rocstor Y10G014-B1 TrueReach HDMI Splitter and Extender User Guide

rocstor Y10G014-B1 TrueReach HDMI Splitter and Extender

Important safety notice

1. Avoid placing this device near radiators, heat registers, or in direct sunlight.
2. Ensure the device is positioned in a well-ventilated area, without obstructing any ventilation openings.
3. Protect the apparatus from exposure to rain or water to prevent potential failures, fires, or electric shocks caused by liquid ingress.
4. Place the device on a stable, level surface to prevent accidental falls and malfunctions.
5. Never insert metallic objects into any open parts of the device to avoid the risk of electric shock.
6. When using a third-party power supply, verify that it meets the specified requirements to ensure proper functionality and safety.

Introduction

• This Trureach HDMI Splitter & Extender is a 1 input 2 outputs splitter extender kit designed for various applications such as outdoor advertising, studios, and multimedia classrooms.
• It efficiently distributes a single HDMI input signal to 2 identical outputs while extending these signals up to 70 meters. Supporting a resolution of 4K30Hz, it also features bi-directional IR passthrough, RS-232 control, and 3.5mm L/R audio output functions.”

Features

• Enjoy zero-latency transmission for seamless performance.
• Experience support for resolutions up to 4K@30Hz, with backward compatibility.
• Benefit from HDR10 support for enhanced visual quality.
• Easily distribute one HDMI source to two HDMI displays.
• Utilize CAT6/6A/7 network cables for signal transmission, with support for distances up to 70 meters for 1080p signals and up to 40 meters for 4K30Hz signals.
• Enable power over a network cable, requiring only the transmitter to be powered.
• Take advantage of HDMI loop-out functionality on the transmitter.
• Enjoy bi-directional IR passthrough capabilities (20~60KHz).
• Utilize RS-232 command control for enhanced device management.
• Stay protected with surge, lightning, and ESD protection features for added durability and safety.

Package Contents

Installation Requirements

5 m

Cable

| CAT6/6A/7，following standard IEEE- 568B| CAT 6/6A/7 ≤ 7 0 m
Displaydevice| TV, projector, etc . with HDMI port| HDMI cable ≤ 5 m

Panel Description – Transmitter (TX)

Connect with HDMI display device

④

⑤

| HDMI signal input

Power input

| Connect with HDMI source

Connect with D C 12 V / 1 A po wer adapter

⑥

|

Power indicator

| a. When power is on and no HDMI signal is transmitted, the indicator flashes

b. When power is on and the HDMI signal is transmitted, the indicator is always on

⑦| IR in| Connect with the IR receiver extension cable
⑧| IR out| Connect with IR blaster extension cable
⑨|

R S – 232

| Connected to a control device ( like a computer), input control commands from management

Panel Description – Receiver (RX)

⑤

|

Power indicator

| a . When power is on and no HDMI signal is transmitted, the indicator flashes

b. When the power icon and HDMI signalistransmitted , the indicatoris a lwa yson

⑥

|

Power input

| Connect with D C 5 V / 1 A power adapter

(Noneed to connect power when the transmitter is powered)

⑦| 3.5 mmL/Rout| Connect headphones or poweram plifiers to output stereo audio
⑧| HDMI signal output| Connect with HDMI display device

Installation Procedures

Connection Diagrams

Connection Instructions

1. Connect the source device to the HDMI IN port of the transmitter using an HDMI cable. Then, connect the HDMI OUT port of the receiver to the display device with another HDMI cable.
2. Use a Cat6/6A/7 cable to establish a connection between the RJ45 port of the transmitter and receiver.
3. If utilizing the HDMI loop out, connect the display device to the HDMI OUTport of the transmitter.
4. For IR passthrough, plug the IR blaster extension cable into the IR OUTport, and the IR receiver extension cable into the IR IN port.
5. If additional audio output is required, connect the speaker to the L/Rport of the receiver using a 3.5mm stereo audio cable.
6. To use the RS-232 command control, connect the RS-232 port to the control device.
7. Power up the devices by plugging in the power supply to initiate operation.

Installation Procedures

IR User Guide

1. Power

2. IR Signal

3. Null

4. Power

5. IR Signal

6. Grounding

• Plug the IR blaster extension cable into the IR OUT port of either the transmitter or receiver, and the IR receiver extension cable into the IR IN port of the same device.
• Position the emitter of the IR blaster extension cable as close as possible to the IR receiving window of the source device.
• Aim the remote control at the receiving head of the IR receiver extension cable to operate the device.

