micro MSD-350 Wireless Smoke Detector User Manual
- September 21, 2024
- micro
Table of Contents
- MSD-350 Wireless Smoke Detector
- Product Information
- Specifications
- Description
- Features
- Installation
- Tips for Installation
- Installation Steps
- Cleaning the Optical Chamber
- Battery Replacement
- Q: What should I do if the LED indicator does not turn on
- Q: How often should I clean the optical chamber of the smoke
MSD-350 Wireless Smoke Detector
Product Information
Specifications
- Product: Wireless Smoke Detector MSD-350 EN
- Firmware Version: 2.00
- Manufacturer: SATEL
- Compliance: Meets EN 14604 requirements
Description
The MSD-350 detector is designed to detect the early stages of
fire development when visible smoke is present. It can function as
a stand-alone device or be integrated into the MICRA wireless
system. The detector utilizes the optical method for smoke
detection and automatically compensates for changes in the optical
chamber due to dust deposition.
Features
- Fire alarm functionality
- Smoke detection using the optical method
- LED indicator for fire alarm (ON)
- Built-in sounder for fire alarm signaling (continuous sound for
5 minutes)
Installation
Tips for Installation
Before installing the MSD-350 detector, ensure you have read the
manual thoroughly to prevent errors that may lead to malfunction or
equipment damage. It is recommended to have the device installed by
qualified personnel.
Installation Steps
- Choose a suitable indoor location for installation.
- Follow the mounting guidelines provided in the manual.
- Ensure proper power supply if required.
- Test the detector after installation to confirm proper
functioning.
Maintenance
Cleaning the Optical Chamber
Regularly clean the optical chamber of the detector to ensure
optimal performance. Use a soft, dry cloth to gently wipe away any
dust or debris that may accumulate over time.
Battery Replacement
When replacing the battery of the MSD-350 detector, follow the
instructions provided in the manual. Ensure to use a compatible
battery type and dispose of the old battery properly according to
regulations.
FAQ
Q: What should I do if the LED indicator does not turn on
during a fire alarm?
A: If the LED indicator fails to illuminate during a fire alarm,
check the power supply and connections of the detector. If the
issue persists, contact customer support for further
assistance.
Q: How often should I clean the optical chamber of the smoke
detector?
A: It is recommended to clean the optical chamber of the smoke
detector at least once every six months to maintain its
effectiveness in detecting smoke particles.
Wireless smoke detector
MSD-350 EN
Firmware version 2.00
msd-350_en 08/24
SATEL sp. z o.o. · ul. Budowlanych 66 · 80-298 Gdask · POLAND tel. +48 58 320
94 00
www.satel.pl
IMPORTANT
The device should be installed by qualified personnel.
Prior to installation, please read carefully this manual in order to avoid
mistakes that can lead to malfunction or even damage to the equipment.
Changes, modifications or repairs not authorized by the manufacturer shall
void your rights under the warranty.
Description of symbols on the device: The device meets the requirements of the
applicable EU directives. The device is designed for indoor installation. The
device must not be disposed of with other municipal waste. It should be
disposed of in accordance with the existing rules for environment protection
(the device was placed on the market after 13 August 2005). The device meets
the technical regulations of the Eurasian Customs Union.
SATEL aims to continually improve the quality of its products, which may
result in changes in their technical specifications and software. The current
information on the introduced modifications is available on our website.
Please visit us at: https://support.satel.pl
Hereby, SATEL sp. z o.o. declares that the radio equipment type MSD-350 is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of
conformity
is available at the following internet address: www.satel.pl/ce
Signs in this manual Caution information on the safety of users, devices,
etc. Note suggestion or additional information.
