ANKER A1722 Portable Power Station Instruction Manual

: September 19, 2024
: Anker

Table of Contents

ANKER A1722 Portable Power Station
Product Usage Instructions
IMPORTANT SAFETY INSTRUCTIONS
Storage and Maintenance Instructions
FAQ
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ANKER A1722 Portable Power Station

Specifications

Product Name : Anker SOLIX C300 Portable Power Station
Product Number : A1722
Model Number : 5100500XXXX V01
Weight : Net Weight (not specified in the manual)

Product Usage Instructions

Storage and Maintenance Instructions

Store the product in a cool and dry place, avoiding hot or humid environments.
If not used for extended periods, change and discharge the product once every three months to prevent malfunction.

Handling Instructions
Follow the below recommendations to ensure safe handling of the product:

Do not expose the product to high temperatures.
Avoid dropping or mishandling the product to prevent damage.

Operating Instructions

Follow these steps to operate the Anker SOLIX C300 Portable Power Station:

Ensure the product is fully charged before use.
Connect your devices to the appropriate output ports on the power station.
Turn on the power station using the designated power button.
Monitor the battery level indicator to know when to recharge the power station.

IMPORTANT SAFETY INSTRUCTIONS

Symbol: Description

Caution
Indicates a low-risk hazard. Failure to avoid this hazard could result in minor or moderate injury.
Warning
Indicates a hazard with a moderate level of risk. Failure to avoid this hazard could result in death or serious injury.
Danger
Indicates a highly risky hazard. Failure to avoid this hazard could result in death or serious injury.
Refer to operating instructions
Indicates that users should refer to operating or installation instructions before proceeding.
Risk of electric shock
Indicates components that present risk of electrical shock.
Caution, hot surface
Indicates that equipment surfaces may be hot and pose a burn risk.
PE conductor terminal

INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS

SAVE THESE INSTRUCTIONS

Warning – When using this product, basic precautions should always be followed, including the following:

Read all the instructions before using the product.
To reduce the risk of injury, close supervision is necessary when the product is used near children.
Do not put fingers or hands into the product.
Do not expose the product to rain or snow.
Use of an attachment not recommended or sold by power pack manufacturer may result in a risk of fire, electric shock, or injury to persons.
To reduce risk of damage to the electric plug and cord, pull the plug rather than the cord when disconnecting the power pack.
Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
Do not operate the power pack with a damaged cord or plug, or a damaged output cable.
When charging the internal battery, work in a well ventilated area and do not restrict ventilation in any way. Do not use the product in excess of its output rating. Overload outputs above rating may result in a risk of fire or injury.
When charging a device, the product may feel warm. This is a normal operating condition and should not be cause of concern.
Do not disassemble the product. take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire, electric shock and injury to persons.
To reduce the risk of electric shock, unplug the power pack from the outlet before attempting any instructed service.
• Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.
Attach output cables to a battery and chassis as indicated below. Never allow the output clamps to touch one another.
- Instructions shall include step by step directions for the proper use of the booster function detailing the correct steps to connect and disconnect the booster cables to the battery.
- Each step shall be a different numbered item.

CAUTION : Risk of explosion if the battery is replaced by an incorrect type.

Do not expose a power pack to fire or excessive temperature. Exposure to fire or temperature above 130℃ may cause explosion.
In normal conditions, the battery performance will decline over several years.
In case of fire, only a dry powder fire extinguisher is suitable for the product.
Do not clean the product with harmful chemicals or detergents.
Misuse, dropping or excessive force may cause product damage.
When disposing of secondary cells or batteries, keep cells or batteries of different electrochemical systems separate from each other.
Disposal of a battery into a fire or hot oven, or mechanically crushing or cutting off a battery, can result in an explosion.
Leaving a battery in an extremely high-temperature environment or low air pressure can result in an explosion or leakage of flammable liquid or gas.
Unplug the AC power cable to disconnect from the line voltage.

