AURORALIGHT IGR331203 Fixed Aim,In Grade Luminaire Installation Guide
- September 27, 2024
- auroralight
Table of Contents
- IGR331203 Fixed Aim,In Grade Luminaire
- Product Information
- Specifications:
- Installation Steps for Underground Fixture:
- Installation Steps for Conduit Fixture:
- Required Tools:
- Q: What should I do if I encounter resistance while sliding the
- Q: Can I use a different type of gravel for backfilling around
IGR331203 Fixed Aim,In Grade Luminaire
“`html
Product Information
Specifications:
- Model: IGR331203
- Power Supply: Low voltage
- Materials: PVC Sleeve, Pea Gravel, UL Listed Wire Connectors,
12GA Underground Supply Cable, 18GA Lead Wires
Product Usage Instructions
Installation Steps for Underground Fixture:
-
Disconnect transformer from the electrical supply and ensure
power is off. -
Prepare a hole 8 inches deep to accommodate the 3 PVC
Sleeve. -
Fill the hole with pea gravel for drainage and a stable
base. -
Feed the 12GA underground cable into the PVC Sleeve placed in
the hole. -
Connect the 18GA lead wires to the underground cable using UL
listed connectors. -
Slide the fixture into the collar ensuring it sits level and
plumb. -
Backfill with pea gravel and soil until only the faceplate is
visible. -
Remove handle after installation is complete.
Installation Steps for Conduit Fixture:
-
Disconnect transformer from the electrical supply and ensure
power is off. -
Prepare a hole 8 inches deep to accommodate the PVC Sleeve with
Conduit Plate. -
Attach your wire conduit to the PVC Sleeve placed in the
hole. -
Feed your main supply cable into the PVC Sleeve leaving enough
excess for connections outside. -
Backfill with pea gravel ensuring the collar is at finish grade
level.
Required Tools:
- 3/32 Allen Key (Included)
- Wire Cutter / Stripper
- Shovel (For Underground Installation)
- Philips Head Screwdriver (For Conduit Installation)
FAQ
Q: What should I do if I encounter resistance while sliding the
fixture into the collar?
A: Double-check the alignment and make sure the fixture is
positioned correctly before attempting to slide it in. Avoid
forcing it to prevent damage.
Q: Can I use a different type of gravel for backfilling around
the fixture?
A: It is recommended to use pea gravel as it provides adequate
drainage and stability. Using a different type of gravel may affect
the performance of the fixture.
“`
CENTRO INSTALL GUIDE
IGR331203
INSTRUCTIONS: 1. To prevent electrical shock, disconnect transformer from
electrical supply and make sure power supply is completely off before
installation. Fixtures should always be installed by a licensed electrician.
2. Prepare a hole large enough to accommodate the 3″ PVC Sleeve,
approximately 8″ deep.
3. Fill the bottom of the hole with pea gravel for water drainage and a
secure base. Lightly pack it down in the hole.
4. Feed the 12GA underground supply cable into the PVC Sleeve then place it
in the hole. Top of collar should be at finish grade height and it should sit
level.
5. Connect the 18GA lead wires to 12GA underground supply cable using UL
listed connectors suitable for underground burial or wet location (see figure
for configuration).
6. Neatly place excess wire and the connectors in the PVC Sleeve then slide
the fixture into the collar until it stops. The fixture should be plumb and
the faceplate flush with the surrounding landscape (see figure).
7. Back fill the area around the fixture with pea gravel and lightly pack it
in/down. Fill any remaining area with soil until the faceplate is the only
thing visible.
8. The handle is used to aid in installation and removal of the fixture from
the sleeve. When finished, remove the handle screws and handle. Screw the
handle screws into the faceplate and keep the handle elsewhere for future use.
REQUIRED TOOLS:
3/32 Allen Key (Included) Wire Cutter / Stripper Shovel
HANDLE SCREW
18GA LEAD WIRE COLLAR
HANDLE FIXTURE FINISH GRADE
UL LISTED WIRE CONNECTOR
LANDSCAPE PVC SLEEVE PEA GRAVEL
12GA LISTED SPT 3 UNDERGROUND CABLE
TIP: Small gauge cable is vulnerable to damage in the landscape; Protect by routing in close proximity to the luminaire or adjacent to concrete slab or similar structure. Do not over tighten.
P. 760.931.2910 E. techsupport@auroralight.com O. 2742 Loker Ave. W Carlsbad CA 92010 W. www.auroralight.com
WARNING: Luminaire must be
installed in accordance with local
codes and the National Electrical
Code (NEC). Failure to do so may result in serious injury and or damage to the
luminaire.
WARNING: Risk of electric
shock. Install per NEC Code 680.22(B (6), if listed low voltage luminaires are
to be
located near a pool, spa or fountain.
CENTRO INSTALL GUIDE (Conduit)
IGR331203
REQUIRED TOOLS:
Wire Cutter / Stripper Philips Head Screwdriver
INSTRUCTIONS: 1. To prevent electrical shock, disconnect transformer from
electrical supply and make sure power supply is completely off before
installation. Fixtures should always be installed by a licensed electrician.
2. Install the ½” conduit adapters into the back of the Conduit Plate by
removing any plugs and threading in.
For Landscape Installation:
3. Prepare a hole large enough to accommodate the 3″ PVC Sleeve,
approximately 8″ deep. Place the PVC Sleeve with Conduit Plate into the hole
and attach your wire conduit.
4. Feed your main supply cable into the PVC Sleeve, leave enough excess to
make a wire connection with the fixture outside of the PVC Sleeve (see
figure).
HANDLE SCREWS
18GA LEAD WIRE COLLAR
5. Back fill the area around the fixture with pea gravel and lightly pack it
in/down. The top of collar should be at finish grade level (see figure).
Continue to step #5 below.
For Concrete Installation:
UL LISTED WIRE CONNECTOR
MAIN SUPPLY CABLE
HANDLE
FIXTURE FINISH GRADE
LANDSCAPE PVC SLEEVE PEA GRAVEL, STONE OR CONCRETE
3. Secure the PVC Sleeve with Conduit Plate and connect your wire conduit.
Ensure it will not move during the concrete pour.
4. Plug any unused holes/openings so wet concrete doesn’t enter the PVC
Sleeve, then pour concrete and let it cure. The top of the collar should be
flush with finish grade height (see figure).
5. Connect 18GA lead wires to Main supply cable using UL listed connectors
suitable for the location. Place excess wire and connectors in the PVC Sleeve
then slide the fixture into the collar until it stops. Faceplate should be the
only thing visible.
6. The handle is used to aid in installation/removal of the fixture from the
sleeve. When finished, remove handle screws and handle. Screw the handle
screws into the faceplate and keep handle elsewhere for future use.
CONDUIT PL ATE CONDUIT ADAPTER WIRE CONDUIT
TIP: Small gauge cable is vulnerable to damage in the landscape; Protect by
routing in close proximity to the luminaire or adjacent to concrete slab or
similar structure. Do not over tighten.
P. 760.931.2910 E. techsupport@auroralight.com O. 2742 Loker Ave. W Carlsbad CA 92010 W. www.auroralight.com
WARNING: Luminaire must be
installed in accordance with local
codes and the National Electrical
Code (NEC). Failure to do so may result in serious injury and or damage to the
luminaire.
WARNING: Risk of electric
shock. Install per NEC Code 680.22(B (6), if listed low voltage luminaires are
to be
located near a pool, spa or fountain.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>