CONTENTS
1. Features …………………………………………………………………………………………………………… 2
2. Description………………………………………………………………………………………………………… 2 Fire alarm
…………………………………………………………………………………………………………. 2 Operating mode
…………………………………………………………………………………………………. 2 Working within the wireless system
………………………………………………………………………. 3 Detector test
……………………………………………………………………………………………………… 3 Detection of dirt in the optical
chamber………………………………………………………………….. 3 Battery status control
………………………………………………………………………………………….. 3 LED indication
…………………………………………………………………………………………………… 3 Acoustic signaling
………………………………………………………………………………………………. 4
3. Installation ………………………………………………………………………………………………………… 4 3.1 Tips for
installation………………………………………………………………………………………… 4 3.2 Installation
…………………………………………………………………………………………………… 5
4. Maintenance ……………………………………………………………………………………………………… 7
5. Cleaning the optical chamber ………………………………………………………………………………. 7
6. Battery replacement……………………………………………………………………………………………. 8
7. Specifications ……………………………………………………………………………………………………. 9
2
MSD-350
SATEL
The MSD-350 detector can detect the early stages of fire development when
there is some visible smoke. It is designed to work as a stand-alone device or
within the MICRA wireless system. The detector meets the EN 14604
requirements. This manual applies to the detector with electronics version
1.2. It is supported by:
· PERFECTA alarm control panels (WRL models),
· PERFECTA-RF module,
· VERSA-MCU controller,
· MTX-300 controller,
· MICRA alarm module (firmware version 2.02 or newer).
1. Features
· Visible smoke sensor. · Detection of dirt in the optical chamber. ·
Encrypted radio transmissions in the 433 MHz frequency band. · Red LED
indicator. · Built-in sounder. · Detector test / reset button. · Battery
status control. · Tamper protection against enclosure opening (when the
detector works within the
wireless system).
2. Description
Fire alarm
Smoke detection The optical method is used for the detection of visible smoke.
When the concentration of smoke in the optical chamber exceeds a given
threshold, a fire alarm is generated. The detector automatically compensates
for gradual changes in the optical chamber caused by deposition of dust.
Fire alarm signaling The fire alarm is indicated by the LED indicator (ON) and
the built-in sounder (continuous sound) for 5 minutes.
Resetting the fire alarm Press the test / reset button (Fig. 1) to clear the
alarm. The fire alarm signaling will be turned off for 5 minutes.
Operating mode
Use the jumper to set the operating mode (Fig. 2): · jumper on (by default)
working within the MICRA wireless system (radio transmissions
and tamper protection are enabled). · jumper off stand-alone mode (radio
transmissions and tamper protection are disabled).
SATEL
MSD-350
3
Working within the wireless system
Radio transmissions Every 15 minutes, the detector sends information about its
state (periodical transmission). Additional transmissions are sent in case of:
· fire alarm, · fire alarm restore, · tamper alarm, · tamper alarm restore.
Tamper alarm Opening the enclosure (opening the tamper switch) will generate a
tamper alarm. It is indicated by the LED indicator (ON for 2 seconds).
Test mode The test mode is turned on for 20 minutes after inserting the
battery or opening the enclosure (tamper switch). When the detector is in the
test mode, the LED indicator additionally indicates periodical transmission.
Detector test If you want to test the detector operation, press the test /
reset button (Fig. 1). You will hear a short beep. A fire alarm should be
generated soon after.
Detection of dirt in the optical chamber The detector is monitoring the state
of the optical chamber. Deposition of dust in it may lead to malfunctioning of
the device. When the optical chamber requires cleaning: · LED indicator
flashes 2 times every 30 seconds, · each radio transmission contains
information about dirt in the optical chamber.
Battery status control The detector is monitoring the battery voltage. When
the battery voltage is lower than 2.75 V, i.e. the battery is low: · every 30
seconds LED indicator flashes 3 times and the sounder produces 3 beeps, · each
radio transmission contains information about low battery.
LED indication The LED indicator (Fig. 1 ) indicates: · fire alarm ON for 5
minutes,
4
MSD-350
SATEL
· dirt in the optical chamber 2 flashes every 30 seconds, · low battery 3 flashes every 30 seconds. When the detector works within the MICRA wireless system, the LED indicator also indicates: · tamper alarm ON for 2 seconds, · periodical transmission single flash (only in the test mode).
Acoustic signaling
Built-in sounder indicates: · fire alarm continuous beep sound for 5
minutes, · low battery 3 beeps every 30 seconds, · start of the detector
test single beep.
