AURORALIGHT STW636103, STW636203 Micro Cascade Installation Guide

September 27, 2024
auroralight

AURORALIGHT STW636103, STW636203 Micro Cascade

Product Information

Specifications

  • Model: STW636103 / STW636203
  • Tools Required: 3/32 Allen Key, Wire Cutter/Stripper, Philips Head Screwdriver, 3/4 Drill Bit
  • Manufacturer: Aurora Light
  • Contact: P. 760.931.2910 / E. techsupport@auroralight.com / O. 2742 Loker Ave. W Carlsbad CA 92010 / W. www.auroralight.com

Product Usage Instructions

  1. Electrical Safety: Before installation, disconnect the transformer from the electrical supply and ensure the power supply is completely off to prevent electrical shock. Always have fixtures installed by a licensed electrician.
  2. Assembly:
    • Loosen the set screws on the sides to remove the faceplate assembly from the back plate.
    • Center the back plate on the hole and secure it with screws (use anchors for stone or tile mounting).
    • Feed the main supply cable through the hole in the center of the back plate.
    • Connect the main supply cable to the fixture lead wires using Wago wire connectors.
    • Neatly place excess wire and connectors in the back plate and slide the faceplate assembly in until it stops.
    • Rotate the faceplate assembly to level it and tighten the set screws on the sides to secure it in place.

Tips: Small gauge cable should be protected from damage in the landscape by routing it close to the luminaire or adjacent to a concrete slab. Avoid over-tightening during installation.

Warnings:

  • Luminaires must be installed following local codes and the National Electrical Code (NEC) to prevent serious injury or damage.
  • Risk of electric shock exists. Install per NEC Code 680.22(B (6) if low voltage luminaires are near a pool, spa, or fountain.

FAQ

  • Q: Can I install the luminaire myself without a licensed electrician?
    • A: It is recommended to have fixtures installed by a licensed electrician to ensure safety and proper installation per local codes and regulations.

REQUIRED TOOLS

  • 3/32” Allen Key (Included)
  • Wire Cutter / Stripper
  • Philips Head Scr ewdriver
  • 3/4” Drill Bit

INSTALLATION INSTRUCTIONS

  1. To prevent electrical shock, disconnect transformer from electrical supply and make sure power supply is completely off before installation. Fixtures should always be installed by a licensed electrician.
  2. Remove the faceplate assembly from the back plate by loosening the set screws on the sides (see figure).
  3. Drill a ¾” to 1” hole into the mounting surface in the desired mounting location.
  4. Center the back plate on the hole and screw it down with the provided screws (use provided anchors if mounting in stone or tile).
  5. Feed your main supply cable through the hole and the center of the back plate (see figure).
  6. Connect the main supply cable to the fixture lead wires using the wago wire connectors (see figure).
  7. Neatly place excess wire and connectors in the back plate then slide the faceplate assembly in until it stops.
  8. Rotate the faceplate assembly until it is level then tighten down the set screws on the sides to hold it in place (see figure).

TIP: Small gauge cable is vulnerable to damage in the landscape; Protect by routing in close proximity to the luminaire or adjacent to concrete slab or similar structure. Do not over tighten.

WARNING

  • Luminaire must be installed in accordance with local codes and the National Electrical Code (NEC). Failure to do so may result in serious injury and or damage to the luminaire.
  • Risk of electric shock. Install per NEC Code 680.22(B (6), if listed low voltage luminaires are to be located near a pool, spa or fountain.

CONTACT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

auroralight User Manuals

Related Manuals