BLACKWIDOW MCC-500-F Steel Motorcycle Carrier Instruction Manual
- June 3, 2024
- BLACKWIDOW
Table of Contents
MCC-500-F Steel Motorcycle Carrier
Instruction Manual
MCC-500-F Steel Motorcycle Carrier
Steel Motorcycle Carrier
Instructions for Part # MCC-500-F
GENERAL GUIDELINES
- It is the user’s responsibility to read and follow all instructions.
- Keep these instructions with the product at all times and review before each use.
- It is the responsibility of this product’s owner to furnish the instructions to any person that borrows or purchases the product.
- Inspect the product before use to ensure it is assembled properly and all parts are in safe working order and free of defects.
- Never modify this product in any way.
- All circumstances cannot be addressed in these instructions. Please use common sense and practice general safety measures when using this product.
- Parts and/or instructions are subject to change without notice.
SAFETY
- Never exceed vehicle trailer hitch tongue weight capacity or carrying capacity of your vehicle.
- Some vehicles may require air shocks of modifications to the vehicle’s suspension.
- Please check your owner’s manual for vehicle hauling capabilities and weight ratings.
- Never exceed 500 lb. max rated weight capacity of carrier
- Not recommended for tow-behind trailers, including 5th wheel and camping trailers, motor-homes or RVs.
- Not recommended for use with hitch adapters or extensions.
- Will not work with Class II or smaller receivers.
- Push the motorcycle up the carrier with a helper; never ride a motorcycle onto the carrier!
- Prior to transport, make sure the ramp of the carrier and the motorcycle are properly secured to the carrier.
- When not in use, store the carrier in a secure place out of the reach of children.
- Carrier must be level in hitch receiver and on level ground while loading and unloading
MAINTENANCE
- It is recommended that the general condition of any steel motorcycle carrier be examined each time before it is used. Keep your steel motorcycle carrier in good repair by adopting a program of conscientious repair and maintenance. Check misalignment, loose or damaged parts, and any other condition that may affect its safe operation. If any abnormal vibrations or noise occur, have the problem corrected before further use. Have necessary repairs made by qualified service personnel.
- Before each use, make sure any dirt, debris, oil, grease, etc. is cleaned off the carrier. Clean the carrier with a clean, moist cloth. Do not use solvents.
- Periodically check all hardware for tightness.
PARTS
Part| Description| Quantity| Part| Description|
Quantity
---|---|---|---|---|---
A| 1/2″x7-1/2″ (M13x190) Bolt| 4| J| R-Pin| 2
B| 3/8″x2-3/4″ (M9.5×70) Bolt| 4| K| Hitch Pin and Clip| 1
C| 3/8″x1-3/4″ (M9.5×45) Bolt| 8| L| Hitch Tube| 1
D| M10x16 Bolt| 2| M| Wheel Pin| 2
E| 1/2″ Lock Nut| 4| N| Lock Pin| 1
F| 3/8″ Lock Nut| 12| O| Ramp| 1
G| Anti-Tilt Bracket*| 1| P| Cross Bar| 2
H| Support Bracket| 2| Q| L-plate| 2
I| Platform| 2| | |
*The anti-tilt bracket includes two M10x50 bolts and two M10x40 bolts. Tools Needed: 9/16″ wrench, 11/16″ wrench, 3/4″ wrench, 17mm wrench
ASSEMBLY
Note: Bolts and nuts should be tightened by hand first; after all parts
have been assembled, go back and tighten all hardware with a wrench.
Step 1. Place the hitch tube (L) on a solid work surface with the
mounting brackets facing upward. Place the platform pieces (I) across the
hitch tube, positioned between the two middle brackets. (Make sure the ramp
brackets are facing up.) Align the holes on the platform and L-plates (Q),
secure with eight 3/8″x1-3/4″ bolts (C) and 3/8″ lock nuts (F). NOTE: The
bolts are inserted from the inside out.
Step 2. Place
the cross bars (P) on top of the platform and the support brackets (H) beneath
the platform. (The rubber-coated ends of the support brackets should be
towards the front of the carrier.) Align the holes and secure with four
3/8″x2-3/4″ bolts (B), four 3/8″ lock nuts (F) and two M10x16 bolts
(D).
Step 3. Slide the four 1/2″x7-1/2″ bolts (A) into the platform and secure
with 1/2″ lock nuts (E). Place the two wheel pins (M) in the holes at each end
of the platform and secure with R-pins (J).
