DAKOTA MICRO DMOV-DWH7C 1080P HD Digital 7 Wireless Waterproof Monitor and 120 Degree Camera User Manual

: June 1, 2024
: DAKOTA MICRO

Table of Contents

DAKOTA MICRO DMOV-DWH7C 1080P HD Digital 7 Wireless Waterproof Monitor
Product Information
Product Usage Instructions
Included Components
Optional Wireless Kit Components
Standard Features
Power
Event Trigger Wire Operations
Monitor Operation
Specifications
Warnings
Product Warranty/Repair Process
Consumer Limited Warranty
Disclaimer
Read User Manual Online (PDF format)
Download This Manual (PDF format)

DAKOTA MICRO DMOV-DWH7C 1080P HD Digital 7 Wireless Waterproof Monitor

and 120 Degree Camera

DAKOTA-MICRO-DMOV-DWH7C-1080P-HD-Digital-7-Wireless-Waterproof-Monitor-
and-120-Degree-Camera-Product

Product Information

Specifications

Model: DMOV-DWH7C
Part Number(s): DMOV-DWH7C
Power Input: 12V
Power Source: Cigarette lighter adapter / Hardwire power plug
Event Trigger Wire Input: 10.5V – 16.9V

Product Usage Instructions

Power Connection

For Monitor:

Attach the power input connector on the monitor to the included 12V cigarette lighter power adapter.
Plug the cigarette lighter adapter into a 12V power source.

For Camera:

Attach the power input connector on the camera to the included hardwire power plug.
Attach t-tap power clips as follows:
Hardwire power adapters include two sets of wiretap and female disconnects for both power (red) and ground (blue).
The wiretap clamps onto the wire you’re connecting to; the female disconnect crimps onto the hardwire power adapter: RED for power, BLUE for ground.
The female disconnect slides firmly into the end of the wiretap, making a secure connection.
WARNING: Hardwire MUST be attached to a MAX 7.5A fused circuit or damage will occur. Warranty void if instructions are not followed.

Event Trigger Wire Operations

Event Trigger Wire Color Guide:

Event Trigger Wires Explained:

Monitor Operation

Power
Left (Volume -/Menu)
Right (Volume +/Menu)
Menu/Esc
Down (CH switch)
Up (CH switch)
OK/Camera Toggle

Frequently Asked Questions (FAQ)

Q: What should I do if the monitor does not turn on?
A: Check the power connection and ensure that the correct voltage is being supplied to the monitor.
Q: How do I change the camera view using event trigger wires?
A: Attach the event trigger wires to a 12V positive event to switch between camera views automatically.

OverView® 1080P HD Digital 7” Wireless Waterproof Monitor and 120° Camera.

Description(s)
This OverView® kit includes one (1) HD digital 7″ wireless waterproof monitor, one (1) HD digital 120° wireless cameras, and accessories.

Included Components

$DAKOTA-MICRO-DMOV-DWH7C-1080P-HD-Digital-7-Wireless-Waterproof-Monitor- and-120-Degree-Camera-Fig- $1$$

Optional Wireless Kit Components

$DAKOTA-MICRO-DMOV-DWH7C-1080P-HD-Digital-7-Wireless-Waterproof-Monitor- and-120-Degree-Camera-Fig- $2$$

Standard Features

Camera

Minimum focal distance of 5”
Built-in, high-quality CCD camera with high-performance infrared (IR) illuminator modules
IR has an effective range of 45’+ in complete darkness
Built-in CDS light-source sensor automatically turns the IRs on/off by detecting the light intensity of the environment
2.8mm Camera lens provides 110-degree field of view

Monitor

7” LED Backlit Monitor
Capable of displaying 4 digital wireless cameras
Capable of auto scan between Cameras 1, 2, 3, & 4
View cameras one at a time, side by side, or quad view
Manual image-switching modes

Power

Supplying power to your OverView® wireless monitor with provided 12v power adapter

Attach the power input connector on the monitor to your included 12v cigarette lighter power adapter.
Plug cigarette lighter adapter into 12v power source.

Supplying power to your OverView® wireless cameras with provided hardwire power adapter

Attach the power input connector on the camera to your included hardwire power plug.
Attach t-tap power clips as follows: $DAKOTA-MICRO-DMOV-DWH7C-1080P-HD-Digital-7-Wireless-Waterproof-Monitor-and-120-Degree-Camera-Fig- $3$$
WARNING: Hardwire MUST be attached to a MAX 7.5A fused circuit or damage will occur. Warranty void if instructions are not followed.

Supplying power to your OverView® wireless kit via AC power

If you would like to provide power to your OverView® wireless kit via AC power, you will need to purchase the accessory AC power adapters from your local Dakota Micro, Inc. Dealer, part number: DM-PA3.
IMPORTANT: Each unit will need an AC power adapter.

