LAMAX PartyGo1 Play Portable Speaker Instruction Manual

LAMAX PartyGo1 Play Portable Speaker

Specifications

• Overall performance
• Frequency range
• Battery
• Playback time
• Supports microSD cards up to 64 GB

Product Usage Instructions

Controls

• POWER: To turn the speaker on/off, hold down the POWER button.
• CHARGE STATUS LED: Indicates battery charge status.
• PAIRING/TWS: Press to pair devices, hold for TWS mode on/off.
• VOL -: Press for volume down, hold for previous track.
• PLAY: Press for playback/pause, answer/end call, reject call (on hold), disconnect paired device (hold for 3s), reset (hold for 8s).
• VOL +: Press for volume up, hold for next track.
• LED/BASS+: Press to switch light modes, press for BASS+ mode on/off.

Switch On/Off
To turn on the speaker, hold down the POWER button. The LED will light up, and an audible signal will sound. Hold the same button to turn the speaker off.

Pairing

1. Turn on the speaker by holding dow

LAMAX PartyGo1 Play Portable Speaker

n the POWER button. The LED will flash blue for pairing.

2. Activate Bluetooth on your device and select “LAMAX PartyGo1 Play” from available devices.
3. If pairing issues occur, reset the speaker by holding the PLAYbutton for 8 seconds.
4. To unpair speakers, press the TWS button on the main speaker.

Switch Music Sources
Press the POWER button to switch between Bluetooth, microSD card, and AUX sources. Connecting a microSD card or audio cable automatically switches modes.

FAQ

1. Q: How do I know when the battery needs recharging?
   A: The speaker will indicate when the battery needs recharging. It is recommended to recharge the battery promptly once low.

2. Q: What do I do if pairing fails?
   A: If pairing fails, try resetting the speaker by holding the PLAY button for 8 seconds and then repeat the pairing process as  described in the manual.

3. Q: Can I control songs directly on the speaker when using an audio input?
   A: When playing via the audio input, you cannot control songs directly on the speaker. Control song playback from your connected device.

Controls

LED signalling for pairing

• Flashing blue – speaker is ready for pairing
• Glows blue – speaker is paired
• Flashes blue-white – speaker is ready for TWS pairing

Switch on / off:
To turn on the speaker, hold down the POWER button. The LED will light up and an audible signal will sound. Hold the same button to turn the speaker off.

Pairing

1.  Turn on the speaker by holding down the POWER button. The LED will flash blue and the speaker is ready to pair.
2. Activate the Bluetooth connection on your phone or other device. Select „LAMAX PartyGo1 Play“ from the list of available devices. When pairing is successful, the speaker will beep and the LED will turn blue.
   If there are problems with pairing, reset the speaker by holding the PLAY button for 8 seconds. Then proceed as described in section 1. in the Pairing chapter.

TWS
To pair two speakers with each other, turn on both speakers and make sure they are not paired with a multimedia device. Press the TWS button on one of the speakers you select as the main speaker, an audio signal will sound and the LED will turn white, while the LED on the other speaker will be off. If the pairing is successful, the LED will flash for 3 seconds. Then pair the main speaker with the multime-dia device according to step 1 in the Pairing chapter. The main spea-ker will function as the left channel. Only through this main speaker can you control the functions for calls.
To unpair the speakers, press the TWS button on the main speaker.

FM Radio
After turning on the speaker, press the POWER button. Once you switch modes, you will enter the FM mode. While in FM mode, press the PLAY button to initiate „Automatic Channel Search“ – the white LED on the POWER button will blink. During the search, press the PLAY button again to end the channel search. Upon completion of the search, the first found channel will automatically play.

Switch music sources
Press the POWER button to switch between Bluetooth, microSD card and AUX sources. By connecting a microSD card or the included 3.5mm audio cable, the speaker automatically switches to the appro-priate mode. When playing via the audio input, you cannot control the songs directly on the speaker.

Charging

• 4 LEDs lit – battery is charged between 75% and 100%
• 3 LEDs lit – battery is charged between 50% and 75%
• 2 LEDs lit – battery is charged between 25% and 50%
• 1 LED blinking – battery is between 0% and 25% charged, need to recharge the battery soon

The speaker can be charged using the included USB cable from a suitable USB device – adapter, PC, power bank. Do not charge the speaker with higher input voltage and current than 5V/2A, the spea-ker may be damaged.

Parameters

The current version of the manual can be downloaded here: lamax.cz/partygo1play/manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>