3. Installation
3.1 Tips for installation
· The detector should be installed indoors, in spaces with normal air
humidity.
· Do not install the detector outdoors.
· The detector should be installed on the ceiling, as close as possible to the
center of the room.
· Do not install the detector in places with high concentration of dust and/or
formation and condensation of water steam.
· Do not install the detector near heaters, cookers, fans or air-conditioner
outlets.
· Do not install the detector in places where there is no unobstructed
movement of air (e.g. in recesses, niches, etc.).
· If the detector is to work within the wireless system, when selecting the
place of installation, take into consideration the range of radio
communication (so that radio transmissions from the detector can reach the
receiver).
· Thick walls, metal partitions, etc. reduce the range of the radio signal. ·
It is not advisable to install the detector in close vicinity of electrical
systems, because it
can adversely affect the range of radio signal.
· If you are using a double-sided mounting tape, remember to press it
properly.
SATEL
MSD-350
5
Explanations for figures A and B: living room. bedroom. hall, lobby, etc.
kitchen. basement. primary location for detector installation. additional
location for detector installation.
3.2 Installation
The detector enclosure cannot be closed without the battery inserted.
There is a danger of battery explosion when using a different battery than
recommended by the manufacturer, or handling the battery improperly.
Do not crush the battery, cut it or expose it to high temperatures (throw it
into the fire, put it in the oven, etc.).
Do not expose the battery to very low pressure due to the risk of battery
explosion or leakage of flammable liquid or gas.
Be particularly careful during installation and replacement of the battery.
The manufacturer is not liable for the consequences of incorrect installation
of the battery. 1. Remove the plastic dust cup. 2. Turn the cover counter-
clockwise (Fig. 3) and remove it (Fig. 4).
6
MSD-350
SATEL
3. If the detector is to work as a stand-alone device, remove the jumper
(Fig. 2) and skip the steps 5-7.
Remove the jumper before installing the battery. After the battery is
installed, removing / placing the jumper has no effect on the detector
operation.
4. Install the battery. 5. Register the detector in the wireless system (see
the manual for PERFECTA control
panels / VERSA control panels / MTX-300 controller / VERSA-MCU controller /
MICRA module). 6. Place the detector where you are planning to install it. 7.
Close and open the tamper switch. If the transmission from the detector is
received, continue with the installation. If the transmission from the
detector is not received, select a different mounting location and repeat the
test. It may be sufficient to shift the device ten or twenty centimeters. 8.
If the detector is to be mounted on the ceiling using a double-sided mounting
tape (Fig. 5): – stick the tape to the enclosure base and keep pressing for
several seconds. – stick the enclosure base to the ceiling and keep pressing
for several seconds.
The surfaces to be joined using a double-sided tape must be clean and dry.
They must be free from dust and grease.
9. If the detector is to be mounted on the ceiling with screws (Fig. 6): –
place the enclosure base against the ceiling and mark the location of the
mounting holes. – drill the holes in the ceiling for wall plugs (anchors). The
wall plugs provided with the detector are intended for concrete or brick. For
other types of surface (drywall, styrofoam), use other appropriately selected
wall plugs.
– secure the enclosure base to the ceiling with screws.
SATEL
MSD-350
7
10. Replace the detector cover and lock it with a screw. The screw is
provided in the bag together with the wall plugs and screws for mounting.
11. Press the test / reset button (Fig. 1). A fire alarm should be generated
soon after. 12. Press again the test / reset button to clear the alarm.
If any work that may cause dirt to build up in the optical chamber is being
carried out on the site, put a plastic dust cover on the detector. Remove it
after the work is finished.
4. Maintenance
The detector should be subject to regular checks to ensure it is working
correctly. The periodic checks should be carried out at least every 6 months.
To check whether the detector is working correctly, press the test / reset
button (Fig. 1). A fire alarm should be generated.