Event Trigger Wire Operations

Event Trigger Wire Color Guide

Camera 1 – Brown
Camera 2 – Yellow
Camera 3 – White
Camera 4 – Blue

Event Trigger Wires Explained

Event trigger wires can be attached to any 12v positive event. This will cause the monitor to change to that camera, regardless of the state of the monitor (i.e. ON/OFF or channel selection). The most recent event will be the primary display. So, if two (2) video channels (AV1 & AV2) are attached to an event output, the event that happens last will change the monitor to its respective camera view.
The wires can be attached to any positive output 10.5v to 16.9v switch or supply to cause the monitor to automatically switch the unit to its respective channel camera. Example: If you were to attach the AV1 wire to a positive output from an unloading auger on a combine, the monitor would switch from channel 2 to channel 1 when the auger is extended. The event circuit should be neutral in its normal state and change to HIGH (+12v) when the event is considered to be active.

Monitor Operation

Power
Left (Volume -/Menu)
Right (Volume +/Menu)
Menu/Esc
Down (CH switch)
Up (CH switch)
OK/Camera Toggle

Setting Up/Pairing Your Camera

Plug the monitor into a chosen power source. With no cameras connected, the monitor will display a “No Signal” message.
Have the monitor show one camera image at a time IMPORTANT: The camera will not pair in split screen or SCAN mode.
Plug 1 camera into the chosen power source.
Press the “MENU” button to enable menu selection. IMPORTANT: Menu NOT accessible in split screen mode.
Use the Left/Right arrows to select the “Pair” icon (pictured below)
Press the “OK” (7 on the image above) button to select.
Once selected, your monitor will display the message “Please press pair key on Tx side 20”, which means your monitor will scan for available camera signals.

To Pair Additional Cameras

Change the monitor to another video input and follow the above instructions for each additional camera.

DISCLAIMER:
If the camera signal cannot be found, unplug the camera for 10 seconds and try again.

Additional Menu Options

$DAKOTA-MICRO-DMOV-DWH7C-1080P-HD-Digital-7-Wireless-Waterproof-Monitor- and-120-Degree-Camera-Fig- $5$$ $DAKOTA-MICRO-DMOV-DWH7C- 1080P-HD-Digital-7-Wireless-Waterproof-Monitor-and-120-Degree-Camera-Fig- $6$$ $DAKOTA-MICRO-DMOV-DWH7C-1080P-HD-Digital-7-Wireless-Waterproof- Monitor-and-120-Degree-Camera-Fig- $7$$

Specifications

Camera

LCD Monitor

Warnings

When selecting a camera system from Dakota Micro, Inc., be sure to utilize the appropriate system for your use. AgCam®, EnduraCam® and InnoPro® cameras are designed for high impact, moisture, vibration, and a variety of other rough conditions. OverView® and RazerCam™ cameras and kit components are designed for light use, low vibration, and low moisture. OverView® and RazerCam™ equipment is not warranted when used in situations outside of the above-mentioned parameters. We always request that customers keep in mind that our less expensive OverView® and RazerCam™ product line is cheaper because it does not feature the reliability and durability of our AgCam® and EnduraCam® lines. The warranty available on these products reflects that durability.
To avoid electrical shock and maintain optimal functionality, do not open the enclosures. High voltage may be present and there are no user serviceable parts inside. All warranties will be void should any enclosures be tampered with in any way.
Do not use any harsh chemical solvents, cleaning agents or corrosive detergent to clean away dirt on the surface of the screen or lens.
On AgCam® and EnduraCam® products, the photo-chromic camera lenses have been made impact-resistant and have been drop-ball tested according to Sec. 3.84,21 CRF BUT ARE NOT UNBREAKABLE. Because they have been hardened chemically, they show no stress pattern. Inspect your lenses frequently. Chipped or scratched surfaces will reduce protection. Such lenses should be replaced only by the manufacturer.
Power to cameras is not interrupted by turning off the monitor; the 12v power source must be terminated when not in use to avoid battery drain. To avoid this problem be sure when hard-wiring a unit, use a fused circuit.
Do not use your Dakota Micro, Inc. camera system for anything other than legal surveillance and observation uses. Dakota Micro, Inc. is not liable for any illegal or nefarious usage.

