rocstor Y10E026-B1 SolidRack 6U Wall Mount Network Rack User Manual
- October 30, 2023
- rocstor
Table of Contents
Y10E026-B1 SolidRack 6U Wall Mount Network Rack
User Manual
SolidRack 6U & 8U Wall Mount
Network Rack – Low Prole – Black
User Manual
Y10E026-B1, Y10E027-B1
© 2022 Rocstor is registered trade mark of Rocstorage, Inc. Any unauthorized copying, duplicating, or other reproduction of the contents hereof is prohibited without written consent from Rocstor. All rights reserved. Other trademarks are property of their respective owners.
Introduction & Installation
Wall-Mount Bracket Installation
Warnings:
Rocstor recommends viewing your wall structure first before installing the
bracket. You may want to consult or have a professional installer to mount the
bracket to your wall structure. The bracket must be installed on a wall
structure that is able to support the mounted equipment properly. The wall
structure should be able to support at least four times the weight of the
installed mounted equipment. Make sure the wall-mount bracket is securely
installed before you mount any equipment. Failure to mount the bracket
securely, it may result in personal and/or equipment damages.
Equipment
Installation to the Wall-Mount Bracket
Included in this mounting bracket, you will find M6 Cage Nuts, Screws, and
Plastic Washers. Use these to install equipment into the Wall-Mount Bracket.
- Use the Wing (side) of an M6 Cage and insert it into the back of the Cage Nut hole.
- Use a Cage Nut Tool or hand to apply pressure to insert a 2nd Wing of the M6 Cage Nut into a designated Cage Nut Hole. Please repeat steps 1 and 2 by inserting the remainder of the Cage Nuts for your application.
- Make sure you use the Threaded Plastic Washer over the M6 Screw.
- At this time use the M6 Cage Nuts and align the Mounting Holes in the equipment and apply the Cage Nuts in step 2.
- Now please insert the assembled Screws through the Mounting Holes in the Equipment and into the M6 Cage Nuts.
- Make sure the Screws are Tightened by using a Phillips Screwdriver.
Measurements
Units Dimension (Millimeter):
Package Contents
- Wall-Mount Bracket x 1
- M6 Screws: 6U x12 – 8U x18
- M6 Cage Nuts: 6U x12 – 8U x18
- Plastic Washers: 6U x12 – 8U x18
- Expansion Bolt x 4
- User Manual x 1
Storage and Service
Five-Year Factory Warranty
Rocstor provides a Limited Factory Warranty which applies to products you have
purchased for commercial or industrial use in the ordinary course of your
business.
Terms of warranty
Rocstor warrants its SolidRack product series to be free from defects in
materials and workmanship for a period of five years from the date of
purchase. Rocstor’s obligation under this warranty coverage is limited to
repairing or replacing, at its sole discretion, any such defective products.
This warranty does not apply to equipment that has been damaged by accident,
negligence, or misapplication or has been altered or modified in any way. In
the event Rocstor repairs or provide a replacement of a defective product or
part, the warranty does not extend the original warranty period. Rocstor
reserves the right to repair or replace any parts under warranty as new or
factory re manufactured.
Non-transferable warranty
This warranty extends only to the original purchaser who must have properly
registered the product.
The product may be registered at the Rocstor Web site, https://rocstor.com
/customer-support/warranty registration.
Exclusions
If Rocstor tests or examines the alleged defect in the product and finds that
the damages or defects do not exist or were caused by a third party or an end
user’s misuse, improper installation or testing, or negligence, then Rocstor
shall not be liable under the warranty. Furthermore, unauthorized attempts to
repair or modify the product by wrong or inadequate electrical connection or
voltage, inadequate or inappropriate site operation conditions, repair,
installation corrosive area or atmosphere, a change in location or operating
conditions or use, repair by non-Rocstor designated personnel, exposure to the
elements, fire, Acts of God,
theft, or equipment installation not recommended or contrary to Rocstor’s
specifications or recommendations. Warranties will be void and Rocstor will
not be liable if the product serial number is tampered with, altered, removed,
defaced or any other cause beyond the range of intended use.
Contact Information
Corporate Headquarters
12979 Arroyo Ave
San Fernando, CA 91340 – USA
| Offce: | +1 (818) 727-7000 |
|---|---|
| Fax: | +1 (818) 875-0002 |
| Email: | info@Rocstor.com |
Technical Support / RMA
Hours: 9:00 am – 5:00 pm PST
Mon – Fri (excluding holidays)
| Tell: | +1 (818) 727-7000 (Domestic and Internationals) |
|---|---|
| Fax: | +1 (818) 875-0002 |
| Email: | support@Rocstor.com |
Sales Info
Hours: 8:00 am – 5:00 pm PST
Mon – Fri (excluding holidays)
| Tell: | +1 (818) 727-7000 (Domestic and Internationals) |
|---|---|
| Fax: | +1 (818) 875-0002 |
| Email: | support@Rocstor.com |
Corporate, Government and Academic Customers
Our Corporate Sales Team’s goal is to help our U.S.A. and Canadian customers
find a storage solution that best serves their needs. We will help you
determine your best purchasing options. For more information please contact
the appropriate department below or call us at +1 (818) 727-7000.
General sales information:
sales@Rocstor.com
Corporate sales information:
corporate_sales@Rocstor.com
Educational sales information:
academic_sales@Rocstor.com
Federal, State & Local government sales information:
government_sales@Rocstor.com
Resellers/Business Development/OEM Partners
All Channel National and International Resellers, VARs, Consultants …
contact Rocstor Channel Sales:
call: +1 (818) 727-7000
Email: reseller_info@Rocstor.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>