AURORALIGHT MNL650108 Artemis Luminaire Installation Guide
- September 14, 2024
- auroralight
Table of Contents
AURORALIGHT MNL650108 Artemis Luminaire
Specifications
- Model Numbers: MNL650108, MNL650211
- Tools Required: 3/32 Allen Key, Wire Cutter/Stripper
- Connectors: UL Listed Wire Connector
General Installation Instructions
- To prevent electrical shock, disconnect the transformer from the electrical supply and make sure the power supply is completely off before installation. Fixtures should always be installed by a licensed electrician.
- Secure the mount in the desired location and thread in the mount loop (see figure).
- Loop the safety cable through the mounting loop and feed it back through the cable clamp with about a 1” tail protruding from the other side (see figure).
- Tighten the set screw down thoroughly on the safety cable using the provided Allen key and ensure it will not easily slip through the cable clamp.
- Feed the fixture lead wire through the mount loop. If accessible, tie the fixture lead wire into an overhand knot to reduce strain on the wire connections (see figure).
- Strip the outer insulation off the end of the 2-conductor fixture lead wire to separate them, then strip about ¼” of insulation off each conductor.
- Connect the fixture lead wire to the main supply cable using UL-listed wire connectors suitable for the location.
- neatly secure all electrical wiring in a desired area.
WARNING: Luminaire must be installed by the local codes and the National
Electrical Code (NEC). Failure to do so may result in serious injury and or
damage to the luminaire.
WARNING: Risk of electric shock. Install per NEC Code 680.22(B (6), if
listed low voltage luminaires are to be located near a pool, spa, or fountain.
REQUIRED TOOLS
- 3/32 Allen Key (Included)
- Wire Cutter / Stripper
ARTEMIS INSTALL GUIDE (Tree mount)
MNL650108 / MNL650211
- To prevent electrical shock, disconnect the transformer from the electrical supply and make sure power supply is completely off before installation. Fixtures should always be installed by a licensed electrician.
- Secure the fixture lead wire around a tree branch or other desired location by wrapping it several times or fastening it in a manner that will not cause damage to the wire (see figure).
- Loop the safety cable around a secure location and feed it back through the cable clamp with about a 1” tail protruding from the other side (see figure).
- Tighten the set screw down thoroughly on the safety cable using the provided Allen key and ensure it will not easily slip through the cable clamp.
- Strip the outer insulation off the end of the 2-conductor fixture lead wire to separate them, then strip about ¼” of insulation off each conductor.
- Connect the fixture lead wire to the main supply cable using UL listed wire connectors suitable for wet locations.
- Neatly secure all electrical wiring in a desired area.
WARNING: Luminaire must be installed by the local codes and the National
Electrical Code (NEC). Failure to do so may result in serious injury and or
damage to the luminaire.
WARNING : Risk of electric shock. Install per NEC Code 680.22(B (6), if
listed low voltage luminaires are to be located near a pool, spa or fountain.
Frequently Asked Questions
Q: What should I do if I encounter difficulty in tightening the set
screw?
A: Ensure you are using the provided Allen key correctly and applying
sufficient pressure while tightening the set screw. Q: Can I install the
fixture myself without a licensed electrician?
A: It is recommended to have a licensed electrician install the fixtures to
prevent any electrical hazards.
Q: How do I know if the wire connectors are suitable for wet locations?
A: Check the product packaging or consult with the manufacturer to verify if
the connectors are suitable for wet environments.
760.931.2910
E. techsupport@auroralight.com
O. 2742 Loker Ave. W Carlsbad CA 92010
W. www.auroralight.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>