructions

• If it is found that the soldering iron is stuck when inserting, you can try to rotate it and insert it again.

Workflow Description

The working process of the HS-01 intelligent soldering iron is shown in the figure above.After power-on, the logo is displayed. Short press the corresponding flashing physical button once to heat up. When the child lock mode is turned on, short-press the corresponding physical button three times to heat. Entering the main interface, you can choose between 3 main working states of the soldering iron:

• Working state: The soldering iron is in a heated or ready-to-use state, please do not touch the high-temperature parts.
• Sleep state: The soldering iron is already in the state of heating and use, and it will enter into a sleep state if it is not used for more than the sleep time, and it will be released after use.
• Shutdown state: It will shut down when the power is disconnected.

Home page description

The home page is shown on the right, the lower right corner shows the target temperature set by the user, and the middle is the real-time temperature of the soldering iron. The bottom shows the heating power, and the upper right shows the operating voltage.

Operating Instructions

• Power on:Power on when connected to the power supply, the screen displays the boot icon, and then displays a prompt to insert the soldering iron tip, The interface will be displayed after the soldering iron tip is inserted .
• Heating: The icon button will flash, then short press the corresponding physical button to enter the heating page 2 8 0 , and the soldering iron will heat up.
• One-key standby： one presses the right button on the heating page to turn off the heating and return to the standby page .
• Temperature setting: In the heating page state, press the left and right keys to enter the temperature setting page to set the temperature, short press the right button to add a step value, short press the left button to decrease a step value. Long press to increase or decrease quickly, the step is 10°C or 20°F.
• Setting mode:In the non-temperature setting page, press and hold the left and right keys at the same time to enter the setting Vmool Steel .
• Screen brightness:In the setting mode, short press the left and right keys to switch to brightness long press the right key to enter , and the left and right keys adjust, and long press any key to exit.
• Temperature calibration: When entering the setting mode, short press the left and right keys to switch to the temperature calibration , long press the right keys to enter , the left and right keys to adjust, and long press any key to exit. Under the home page, set the target temperature as 350 ℃. After the temperature is stable, use the soldering iron thermometer to measure the actual temperature, record the difference between the target temperature and the actual temperature (positive or negative), and fill the difference into this item in the menu.
• Temperature unit: In the setting mode, short press the left and right keys to switch to the temperature unit , long press the right key to enter , ℃ F and the left and right keys switch, and long press any key to exit.
• Sleep time: In the setting mode, short press the left and right keys to switch to the sleep time , and long press the right key to enter , Left and right keys to adjust, after the adjustment is completed, long press any key to exit. The default sleep time is 20 minutes, and the setting range is 1-20 minutes. When it is set to the maximum, short press to turn off the sleep.
• Sleep temperature: In the setting mode, short press the left and right keys to switch to the sleep temperature , long press the right key to enter , and adjust the left and right keys. After the adjustment is completed, long press any key to exit. When the working temperature is lower than the sleep temperature, the working temperature is maintained in the sleep state, and when the working temperature is higher than the sleep temperature, the temperature will drop to the sleep temperature in the sleep state.
• Child lock mode: In the setting mode, short press the left and right keys to switch to the child lock mode , long press the right key to enter , switch left and right, and long press any key to exit after the switch is completed. After the child lock mode is turned on, when the power is turned on again, the button with a lock icon will be displayed . At this time, it is necessary to press the left button 3 times continuously to heat up.
• Language selection: In the setting mode, short press the left and right keys to switch to language selection , long press the right key to enter, switch left and right, and long press any key to exit when the switch is complete.
• Handheld mode: In the setting mode, short press the left and right buttons to switch to the handheld mode , long press the right button to enter , switch left and right, and long press any key to exit after switching is complete. The product is right-handed by default and can be set according to your own usage habits. The logic of switching to the left hand is reversed.
• Voltage gear: In the setting mode, short press the left and right tons to switch to the voltage gear type , long press the right button to enter , and after entering, switch left and right to the four voltage gears of 9V/12V/15V/20V, after the switch is completed, the long press any button to exit, the default is 20V, and the customer can set it according to the power parameters of the charger to avoid the phenomenon that the charger starts over-current protection due to insufficient power, and the device is forced to shut down with a black screen. When this phenomenon occurs, just wait for the charger to recover, and enter the setting page to re-select the appropriate gear when there is no heating or no soldering iron tip.
• The product will automatically shut down after 30 minutes of inactivity in the dormant state

Firmware upgrade

• The device is powered off, press the left button, use the USB Type-c data cable to connect the computer to power on the device, and enter the Bootloader interface to upgrade the firmware.
• Choose the corresponding serial port number, open the selected file when ready is displayed on the left, and click to burn.

Maintenance

• When a new soldering iron tip is used for the first time, it needs to be heated to 250°C and tinned to prevent dry-burning oxidation.
• The new soldering iron has the problem of the temperature jumping for the first time, and it will be stable after several times of use.
• After using the soldering iron, please apply an appropriate amount of solder to the tip of the soldering iron to prevent oxidation.
• The normal working temperature of the soldering iron tip is about 300-380°C, please don’t use it for a long time if the temperature is too high to affect its life.
• Avoid hitting the soldering iron head violently during welding.
• Do not use wet sponge with clear water, a semi-dry state is best.
• Do not use scaling powder with high chlorine or acid to avoid corroding the surface.
• If the surface of the soldering iron tip is oxidized and does not stick to tin, use gauze or other tools to carefully wipe the surface layer, then heat it up to 250 ℃, and immediately apply tin to stick the surface to prevent re-oxidation.

Safety Instructions

• The temperature of the soldering iron tip can reach 80-420°C, please do not touch the soldering iron tip.
• Please keep out of reach of children.
• Please do not get this product wet, or use it in a humid environment.
• When not in use for a long time, please disconnect the power.
• When working normally, there will be a certain temperature at the handle, which is a normal phenomenon, please use it with confidence!

Warranty terms

• Service period
• Shenzhen Finiris Technology Co., Ltd. promises good quality of the product. If the product fails under normal use within 7 days from the date of sale,the customer can choose to return or warranty (it can only be returned without affecting the second sale).There is a free warranty for failures within the year.
• The date of purchase is subject to the date of purchase invoice or receipt issued by the seller. For online purchases, the screenshot of the transaction shall prevail.
• For the following cases, no free warranty service is provided

1. All damage to the machine is caused by man-made damage, unauthorized modification or maintenance.
2. Soldering iron tips are consumables and do not support a warranty.

Contact US

• Any FNIRSI users with any questions who come to contact us will have our promise to get a satisfactory solution + an Extra 6-Month Warranty thanks for your support!
• By the way, We have created an interesting community, welcome to contact FNIRSI staff to join our community.
• Shenzhen FNIRSI Technology Co., LTD.
• Add.： West of Building C, Weida Industrial Park, Dalang Street, Longhua District, Shenzhen, Guangdong
• E-mail： fnirsiofficial@gmail.com (Business) / fnirsiofficialcs@gmail.com(Equipment service)
• Tel： 0755-83242477 / +8613536884686

www.fnirsi.cn

References

• 菲尼瑞斯科技

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>