SEALEY AK41.V3 Caulking Gun 230mm Air Operated Instructions
- June 3, 2024
- SEALEY
Table of Contents
AK41.V3 Caulking Gun 230mm Air Operated
Instructions
AK41.V3 Caulking Gun 230mm Air Operated
CAULKING GUN 230MM AIR OPERATED
MODEL NO: AK41.V3
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
| | | ****
---|---|---|---
Refer to instruction manual| Wear eye protection| Wear Gloves| Wear ear
protection
SAFETY
WARNING! Disconnect the gun from the air supply before changing
accessories, servicing or performing any maintenance.
Maintain the gun in good condition. Replace or repair damaged parts.
Use recommended parts only. Unauthorised parts may be dangerous and will
invalidate the warranty.
Keep children and unauthorised persons away from the work area.
Avoid unintentional operation.
Ensure caulking compound manufacturer’s instructions are carefully followed.
X DO NOT hold gun or attachments close to your face (especially eyes,
ears, etc.) and do not point gun or air hose at other persons or animals.
X DO NOT carry by the air hose, or yank the hose or the gun from the air
supply.
X DO NOT use the gun for any purpose other than that for which it is
designed.
X DO NOT operate the gun if damaged.
X When not in use disconnect from the air supply and store in a safe,
dry, childproof area.
INTRODUCTION
Accepts standard 310ml cartridges. Fitted with trigger control for smooth application of caulking.
SPECIFICATION
Model no: ……………………………………………………….AK41.V3
Air Consumption…………………………………………………. 3.5cfm
Air Inlet Size:…………………………………………………….1/4″BSP
Maximum Working Pressure: ………………………. 3bar(43.5psi)
Overall Length:………………………………………………….. 300mm
Recommended Air Pressure: ………………………… 36 – 43.5psi
PREPARATION
4.1.AIR SUPPLY
4.1.1. Recommended hook-up procedure is shown in fig.2.
4.1.2. Ensure tool valve (or trigger) is in the “off” position before
connecting to the air supply.
4.1.3. You will require an air pressure stated in Section 3 and an air flow
according to specification.
ˆ WARNING! Ensure the air supply is clean and does not exceed the stated
value in Section 3 while operating the tool. Too high an air pressure and/or
unclean air will shorten the product life due to excessive wear, and may be
dangerous causing damage and/or personal injury.
4.1.4. Drain the air tank daily. Water in the air line will damage the tool.
4.1.5. Clean air inlet filter weekly.
4.1.6. Line pressure should be increased to compensate for unusually long air
hoses (over 8 meters). The minimum hose diameter should be 1/4” I.D. and
fittings must have the same inside dimensions.
4.1.7. Keep hose away from heat, oil and sharp edges. Check hose for wear, and
make certain that all connections are secure.
4.2. COUPLINGS
4.2.1. Vibration may cause failure if a quick change coupling is connected
directly to the tool. To overcome this, connect a leader hose to the tool.
4.2.2. A quick change coupling may then be used to connect the leader hose to
the air line recoil hose. See fig.2.
OPERATION
ˆ WARNING! Ensure you read, understand and apply the safety instructions
in Section 1 and follow any manufacturer’s instructions on the caulking
container.
5.1. Ensure caulking compound manufacturer’s instructions are carefully
followed.
X DO NOT hold gun or attachments close to your face (especially eyes,
ears, etc.) and DO NOT point gun or air hose at other persons or animals.
X DO NOT operate the gun if damaged.
5.2. Screw the gun cylinder A to the gun body (fig.1).
5.3. Unscrew the end cap B from the cylinder and insert the caulking
cartridge. Screw on the end cap B to retain the cartridge.
5.4. Ensure air supply is regulated as specified in Section 3 and then attach
air hose to the gun.
5.5. Aim the nozzle of the cartridge into a safe area and depress the gun
trigger to check for correct operation.
5.6. When not in use disconnect from the air supply and store in a safe, dry,
childproof area.
MAINTENANCE
6.1. Clean the gun after each use.
6.2. Check fittings and trigger components are sound and secure before each
use.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
https://qrco.de/bcy2E9
REGISTER YOUR PURCHASE HERE
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice. Please note that other versions of this product are available.
If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk
or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business
Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
© Jack Sealey Limited
Original Language Version
AK41.V3 Issue: 1 04/08/22
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>