ZYXEL USG20-VPN Series SOP for Firewall Onboarding to Nebula User Guide
- June 4, 2024
- ZYXEL
Table of Contents
SOP for firewall
onboarding to Nebula
ATP/USG FLEX/USG20-VPN Series
User Guide
Powered by Zyxel Nebula
together we are connected
Nebula Together represents Zyxel’s strategy to help customers realize
thepower of bringing your whole network together into a single platform.
Install Hardware
-
Use the included power adaptor or power cord to connect the power socket (on the rear panel) to a power outlet.
-
It is recommended that you configure the security appliance before using it to protect your network. Use an Ethernet cable to connect a computer to the LAN port (P4) of the security appliance.
-
Use another Ethernet cable(s) to connect a computer to the WAN port (or P2, if no WAN label) to an Ethernet jack with Internet access. At the front panel, ensure that the PWR light turns on. The SYS light blinks during system testing and initialization, then it should stay on when the system is ready. We’ll get you quickly up and going with this guide for Zyxel firewall onboarding to Nebula with DHCP WAN type.
Run initial wizard and upgrade firmware
2.1 Login to device GUI with IP:
https://192.168.1.1
User name: admin
Password: 1234
2.2 Set up a new password.
2.3 Use the new password to
log in.
2.4. Start initial wizard and
click Next >
2.5 Connect to Internet(WAN):
Select “ Ethernet ” and choose “ Auto ”(DHCP) as the WAN type. If you
are using PPPoE, please select PPPoE.
2.6 Check the Connection
Test showing “OK” then press Next.
2.7 Data and Time Settings-
Click Sync. Now then press Next.
2.8 Firmware Upgrade – A new
firmware will upgrade automatically.
Onboard on Nebula Cloud
3.1 Go to Nebula Control Center page.
(https://nebula.zyxel.com) and click Get Started.
Create a Zyxel account. If
you already have a Zyxel account, please skip stepping 3.5.
3.2 Create a Zyxel account.
3.3 Check your email with a confirmation link and open the link.
3.4 Set your password
and 2FA.
If you would not like to
enable 2FA, please click Skip.
3.5 Click Let’s Start to set up Nebula’s initial wizard.
3.6 Create your
Organization and Site.
3.7 Don’t Skip this
step! Add your device’s MAC address and Serial Number and click + Add, then
click Next. (MAC address can be found on the sticker. When entering the MAC
address, the colons will automatically be added in.)
3.8 Click “Skip WiFi
Settings”.
3.9 Select DHCP as WAN
type and click Next. (If your WAN type is PPPoE, please select PPPoE). The
system will send you an installation email.
3.10 Click Go to Nebula
dashboard
3.11 Select “ Activate
one-month trial period “ and click OK.
IMPORTANT
3.12 Go to your inbox and check for a mail subject with“ Register your
Zyxel Firewall device_device model ”.
3.13 Press the reset
button for five seconds on the device.
3.14 Click “ Allow
Nebula to Manage My Device ”
3.15 Conduct the ZTP process.
3.16 Log in to NCC and
check the online appliance status.
Congratulations on
finishing your firewall setup on Nebula! Enjoy advanced protection with easy
management!
Documents / Resources
|
ZYXEL USG20-VPN Series SOP for Firewall Onboarding to
Nebula
[pdf] User Guide
USG20-VPN Series SOP for Firewall Onboarding to Nebula, USG20-VPN Series, SOP
for Firewall Onboarding to Nebula
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>