OHLINS HD 513 Softail Shock Absorber Instruction Manual
- September 26, 2024
- OHLINS
Table of Contents
OHLINS HD 513 Softail Shock Absorber
Specifications
- Part No: HD 513
- Contents: 1x HD 513, 5x 00231-01, 1x 01082-11, 3x 05404-07, 3x 00430-02, 6x 00153-04, 1x 10207-01, 1x 07241-02
FAQs
- Q: What should I do if there are small differences between my product and the images in the instructions?
- A: Small differences are normal. Refer to the text instructions for accurate assembly guidance.
- Q: How should I handle oil or grease leaks during storage or transport?
- A: Wipe off excessive oil or grease with a cloth. It will not damage the product.
Kit Contents
| Description | Part No | Pcs |
|---|---|---|
| Shock absorber | HD 513 | 1 |
| Tie-rap | 00231-01 | 5 |
| Bracket | 01082-11 | 1 |
| Screw M6x30 | 05404-07 | 3 |
| Nut | 00430-02 | 3 |
| Washer | 00153-04 | 6 |
| Sticker set Öhlins | 10207-01 | 1 |
| Owner´s Manual Road & Track | 07241-02 | 1 |
- Note! Before you install this product, check the kit contents. If anything is missing, please contact an Öhlins dealer.
- Warning! Before you install this product, read the Öhlins Owner’s manual. This product is an important part of the vehicle and the vehicle’s stability.
- Note! Please note that there can be small differences between your product and the images in these instructions.
- Note! Please note that during storage and transport, especially at high ambient temperatures, some of the oil and grease used for assembly may leak and stain the packaging. This will not cause damage to the product, wipe off the excessive oil or grease with a cloth.
MOUNTING INSTRUCTIONS
- Warning! We strongly recommend letting an Öhlins dealer install this product.
- Warning! If you work with a lifted vehicle, make sure that it is safely supported to prevent it from tipping over.
- Note! When you work with this product, see the vehicle service manual for vehicle-specific procedures and important data.
- Note! Before you install this product clean the vehicle.
- Put the motorcycle on a work stand so that the rear wheel barely touches the ground.
- Remove the lower attachment screws for the rear suspension.
- Remove the front shock absorber attachment screw.
- Remove the right side cover, then remove the standard hydraulic preload adjuster from the frame mount.
- Remove the standard shock absorber; if necessary remove the frame bracket under the seat, above the suspension to gain more clearance.
- Install the new shock by first pull the preload adjuster and hose thru the right side frame opening near the engine, from the seat side to the side cover side.
- Let the preload adjuster hang freely; mount the shock absorber onto the frame.
- Mount the preload adjuster bracket to the preload adjuster with loose tighten screws, and mount the bracket to the frame (use the original screw and one new one, see picture).
- Mount the side cover and check for clearance, remove and adjust the preload adjuster bracket if not in a centered position.
- Fasten the hose with supplied cable ties. Make sure that the hose runs without sharp bends and that the hose is not squeezed when the rear suspension is compressed or extended.
- Tighten all suspension shock screws with the correct torque.
- If neccessary use the extra tie raps to keep the wire harness away from the suspension shock cylinder head.
ADJUSTMENTS
Warning! Before you ride/drive, always make sure that the setup is according to the recommended setup data. Read about adjustments and setting up in the Öhlins Owner’s Manual before you make any adjustments. Contact an Öhlins dealer if you have any questions about setting up.
SETUP DATA
| Length | 320.5 | mm |
|---|---|---|
| Stroke | 43.5 | mm |
| Rebound | 16 | clicks |
| Spring preload | 19 | mm |
| Spring rate | 105 | N/mm |
| Spring free length | 170 | mm |
| Spring | 21102-36 |
Recommended free sag and ride height
R1-R2| 7| mm
R1-R3| 29| mm
F1-F2| 18| mm
F1-F3| 61| mm
Öhlins products are subject to continuous improvement and development, therefore, although these instructions include the most up-to-date information available at the time of printing, minor updates may occur. To find the latest information contact an Öhlins distributor. Please contact Öhlins if you have any questions regarding the contents of this document.
- Part no. MI_HD513_0
- Issued 2024-05-14
© Öhlins Racing AB. All rights reserved. Any reprinting or unauthorized use without the written permission of Öhlins Racing AB is prohibited.
CONTACT INFORMATION
- Öhlins Racing AB
- Box 722
- S-194 27 Upplands Väsby, Sweden
- Phone +46 8 590 025 00
- fax +46 8 590 025 80
- www.ohlins.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>