Aladdin BI-FABRIC 2 Flexible Light User Manual
- June 3, 2024
- ALADDiN
Table of Contents
Aladdin BI-FABRIC 2 Flexible Light
START-UP GUIDE
| 1 | Connector |
|---|---|
| 2 | Metal ring for mounting (can be attached to magnets) |
| 3 | Velcro |
| 4 | Metal corner (can be attached to magnets) |
Unpack your panel and accessories from the kit. Plug in the panel connetor to
your dimmer-unit. Use the extansion in between if needed. IPlug in your
dimmer-unit to a power outlet. Instead of using the power outlet, there’s an
integrated V-Mount or Gold-Mount plate on top of the dimmer. You can use
batteries from 12-30V DC.
Just note that you need batteries which can handle the power draw of 100 watts
from the panel. There’s a simple calculation for that:
If you are using 14.8V batteries you need at least a working current of 6.8A. If your battery is rated at 14.8V and 100Wh/6.8Ah with a working current of 6.8A you can run your BI-FABRIC 2 for one hour. For any further questions about using our products please refer to our cus-tomer service or watch the instructional videos on www.aladdin-lights.com or YouTube.
IMPORTANT CAUTIONS AND WARNINGS
- Do not use near flammables and heaters.
- Do not expose the unit to direct sunlight for a long period (applies also for storing in a car).
- Do not use the dimmer wire or extension wire to hang or mount the panel.
- Do not bend or fold the panel more than 90 degrees.
- Do not tape directly on the LEDs of the panel – they can burn out.
- Do not damage the product with improper force or cause any impact with heavy objects.
- Do not cut the panel with sharp objects.
- Keep out of reach of children.
- The panel will heat up when running a long period of time on 100% pow-er, make sure to have it in your eyesight at all times. Use the X-BEND holder or frame to assure enough air flow for heat reduction.
- Use the product only within the temperature range of -10°C – +40°C.
- Make sure the panel has cooled down before storing it in the pouch or any other case.
- When you have technical problems while using the product, stop using it immediately and contact your dealer/reseller.
WARRANTY
We provide a one year warranty period after the purchase. This warranty covers repairs or a replacement for faulty products within this period. After this warranty has been expired, you can still get repairs for your product which will be charged extra. Aladdin Lights reserves the right to refuse warranty service on products un-der disputable conditions.
WARRANTY EXCLUSIONS
In case of any of the below listed causes, the warranty does not apply, even if it is within the free warranty period.
- Product failure due to consumer negligence.
- Product failure due to usage of not compatible power sources.
- Product failure due to disassembly by not official resellers/distributors.
SELECTED OPTIONAL ACCESSORIES
TECHNICAL SPECIFICATIONS
| Light source | 100W Bi-Color LEDs |
|---|---|
| CRI | Ra 97 |
| TLCI | 98 |
| Color temperature | 2850K – 6098K |
| Beam angle | 140° |
| Dimmer | Dimming: (1%–100%) |
| Cooling | Passive cooling |
| Dimmer input | 12V to 24VDC |
Power unit input
| ****
Automatic voltage 100V to 240VAC
Power consumption| 100W
Dimensions
| 600mm (W) x 300mm (H) x 18mm (D) (w/ built- in dimmer)
Weight| 306g
Connection| Connector plug
Temperature range| -10°C – +40°C
DMX512 support| With dimmer unit
DMX512| 2 Channels – White Bi-Color
Material| Fabric
IP-Rating| 32
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>