netis AC1200 Wireless Dual Band Router Installation Guide

netis AC1200 Wireless Dual Band Router

Product Information

This product complies with part 15 of the FCC Rules and has been tested to ensure that it does not cause harmful interference. The device is designed to accept any interference received, including interference that may cause undesired operation. This device has been tested and complies with FCC radiation exposure limits for an uncontrolled environment.

• Compliance : Part 15 of the FCC Rules
• Interference : This device may not cause harmful interference
• Acceptance : This device must accept any interference received, including interference that may cause undesired operation
• Radiation Exposure: Complies with FCC radiation exposure limits for an uncontrolled environment

Product Usage Instructions

To ensure compliance with FCC regulations and to avoid any potential harm, please follow these usage instructions:

1. Do not make any changes or modifications to the device that are not expressly approved by the party responsible for compliance. Doing so could void your authority to operate the equipment.
2. When using the equipment, maintain a minimum distance of 20cm between the radiator and your body. This will help ensure that you are not exposed to excessive radiation levels.
3. If you experience any interference or undesired operation while using the device, please contact the manufacturer for assistance.

Package Contents

• This QIG is for netis 11AX Dual Band router.
• The product model shown in this QIG is NX30, as an example.

LED Explanation

Hardware Connection

1. Power off your Modem.
2. Connect the WAN port on netis Router to the Modem’s LAN port with an Ethernet cable.
3. Connect your computer to one of the LAN ports on nets Router with an Ethernet cable.
4. Power on your Modem.
5. Plug the provided Power Adapter into the PWR jack of nets Router and the other end to a standard electrical socket. Then wait for one minute.

Configure the Router via the Web Management Page

1. Connect your PC to one of the LAN ports on the router with an Ethernet cable, or connect your WiFi device to the router’s default SSID.
   Default SSID: 2.4G SSID: Netis-XXXXXX/5G SSID: Netis-XXXXXX-5G (“XXXXXX”: Last 6 digits of LAN MAC)

2. Open your browser and type http://netis.cc or 192.168.1.1 in the address to visit the router’s web management page.

3. Enter the setup wizard to start configuring.
   Tip : You can select the language as you want is the top corner, default is English.

4. The router will detect your Internet access mode automatically.

5. If Dynamic IP(DHCP) is selected, the router will automatically receive the IP parameters from your ISP(Internet Service Provider).

6. If PPPoE is selected, please enter the User Name and Password provided by your ISP.

7. If Internet access mode isn’t detected automatically, please choose it manually.

8. If Static IP is required, please enter the IP Address/Subnet Mask/Default Gateway/DNS Servers provided by your ISP.

9. Configure your Wi-Fi name and password as you required and click “Save”.

10. Wi-Fi setting succeeded, you can surf the Internet now.

Easy Mesh

Method 1: Press the WPS button on each nets mesh router at the same time to configure the mesh connection automatically.

FCC

FCC PART 15.105 INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

PART 1519 COMPLIANCE INFORMATION:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation.

Caution!

• Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
• Operations in 5150-5250 MHz band is for indoor use only.

FCC Radiation Exposure Statement

• This equipment complies with fcc radiation exposure limits set forth for an uncontrolled environment.
• This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>