CLARION JM-KICK Party Speaker User Manual
- September 26, 2024
- clarion
Table of Contents
CLARION JM-KICK Party Speaker
Specifications
- Output power : 20W (RMS)
- Driver Units : 2 + 5.25
- Frequency response: 100Hz-20KHz
- Separation: 40 dB
- S / N: 55 dB
- Distortion: 1% (1K, 1W)
- Voltage/Frequency : DC 5V 2A
- Dimensions: W210 x D180 x H294 (mm)
DEAR CUSTOMER:
- Thank you for buying the product!
- Before first use, please read the manual carefully.
Operation explanation
Specifications
- Output power : 20W (RMS)
- Driver Units: 2″ + 5.25″
- Frequency response: 100Hz-20KHz Separation: ≥40 dB
- S / N: ≥55 dB
- Distortion: ≤1% (1K, 1W)
- Voltage/Frequency: DC 5V 2A Dimensions: W210 x D180 x H294 (mm)
Features
- Quality Speaker with built-in amplifier
- Full audio spectrum performances, ideal for your favorite entertainment from Mp3, Mp4, CD/DVD movies and digital playbacks.
- Quality materials : Only the best components to recreate sound faithfully across all frequencies.
Package contents
- Party speaker: 1 pc
- User manual: 1 pc
- Audio input cord : 1 pc
- TYPC-C charging cable: 1 pc
Top Panel
- : short press turn on, Long press to shut down when power on;
- Press the mode to switch when starting:
- BT: blue light, Quickly flashing when searching for a pair;
- Flash slowly when playing; Long bright when pausing.
- AUX: green light, Playtime bright; mute or pause the slow flash.
- USB: red light, Flash slowly when playing; light up when pausing.
- : Turn on/off the backing vocals.
- ECHO : Press the reverberation adjustment, and adjust the reverberation plus or minus with VOL.
- :Press play to pause or mute; Press twice. Next song.
- Press 3 times to play the previous song.
- 5. LOL+/-: Left and right rotation outer ring encoder main volume adjustment
- : Press the button to adjust the volume with VOL.
- : Tap indoor and outdoor sound to cycle to switch.
- : Short press light effect control.
After No signal in any mode or mute, pause for 15 minutes unit automatic shutdown
BT Pairing Method
Press “ ” button on the speaker’s top panel to go to Bluetooth mode, The Fifth indicator light starts to flash fast to search the Bluetooth device. Turn on your mobile Bluetooth device and search for the device name “SP525”, paired them well. When you have successfully paired your mobile to the speaker system, The Fifth indicator light is on. When starting to play your mobile music, The Fifth indicator light is flashes slowly. The functions as “PREVIOUS/ NEXT”, and “PLAY/PAUSE”, can operate via the top panel. On Bluetooth mode, when connecting with the mobile, press “ ” for 3 seconds, bluetooth function can be force-disconnected
Additional information
Automatic shutdown without signal for 15 minutes
After No signal in any mode or mute, pause for 15 minutes unit automatically
shuts down.
Memory
After shutdown or power off, and then boot, remember the following pre-
shutdown functions:
- Channel mode
- All volume levels
- Sound effects
- Bluetooth pairing and U disk playback
Low current detection function Battery level detection
“Beep” alarm when the battery level is detected at 20%. Automatically shutdown
when the battery level is detected at 10% .
Rear panel
- Micphone slot.
- Input Connect to sound sources such as computers, CD player, MP3, etc.
- USB slot.
- RESET: Press and hold the button at the back plate of the subwoofer, and connect to power at the same time, wait for 5 seconds, then stop pressing, The Subwoofer will be reset.
- DC Power cord.
Do NOT use USB for charging devices, as it is not designed for charging. Thank you.
FCC Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B Digital Device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
PLEASE NOTE: Do not leave objects generating magnetism near the speakers.
FAQ
- Q: What is the automatic shutdown feature?
- A: The unit will automatically shut down after 15 minutes of no signal in any mode or mute.
- Q: What functions are remembered after shutdown?
- A: The pre-shutdown functions remembered include channel mode, all volume levels, sound effects, Bluetooth pairing, and U disk playback.
- Q: What is the low current detection function?
- A: The unit has a battery level detection feature that triggers a beep alarm at 20% battery level and automatically shuts down at 10% battery level.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>