5. Cleaning the optical chamber
It is recommended to clean the optical chamber at least once a year. Cleaning
the chamber is necessary when the LED indicator indicates dirt in the chamber
(2 flashes every 30 seconds). 1. Remove the cover locking screw and open the
detector enclosure (Fig. 3 and 4). 2. Remove the battery. 3. Unplug the
sounder from its socket on the electronics board (Fig. 7). 4. Pull the release
lever (Fig. 8) to unlock the electronics module and turn it
counter-clockwise (Fig. 9). 5. Remove the electronics module with the optical
chamber (Fig. 10). 6. Release the mounting catch (Fig. 11) and remove the
optical chamber cover (Fig. 12). 7. Using a soft brush or compressed air,
clean the labyrinth in the cover, as well as the base
of the optical chamber, paying attention to the recesses where LEDs are
installed. 8. Replace the optical chamber cover. 9. Lay the sounder wires in
the appropriate grooves. 10. Secure the electronics module with the optical
chamber in the cover and turn it clockwise. 11. Plug the sounder into its
socket on the electronics board (Fig. 7). 12. Install the battery.
8
MSD-350
13. Replace the detector cover and lock it with a screw. 14. Press the test / reset button (Fig. 1). A fire alarm should be generated soon after. 15. Press again the test / reset button to clear the alarm.
SATEL
6. Battery replacement
The used batteries must not be discarded, but should be disposed of in
accordance with the existing rules for environment protection. When the
detector indicates low battery (3 flashes and 3 beeps every 30 seconds),
replace the battery. 1. Remove the cover locking screw and open the detector
enclosure (Fig. 3 and 4). 2. Remove the low battery.
SATEL
MSD-350
9
3. Install a new CR123A 3 V lithium battery. 4. Replace the detector cover and lock it with a screw. 5. Press the test / reset button (Fig. 1). A fire alarm should be generated soon after. 6. Press again the test / reset button to clear the alarm.
7. Specifications
Operating frequency band …………………………………………………………….. 433.05 ÷ 434.79 MHz Radio
communication range (in open area) …………………………………………………… up to 200 m Battery
……………………………………………………………………………………………………. CR123A 3 V Battery life
expectancy……………………………………………………………………………… up to 3 years Standby current
consumption ……………………………………………………………………………….85 µA Maximum current
consumption…………………………………………………………………………..120 mA Operating temperature
range………………………………………………………………………. 0°C…+55°C Maximum humidity
……………………………………………………………………………………………. 93±3% Dimensions
…………………………………………………………………………………………… ø108 x 54 mm
Weight………………………………………………………………………………………………………………. 170 g
10
MSD-350
SATEL
The MSD-350 wireless smoke detector conforms to the essential requirements of
the EU Regulations and Directives:
CPR 305/2011 Regulation of the European Parliament and of the Council of 9
March 2011 laying down harmonized conditions for the marketing of construction
products and repealing the Council Directive 89/106/EEC on construction
products;
EMC 2014/30/EU Electromagnetic Compatibility Directive;
RED Directive 2014/53/EU of the European Parliament and of the Council of 16
April 2014 on the harmonization of the laws of the Member States relating to
the making available on the market of radio equipment and repealing Directive
1999/5/EC.
The CNBOP-PIB Certification Body in Józefów issued the Certificate of
Constancy of Performance 1438-CPR-0623 for the construction product MSD-350
Wireless Smoke Detector, confirming its compliance with the requirements of EN
14604:2006.
The CNBOP-PIB Certification Body in Józefów has tested the MSD-350 Wireless
Smoke Detector confirming its compliance with the EN 14604 Standard, within
the scope of Appendix L (approved for the use in caravans and camper vans).
The Certificate and the Declaration of Performance can be downloaded from the
www.satel.pl website.
18
SATEL Sp. z o.o. · ul. Budowlanych 66 · 80-298 Gdask · POLAND 1438
1438-CPR-0623
MSD-350 EN 14604 Fire safety. MSD-350 wireless, stand-alone smoke detector,
capable of interacting via radio with an intrusion and hold-up alarm system,
operating based on the light scattering principle, for use in buildings.
Declaration of Performance 1438-CPR-0623 Application fire safety. Technical
specifications see this manual.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>