R G Racing RAD0307PRO PRO Radiator Guard Installation Guide
- June 16, 2024
- R G Racing
Table of Contents
R&G Racing RAD0307PRO Radiator Guard Installation Guide
FITTING INSTRUCTIONS FOR RAD0307PRO
RADIATOR GUARD PAIR
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE.
SOME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
PLEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING.
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
PLEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF MOUNTING TO THE BIKE.
IN THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS,
THESE RUBBER WASHERS CAN BE THROWN AWAY.
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
WWW.RG-RACING.COM
TOOLS REQUIRED
- SET OF ALLEN KEYS TO INCLUDE 3mm.
- NEEDLE NOSE PLIERS.
- CABLE CUTTERS OR SCISSORS.
GENERAL TORQUE SETTINGS
M4 BOLT = 8Nm
M5 BOLT = 12Nm
M6 BOLT = 15Nm
M8 BOLT = 20Nm
M10 BOLT = 40Nm
M12 BOLT = 40Nm
LEGEND
| ITEM NO. | DESCRIPTION | QTY |
|---|---|---|
| ITEM 1 | RAD0307PRO LHS RADIATOR GUARD | 1 |
| ITEM 2 | RAD0307PRO RHS RADIATOR GUARD | 1 |
| ITEM 3 | M5x10mm BUTTON HEAD BOLT | 4 |
| ITEM 4 | M5x10MM O/D WASHER | 4 |
| ITEM 5 | CT130 RADIATOR CABLE TIE (4-PACK) | 2 |
| ITEM 6 | RUBBER BUNGS (NOT SHOWN) | 4 |
FITTING PICTURES
FITTING INSTRUCTIONS
- To begin, press the rubber bungs (item 6) provided into the holes circled in yellow in the assembly diagram, in the correct orientation.
- Slide LHS the radiator guard (item 1) into position ensuring the two mounting holes line up correctly and the guard fits neatly over the radiator, as shown in picture 2.
- Referring to the Assembly diagram on page 2, Use two M5 button head bolts (item 3) and M5 washers (item 4) to secure the radiator guard into place as shown in picture 3, do not fully tighten the bolts at this stage.
- Using two of the special radiator guard cable ties (Item 5), thread one cable tie through the upper and lower slots on the radiator guard (circled in green on the assembly diagram), ensuring the tail goes through the outer matrix hole and to the back of the radiator matrix as shown in picture 4. Note, ensure the tie does not interfere with the fans on the rear of the radiator.
- Take one of the cable tie locking pieces and carefully attach top the back of the cable tie tail and slide up until it firmly holds the radiator in place. Do not overtighten as damage to the fins can occur.
- Once secure, trim the excess cable tie from the back of the radiator using a pair of snips.
- With cable ties now in place, fully tighten the securing bolts to the recommended torque.
- Repeat the process for the RHS radiator guard (item 2).
- Check all components are secure and all bolts are tight before riding.
See more R &G products for your Motorcycle in the link below:
R&G Racing | Cleaning/Lubrication – Gleam range for All Vehicles (rg-
racing.com)
ISSUE 2 – 11/04/2023 (MH)
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer’s statutory rights.
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.
R&G Racing
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com
References
- RACING.COM - YOUR RACING CONNECTION
- Welcome to R&G | Setting the standard in bolt-on motorcycle accessories and Crash Protectors
- Welcome to R&G | Setting the standard in bolt-on motorcycle accessories and Crash Protectors
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>