WARNING: GROUNDING INSTRUCTIONS

This product must be grounded. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electrical current to reduce the risk of electric shock. This product is equipped with a cord with an equipment grounding conductor and a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Improper connection of the equipment grounding conductor may result in an electric shock. Check with a qualified electrician if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product. If it does not fit the outlet, have a proper outlet installed by a qualified electrician.
Under Inverter mode, to reduce the risk of electric shock connect only one electrical equipment to the socket outlet.
The mains plug/appliance coupler is used as disconnect device, the disconnect device shall remain readily operable.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
Please refer the information on exterior bottom enclosure for electrical and safety information before installing or operating the apparatus.
If the external flexible cord of this inverter is damaged, it shall be replaced by a special cord or assembly available from the manufacturer or its service agent.
Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
Do not open or mutilate batteries. Released electrolytes are harmful to the skin and eyes. It may be toxic.
A battery can present a risk of electric shock and burns by high short-circuit current.
Failed batteries can reach temperatures that exceed the burn thresholds for touchable surfaces.
The mains socket outlet that supplies the UPS shall be installed near the UPS and shall be easily accessible.
The length of the output cords externally connected to the AC output port of the device cannot exceed 10m.
The product is Category C1 UPS and it is not intended to be used in an industrial environment.

The following precautions should be observed when working on batteries:

disconnect the charging source prior to connecting or disconnecting battery terminals;
do not wear any metal objects including watches and rings;
do not lay tools or metal parts on top of batteries;
use tools with insulated handles;
wear rubber gloves and boots;
determine if battery is either intentionally or inadvertently grounded. Contact with any part of a grounded battery can result in electric shock and burns by high short-circuit current. The risk of such hazards can be reduced if grounds are removed during installation and maintenance by a skilled person.

Storage and Maintenance Instructions

Store product in a cool and dry place, Do not store the product in hot or humid environment.
If the product is not used for long periods of time, you should change and discharge once every three months.
Keep the product on a flat surface when using, charging, and storing.
Store the product between 32°F-104°F (0°C-40°C).
Do not use or store the power station in direct sunlight for a long period, such as in a car, cargo bed, or any other place where it will be exposed to high temperatures. Doing so may cause the product to malfunction, deteriorate, or generate heat.

Handling

Operating Altitude 2000m
Pollution PD2
Power Distribution System TN,TT
AC Output Short-Circuit Current 100Apeak / 13.7Arms
DC Input Wiring VW-1,200°C, 600V, 14AWG
DC Output Wiring VW-1,200°C, 600V, 14AWG
AC Output Wiring VW-1,200°C, 600V,18AWG
PE Wiring VW-1,200°C, 600V, 14AWG
Overvoltage Category II
Enclosure IP20
Storage Temperature Range 0°C – 40°C
Charge Temperature Range 0°C – 40°C
Discharge Temperature Range -20°C – 40°C
Battery Type LiFePO4
Battery Structure Formulation 6S3P
Battery Capacity 15000mAh / 288Wh
Battery Nominal Voltage 19.2VDC
Size 16.416.124.0 cm / 6.56.39.5 in
Net Weight 4.13kg

FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

Warning : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.

Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator & your body.

The following importer is the responsible party.

Company Name: Fantasia Trading LLC
Address: 5350 Ontario Mills Pkwy, Suite 100, Ontario, CA 91764
Telephone: +1-800-988-7973

IC Statement:
This device contains licence exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

IC RF exposure statement:
This equipment complies with IC Radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 10cm between the product and your body.

This Class B digital apparatus complies with Canadian ICES-003.

Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, HongKong

Scan for online support

Scan to download the Anker app.

support@anker.com
support.mea@anker.com (For Middle East and Africa Only)
ced-cn@anker.com

US/CA) +1 (800) 988 7973
(UK) +44 (0) 1604 936 200
(DE) +49 (0) 69 9579 7960 +49 (800) 000 2522 (Anker SOLIX)
(Middle East & Africa) +971 529 750 842
(UAE) +971 8000 320 817
(KSA) +966 8008 500 030
(Kuwait) +965 2206 9086
(Egypt) +20 8000 000 826
(AU) +61 3 8331 4800
(TR) +90 (850) 460 1414
(RU) +8 (800) 511 8623
(India) +91 1800 3138831
(中国) +86 400 0550 036
(日本) 03 4455 7823
(한국) +82 02-1661-9246

FAQ

Q: What should I do if the power station gets wet?
A: In case of exposure to moisture, immediately disconnect any connected devices and dry the power station thoroughly before use to avoid damage.

Q: Can I charge the power station while using it to power other devices?
A: Yes, you can charge the power station while simultaneously using it to power other devices. However, it may affect the charging time and performance of both the power station and connected devices.