Make sure all nuts and bolts on the carrier are securely tightened with
wrenches before use.
Step 4. Place the ramp (O) on the hitch tube and secure the ramp in place
using the lock pin (N).
Note: Make sure the ramp is secured in place before fully securing the
motorcycle with tie down straps. See Operation section.
MOUNTING THE CARRIER TO THE HITCH RECEIVER
- Slide the anti-tilt bracket (G) over the end of the hitch tube. The side with the three bolts should face the vehicle hitch receiver.
- With assistance, lift the empty carrier and slide the open end of the hitch tube into the hitch receiver. Secure with the hitch pin and clip (K).
- Slide the anti-tilt bracket up against the hitch receiver. Tighten the bolts against the underside of the hitch receiver collar.
OPERATION
-
Remove the lock pin (N) to unlock the ramp (O).
-
Remove the ramp and place the end rung onto the hook end of the platform (I), making sure the ramp is securely in place. The bottom end of the ramp must rest flat on a solid, level surface when loading and unloading equipment.
-
Measure the motorcycle wheelbase to make sure the wheel pins (M) are in the appropriate positions.
-
Shift the motorcycle into neutral and, with another person’s assistance, push it up the ramp. Push the motorcycle completely onto the carrier platform until the front wheel rests in place between the platform rungs.
DO NOT sit on the motorcycle while loading or attempt to drive it up the ramp. -
Lightly secure the motorcycle using tie down straps (sold separately) so that the motorcycle won’t fall over.
-
Return the ramp to the mounted position and secure with the lock pin.
-
Properly secure the motorcycle for transport, fully tightening the previously installed tie downs.
-
Attach any needed markers and/or lights to the carrier and motorcycle as required by vehicle codes.
PRODUCT WARRANTY & LIABILITY
GENERAL PRODUCT WARRANTY: Products purchased from the Authorized Dealer
(original place of purchase) or Merchant (“Dealer”) will be free of defects in
material and workmanship at the time of receipt, and will meet the
specifications stated at the place of purchase transaction or online at the
Dealer’s website, under normal use and service when correctly installed,
operated and maintained.
This product warranty is effective for the period of time stated below, unless
otherwise stated in the product instructions or depicted in the product
advertisement. All Authorized Dealer warranties are NON-TRANSFERABLE and
cover only the original end purchaser. This limited warranty does not cover
products purchased through non-authorized dealers. Non-authorized dealer
receipts are not accepted for warranty verification.
WARRANTY CLAIMS MUST BE MADE DIRECTLY TO THE ORIGINAL PLACE OF
PURCHASE.
WARRANTY PERIOD : This warranty remains in force for one year from the
date of the product’s accepted delivery. The Authorized Dealer offers a one
year manufacturer’s warranty for most products unless otherwise specified on
the product advertisement.
WARRANTY SERVICE: The Authorized Dealer will replace any defective or
malfunctioning part at no charge, including payment of the shipping costs of
parts or eplacement product to and from the manufacturer. The purchaser is
responsible for labor charges. If the product does not meet specifications as
depicted in the advertisement, the Authorized Dealer will refund the full
purchase price of the product.
Questions regarding the warranty on a specific product and warranty claims
should be directed to the Authorized Dealer with whom the purchase transaction
was made.
WARRANTY LIMITATIONS: The above warranty does not apply to products that
are repaired, modified or altered by any party other than the Authorized
Dealer; are subjected to unusual physical stress or conditions (such as
overloaded ramps or corrosion), natural disaster, governmental actions, wars,
strikes, labor disputes, riots, theft, vandalism, terrorism or any reason
beyond reasonable control; are damaged due to improper installation, misuse,
abuse, accident or negligence in use, storage, transportation or handling, or
tampering; or to products that are considered consumable items or items
requiring repair or replacement due to normal wear and tear. Product should be
inspected prior to signing for delivery. Product damage incurred during
shipping, unless noted on the Bill of Lading at the time of delivery, renders
this warranty void.
LIMITED LIABILITY: In no event shall THE AUTHORIZED DEALER be liable
to the purchaser or any third party for any indirect, incidental,
consequential, special, exemplary or punitive damages arising out f the use of
the product, including, without limitation, property damage, loss of value of
the product or any third party products that are used in or with the product,
or loss of use of the product or any third party products that are used in or
with the product.
0 81121
1-888-651-3431
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>