RS-232 SETTING

• Baud rate: 9600
• Data bits: 8
• Stop bits: 1
• Parity: none

ES XX On【Enter】

| 1)   ) Turn on the network signal output port( s ) , and choose from “ 01 ” to “ 02 ” ( the network ports from left to right are: 01 , 02 )

2)  )“ All” means all four ports

ES XX Of f【Enter】

| 1)   ) Turn off the network signal output port( s ), and choose from “ 01 ” to “ 02 ” ( the network ports from left to right are: 01 , 02 )

2)  )“ All” means all four ports

Reset【Enter】| Restart the device
Reco ver【Enter】| Restore device factory settings
Baud XX 【Enter】| Set the baud rate value: 9600 ( default), 19200 , 38400 , 57600 , 115200
Examples of control commands are shownbelow:
Control Command 1| ES 02 On【Enter】
Function Descriptio n| Turn on network signal output port 02

Return Values

| Received successfully| ES 02 On OK
Receive failed| ES 02 O n FAIL
Control Comm and 2| ES All Off【Enter】
Function Description| Turn off all the Network signal output ports

Return Values

| Received successfully| ES All Off OK
Receive fa iled| ES All Off FAIL
Control Comm and 3| Reset【Enter】
Function Description| Restart the device
Return Values| Received successfully| Reset OK
Receive fa iled| Reset FA IL
Control Command 4| Baud 19200【Enter】
Function Description| Set the baud rate value：19200

Return Values

| Received successfully| Baud 19200 O K
Receive fa iled| Baud 19200 FA IL

FAQ

• Q: Why there is no image output on the display device?
• A: 1) Please check the power supply and all the cables are well-connected.
  • Please check whether there is an HDMI signal input.
  • Please make sure that the corresponding network port output is not turned off by the RS-232 command.
• Q: Why is the output image unstable?
• A: 1) Please check whether the length of the network cable is within the specific range.
  • Press the “reset” button on TX or RX to restart and reconnect.
• Q: Why does the TV have a snowy/fuzzy screen?
• A: 1) Change to a better quality or shorter HDMI cable, the recommended length of HDMI cable is less than or equal to 5 meters.
  • Try another network cable and make sure that the length is within the specified range.

Technical Parameters

HDMI Perfomance

| Compatibility| HDMI 1 .4 ，HDCP 1 .4

Resolution

| 800 x 600 、1024 x 768 、1280 x 720 、1280 x 960 、

1366 x 768 、 1440 x 900 、1680 x 1050 、1920 x 1080 、

480 i@ 60 H z、 480 p@ 60 H z、576 i@ 50 H z、

576 p@ 50 H z、720 p@ 50 / 60 H z、1080 i@ 50 / 60 H z、

1080 p@ 24 / 25 / 30 / 50 / 60 H z、4 K @ 24 / 25 / 30 H z

Audio Formats| P C M 、LP C M 、DT S – H D 、DT S – A udio
Transmission distance| C AT 6 / 6 A / 7| 1080 p@ 60 H z≤ 70 m eters

4 K @ 30 H z≤ 40 m eters

IR Passback| B i- directional IR passback ( 20 – 60 k hz)
R S – 232| 3 Pin：GND – RxD – TxD ，follows R S – 232 levels Default baud rate：9600
---|---

Operating Environment

| Workingtem perature| – 20 ~ 60
Storage temperature| – 30 ~ 70
Humidity| 0 ~ 90 % R H

Protection

| ESD protection 1 a Contact discharge level 2 ( ± 4 K V ) 1 b Air discharge level 3 ( ± 8 K V )

Implem entation of the standard: IEC 61000 – 4 – 2

Lightning protection
Surge protection

Power

| Supply| TX: DC 12 V/1 ARX:DC 5V/1 A
Consum option| TX＜10 WRX＜2 .5 W

Physical Properties

| Housing| Iron
Color| Black
Weight| TX: 280 g

RX: 160 g x 2

Dimensions| TX: 151 .5 (L) x 86 .5 (W) x 19 .0 (H) m m

RX: 75 .0 (L) x 80 .0 (W) x 18 .0 (H) m m

Technical Parameters

©2024 Rocstr, Inc. Rocstor is a registered trademark of Rocstor, Inc. The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI Trade dress andthe HDMI Logos are trademarks or registered trademarks of HDMILicensing Administrator, Inc. The product name and brand name may be registered trademarks of related manufactures. ™ and ® may be omitted from the user manual. The pictures in this user manual are just for reference. We reserve the right to make changes without further notice to a product or system described herein to improve reliability, function, or design.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>