TESLA SB-24-12-004 2024 Remove Side Apron Seals And Install Clips Instruction Manual
- September 22, 2024
- Tesla
Table of Contents
SB-24-12-004 2024 Remove Side Apron Seals And Install Clips
“`html
Product Information
Specifications
- Manufacturer: Tesla, Inc.
- Model: Cybertruck
- Model Year: 2024
- Country/Region: North America
- Build Location: Giga Texas
- Configuration: All
Product Usage Instructions
Condition:
On certain Cybertruck vehicles, the LH and/or RH side apron seal
may be visible through the frunk-to-fender gap.
Parts Required: Part Number 2067863-00-A –
BRSH-CLIP,4.9,GR2.8-3.3,P66,[B] (Quantity: 6)
Correction Steps:
-
Open the frunk.
-
Use a prytool to release the clips (x3) that attach the LH side
apron seal to the side apron assembly. Remove and discard the seal,
and repeat for the RH side apron seal. -
Install the clips (x6 total) into the LH and RH side apron
assembly holes. -
Close the frunk.
Frequently Asked Questions (FAQ)
Q: Is this procedure safe to perform without professional
training?
A: This procedure should only be performed by
trained professionals to prevent damage to surrounding
components.
Q: What if I have additional questions or need assistance?
A: For any feedback or inquiries regarding this
document, you can email ServiceBulletinFeedback@tesla.com.
“`
Tesla, Inc.
Service Bulletin
SB-24-12-004 May 29, 2024
Classification
Repair Bulletin
Model
Cybertruck
Model Year
2024
Remove Side Apron Seals And Install Clips
Section/Group
12 – Exterior Fittings
Country/Region
North America
Mobile Service
Can Perform (where permitted)
Build Location
Giga Texas
Configuration
All
The model(s) and model year(s) listed are a general approximation of the
affected VIN list. Refer to the VIN/Bulletin Tracker or Customer/Vehicle
profile to determine applicability of this bulletin for a particular vehicle.
Repair Bulletin: This repair bulletin provides instructions on addressing a
possible customer concern regarding the operation of Tesla vehicles. These
instructions should only be performed by trained professionals.
Condition
On certain Cybertruck vehicles, the LH and/or RH side apron seal may be
visible through the frunk-to-fender gap (Figure 1).
Fender
Frunk
Side apron seal
Figure 1
Correction
Upon customer complaint, remove and discard the LH and RH side apron seals,
and then plug the holes in the LH and RH side apron assemblies with clips.
Correction Description
SB-24-12-004 Not Applicable Remove And Discard LH And RH Side Apron Seals;
Install Clips Into Side Aprons
Correction
S012412004 S022412004
Time
0.00 0.06
Part Number
Description
Quantity
Parts Required 2067863-00-A
BRSH-CLIP,4.9,GR2.8-3.3,P66,[B]
6
This part number was current at the time of publication. Use the revisions listed or later, unless otherwise specified in the Parts Catalog.
Procedure
1. Open the frunk.
SB-24-12-004 _
Page 1 of 2
2. Use a prytool to release the clips (x3) that attach the LH side apron seal
to the side apron assembly (Figure 2). Remove and discard the seal, and then
repeat this step on the RH side apron seal.
CAUTION: Use care when releasing the clips so as to prevent damage to
surrounding components.
Figure 2 LH shown; RH similar
3. Install the clips (x6 total) into the LH and RH side apron assembly holes
that were previously populated by the side apron seals (Figure 3).
4. Close the frunk.
Figure 3 LH shown; RH similar
SB-24-12-004
For feedback on the accuracy of this document, email ServiceBulletinFeedback@tesla.com
Page 2 of 2
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>