Product Warranty/Repair Process

For Technical Support call 1 701-538-4403 OR email techsupport@dakotamicro.com.
The technician will assist in troubleshooting product malfunction.
If product malfunction cannot be remedied and a repair is deemed necessary, the Technician will issue a case number.
IMPORTANT NOTE:
The Technician will note if the repair APPEARS to be a warranty or non- warranty issue based on the customer’s description of the issues at hand. No final determination can be made until inspection and testing of the equipment is completed at the factory.
To ensure fast and effective repairs, the customer is required to send:
- Dakota Micro, Inc. product that the technician has requested/deemed necessary in the proper diagnosis and repair of malfunction. This may include some or all components of the kit.
- Original/Copy of purchase receipt.
- For serialized items ONLY, if a copy of the original purchase receipt cannot be provided, then Dakota Micro, Inc. will use the product manufacture date.
- Customer information, including return address, phone number & email address.
- Case Number provided by Dakota Micro, Inc. technical support
- Shipping and associated costs to ship product to the Dakota Micro, Inc. factory are to be borne by the customer unless otherwise specified.
Customers should mail products to:
Dakota Micro, Inc. Case # XXXX 8659 148 ½ Ave. SE Cayuga, ND 58013
Upon receipt and evaluation of the product at the Dakota Micro, Inc. factory, it will be established if the repair is warranty or non-warranty. The customer will be notified of any applicable charges.
If the repairs are deemed non-warranty and require a service/repair fee of any kind, a credit card number will be required.
If the customer is unable to be contacted over 3 weeks regarding required non-warranty repairs, the product will be held for 30 days and, if no response from the customer, the product will be discarded.
Any product returned without proper documentation may be returned at the customer’s expense.
Products returned with unconfirmed problems may be assessed an evaluation fee of up to $60 per unit.
Return shipping costs will be borne by the party at fault; in other words, if Dakota Micro, Inc. determines that the defective product was covered under warranty, Dakota Micro, Inc. pays the shipping charges. If Dakota Micro, Inc. determines that it was the customer’s fault, the customer will pay shipping charges. If a particular circumstance cannot be determined then the cost of shipping charges will be decided on a discretionary basis depending on the situation at hand.

Consumer Limited Warranty

Subject to the disclaimer, limitations and other directions stated hereafter, Dakota Micro, Inc. warrants that the Product will be free from defects in material and workmanship for periods as stated hereafter from the date of original purchase. THIS WARRANTY IS EXPRESSLY MADE INSTEAD OF ANY AND ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS. THE EXCLUSIVE REMEDY OF THE BUYER IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT. EXCEPT AS STATED IN THIS WARRANTY, DAKOTA MICRO, INC. SHALL NOT BE LIABLE FOR ANY LOSS, INCONVENIENCE, OR DAMAGE, INCLUDING DIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, RESULTING FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER RESULTING FROM BREACH OF WARRANTY, NEGLIGENCE, STRICT LIABILITY OF ANY OTHER LEGAL THEORY. Any oral statements or representations made by anyone which are contrary to or at variance with the terms stated in this LIMITED WARRANTY are void.
Dakota Micro, Inc. will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labour for the period of five (5) years for AgCam® /EnduraCam® cameras; three (3) years for InnoPro® cameras; two (2) years for AgCam®/ EnduraCam® monitors, and Wireless components; Twelve (12) Months for all Overview® and RazerCam™ Cameras & Monitors, cables and all other accessories.

In addition to the five (5) years for AgCam® /EnduraCam® cameras Dakota Micro will warranty for the life of the camera against any variety of ingress within the camera housing. This includes moisture and dust particles that are found inside the camera resulting from a manufacturing defect and does not include ingress because of damage caused by no fault of Dakota Micro, Inc. The Dakota Micro, Inc. limited warranty periods outlined above apply throughout the United States and Canada only. A one (1) year maximum limited warranty for all Products applies to all other geographic locations unless otherwise stated in writing by Dakota Micro, Inc. This limited warranty does not apply to any issues connected with appearance that have no relation to the performance of the Product nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or modified in design or construction. To enforce the rights under this limited warranty, the purchaser should follow the process outlined in the Product Warranty/Repair Process, and provide proof of purchase to Dakota Micro, Inc.

Neither the sales personnel of Dakota Micro, Inc. nor any dealer or any other person is authorized to make any warranties other than those described herein or to extend the duration of any warranties beyond the periods described herein. The warranties described herein shall be the sole and exclusive warranties and remedies provided by Dakota Micro, Inc. Correction of defects, in the manner and for the period described herein, shall constitute complete fulfilment of all liabilities and responsibilities of Dakota Micro, Inc. to the purchaser concerning the Product, and shall constitute satisfaction of all claims. In no event shall Dakota Micro, Inc. be liable or in any way responsible for any damages or defects in the Product that were caused by repairs or attempted repairs performed by anyone other than Dakota Micro, Inc.

Some states do not allow the limitation or exclusion of incidental or consequential damages, so said limitation may not apply to you. Any action at law, suit in equity, or other judicial proceeding for the enforcement of any right provided for herein or otherwise, or concerning any claim that a purchaser may have against Dakota Micro, Inc. shall be instituted only in the Courts of the State of North Dakota, either in the state district court located in Wahpeton, North Dakota or in Federal District Court located in Fargo, North Dakota. Without regard to conflicts of law principles, the laws of the state of North Dakota shall govern the interpretation and enforcement of the terms of this Limited Warranty and all aspects of the relationship between Dakota Micro, Inc., and the purchaser.
This warranty gives you specific legal rights and you may also have other rights, which may vary from state to state.

Disclaimer

Dakota Micro Inc. products, specifications, pricing, and programs are subject to change without prior notice. Dakota Micro Inc. reserves the right to make design changes at any time without obligation to retroactively install them on previously sold units.