R G Racing FP0286 Front Wheel Sliders Installation Guide

: September 21, 2024
: R G Racing

Table of Contents

R G Racing FP0286 Front Wheel Sliders
Product Information
Product Usage Instructions
TOOLS REQUIRED
GENERAL TORQUE SETTINGS
LEGEND
ASSEMBLY DIAGRAM
FITTING INSTRUCTIONS
CONSUMER NOTICE
RETURNS POLICY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

R G Racing FP0286 Front Wheel Sliders

Product Information

Product Model: FP0286
Manufacturer: R&G Racing
Address: Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Contact: Tel: +44 (0)1420 89007, Fax: +44 (0)1420 87301, Email: info@rg-racing.com.

Product Usage Instructions

Tools Required

General Torque Settings:

M4 BOLT = 8Nm
M5 BOLT = 12Nm
M6 BOLT = 15Nm
M8 BOLT = 20Nm
M10 BOLT = 40Nm
M12 BOLT = 40Nm

Assembly Diagram

Item No.	Item	Description	Quantity
1	B0442	SPINDLE BAR	2

Fitting Instructions

Ensure all parts are present before proceeding.
Consult a dealer or a qualified technician if in doubt when fitting the product.

FAQ

Q: Can rubber washers be discarded?
A: Yes, if rubber washers are used to hold components onto bolts, they can be thrown away.
Q: Where can digital copies of the instructions be obtained?
A: Digital copies of the instructions are available at www.rg-racing.com or by contacting R&G Racing directly.

THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER THE PAGE.

SOME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.

PLEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING.
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS OR HAVE FITTED BY A QUALIFIED TECHNICIAN.

PLEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF MOUNTING TO THE BIKE.
IN THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS, THESE RUBBER WASHERS CAN BE THROWN AWAY.

DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
WWW.RG-RACING.COM.

TOOLS REQUIRED

Socket set
Rachet

GENERAL TORQUE SETTINGS

M4 BOLT = 8Nm
M5 BOLT = 12Nm
M6 BOLT = 15Nm
M8 BOLT = 20Nm
M10 BOLT = 40Nm
M12 BOLT = 40Nm

LEGEND

ITEM NO.	DESCRIPTION	QTY
ITEM 1	B0442 M8	2
ITEM 2	SPINDLE BAR	1
ITEM 3	SPACER LHS	1
ITEM 4	SPACER RHS	1
ITEM 5	M8 NYLOC NUT	2
ITEM 6	M8x19mm WASHER	2

ASSEMBLY DIAGRAM

FITTING INSTRUCTIONS

To start this fitting process, place the M8 Nyloc Nut (Item 5) onto one end of the spindle bar (Item 2) and tighten until at least a minimum of 2 threads are through the Nyloc.
A fitting suggestion: using a small amount of Super glue on one Spindle bar thread will help create an even number of threads on both sides of the swingarm protector once fully tightened.
Once the Nyloc is fitted, you can then slide the M8 washer (Item 6), one bobbin (Item 1), and RHS Spacer (Item 4) onto the bar in the configuration shown in the ASSEMBLY DIAGRAM.
Then slide the assembly through the righthand side of the front spindle. Once through place the LHS Spacer (Item 3), the other Bobbin (Item 1), M8 Washer (Item 6) onto the end of the spindle bar that’s poking through the LHS.
Then finally place the M8 Nyloc Nut (Item 5) and tighten it to the correct torque using the GENERAL TORQUE SETTINGS table.

CONSUMER NOTICE

The catalog description and any exhibition of samples are only broad indications of the Products and R&G may make design changes that do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise than under R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer’s statutory rights.

RETURNS POLICY

R &G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.

R &G Racing