Ecosoft FU1016CABDVUP Strong Acid Cation Exchange Resin User Guide
- September 27, 2024
- ecosoft
Table of Contents
FU1016CABDVUP Strong Acid Cation Exchange Resin
“`html
Product Information
Specifications:
- Part #: FU1016CABDVUP
- Media: Strong acid cation exchange resin
- Media volume: 15 L
Product Usage Instructions
Quick Set Up Guide:
-
After installing and powering up the Ecosoft FU system, set
water hardness and current time in the Customer menu of the control
valve. -
Use the up and down buttons to change settings, the NEXT button
to save and move to the next step, CLOCK to save and exit the menu,
and REGEN to move back one step. -
To proceed, hold the NEXT and up buttons simultaneously for 3
seconds. -
Step 2I. Hardness: Set the amount of hardness
as calcium carbonate per PPM using the up or down buttons. Press
NEXT to proceed to Step 3I. -
Step 3I. Service Water Hardness (PPM): If a
mixing valve is installed, set the service hardness. The setting
range is always less than the setting in Step 2I. Press NEXT to
proceed to Step 4I. -
Step 5I. Time of Regeneration, Hour: Set the
time (hour) for regeneration using the up or down buttons. Press
NEXT to proceed to Step 6I. -
Step 6I. Time of Regeneration, Minutes: Set
the time (minutes) for regeneration using the up or down buttons.
Press NEXT to proceed to Step 7I. -
Regen: After programming the control valve,
follow these steps: -
Pour salt into the salt tank of the system to a level of 1/2 to
2/3 of the tank volume. -
Open the water supply to the softener.
-
Press the REGEN button for 5 seconds to start forced
regeneration of the system for cleaning and stratification.
FAQ
Q: How often should I perform system regeneration?
A: System regeneration should typically be done based on water
usage and hardness levels. It is recommended to set a regular
schedule for regeneration based on your specific water
conditions.
“`
MANUAL FOR PINK 150 SOFTENER
Part #
FU1016CABDVUP
Media
Strong acid cation exchange resin
Media volume 15 L
QUICK SET UP GUIDE
After installing and powering up an Ecosoft FU system, set water hardness,
current time in the Customer menu of control valve.
Use and buttons to change setting; NEXT button to save and go to next step;
CLOCK to save and exit menu; REGEN to move back one step.
To proceed, hold NEXT and buttons simultaneously for 3 seconds.
STEP 2I. Hardness: Set the amount of hardness as calcium carbonate per PPM,
using or . Press NEXT to go to Step 3I. Press REGEN to exit Installer Display
Settings.
STEP 3I. Service Water Hardness (PPM): If a mixing valve is installed in the
valve, service hardness needs to be set. Setting range is always less than the
setting in Step 2I. Press NEXT to go to Step 4I. Press REGEN to return to
previous step.
STEP 4I. Set Day Override to 1 28 days or OFF using or . Press NEXT to go to
Step 5I. Press REGEN to return to previous step.
STEP 5I. Time of Regeneration, Hour: Set the time (hour) for regeneration
using or . The default time is 2:00 a.m. This display will show on 0 if Step
4S or Step 3F is set to on 0.Press NEXT to go to Step 6I. Press REGEN to
return to previous step.
STEP 6I. Time of Regeneration, Minutes: Set the time (minutes) for
regeneration using or . The default time is 2:00 a.m. This display will not
appear if Step 4S or Step 3F is set to on 0.Press NEXT to go to Step 7I. Press
REGEN to return to previous step.
Regen
After programming the control valve:
STEP 7. our salt into the salt tank of the system to the level of 1/2 to 2/3
of the tank volume.
STEP 8. Open the water supply to the softener.
STEP 9. After that, it will start the forced regeneration of the system by
pressing the REGEN button for 5 seconds. This is necessary for cleaning the
material from impurities and for its stratification.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>