AURORALIGHT PTA008105 Meridian 16 Inch Pathlight Installation Guide

September 16, 2024
auroralight

PTA008105 Meridian 16 Inch Pathlight

“`html

Product Information

Specifications:

  • Model: PTA008105
  • Power Supply: Low Voltage
  • Wire Gauge: 18GA lead wires
  • Required Tools: 3/32 Allen Key, Heavy Mallet/Hammer, Wire
    Cutter/Stripper

Product Usage Instructions:

  1. Disconnect transformer from electrical supply and ensure power
    is off before installation.

  2. Pound the ground stake fully into the soil making sure it is
    plumb.

  3. Feed the 18GA lead wires through the ground stake and out of
    the lead wire exit hole.

  4. Connect the 18GA lead wires to a 12GA underground supply cable
    using UL listed connectors suitable for burial or wet
    locations.

  5. Use SPT-3 Underground Low Energy Cable for power supply to the
    luminaire.

  6. Route small gauge cables close to the luminaire or adjacent to
    a structure to avoid damage; do not bury more than 6 inches
    deep.

  7. Follow local codes and NEC regulations for installation to
    prevent injury or damage.

FAQ:

Q: Can I install the luminaire near a pool, spa, or

fountain?

A: Yes, you can install near water features, but ensure to
follow NEC Code 680.22(B (6) for listed low voltage luminaires.

Q: What type of cable should be used for the underground

supply?

A: Use SPT-3 Underground Low Energy Cable listed for such
use.

Q: What precautions should I take during installation?

A: Always disconnect power, use proper tools, secure connections
with UL listed connectors, and follow recommended burial depths and
routing guidelines.

“`

MERIDIAN INSTALL GUIDE
PTA008105

INSTRUCTIONS: 1. To prevent electrical shock, disconnect transformer from
electrical supply and make sure power supply is completely off before installation. Fixtures should always be installed by a licensed electrician.
2. Pound the ground stake fully into soil, stake should be plumb.
3. Loosen the set screw with the supplied Allen key and remove the ½” adapter from the stem assembly. Screw the ½” adapter into the ground stake and tighten down by hand.
4. Feed the 18GA lead wires through the ground stake and out of lead wire exit hole (see figure).
5. Slide the stem assembly into the ½” adapter until it fully stops. Tighten the set screw down to secure in place.
6. Separate the 2-conductor 18GA lead wires by pulling apart the ends approximately 10″. Strip about ½” of the insulation off the ends (see figure).
7. Connect the 18GA lead wires to 12GA underground supply cable using UL listed connectors suitable for underground burial or wet location (see figure for configuration).
8. Underground supply cable for power supply to this luminaire shall be SPT-3 Underground Low Energy Cable and listed as such (see figure).

FINISH GRADE WIRE EXIT HOLE UL LISTED WIRE CONNECTOR 12GA LISTED SPT-3 UNDERGROUND CABLE 18GA LEAD WIRE

REQUIRED TOOLS:
3/32 Allen Key (Included) Heavy Mallet/Hammer Wire Cutter / Stripper
STEM ASSEMBLY
SET SCREW 1/2″ ADAPTER GROUND STAKE

P. 760.931.2910 E. techsupport@auroralight.com O. 2742 Loker Ave. W Carlsbad CA 92010 W. www.auroralight.com

TIP: Small gauge cable is vulnerable to damage in the landscape; Protect by routing in close proximity to the luminaire or adjacent to concrete slab or similar structure. Do not bury more than 6″ deep. Do not over tighten.

WARNING: Luminaire must be
installed in accordance with local
codes and the National Electrical
Code (NEC). Failure to do so may result in serious injury and or damage to the luminaire.

WARNING: Risk of electric
shock. Install per NEC Code 680.22(B (6), if listed low voltage luminaires are to be
located near a pool, spa or fountain.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

auroralight User Manuals

Related Manuals