BRESSER 7009974 Thermo Hygro Sensor Instruction Manual

: September 17, 2024
: BRESSER

Table of Contents

BRESSER 7009974 Thermo Hygro Sensor
Product Information
Product Usage Instructions
FAQ
GENERAL WARNINGS
SCOPE OF DELIVERY
BEFORE YOU BEGIN
EC DECLARATION OF CONFORMITY
WARRANTY & SERVICE
OVERVIEW
WIRELESS THERMO-HYGRO SENSOR
RESET THE SENSOR
SPECIFICATIONS
Documents / Resources

BRESSER 7009974 Thermo Hygro Sensor

Product Information

Specifications

Dimensions (W x H x D): 61 x 113 x 39.5mm (2.4 x 4.4 x 1.6 in)
Weight: 144g (with batteries)
Main power: 2 x AA size 1.5V batteries (Lithium battery recommended for low-temperature environments)
Weather data: Temperature and humidity

Product Usage Instructions

Wireless Thermo-Hygro Sensor Setup

Remove the battery door.
Slide the [ CHANNEL ] switch to choose a channel.
Insert 2 x AA size batteries into the battery compartment following the polarity mark.
Close the battery door.

Note

Assign different channels to different sensors if pairing multiple sensors.
To change the channel, remove batteries or reset the unit.
Avoid direct sunlight, rain, or snow exposure.

Pairing Wireless Sensors with the Console

The console will automatically search and connect to your wireless sensor(s). Once paired successfully, sensor(s) signal strength and weather information will display on the console.

Resetting the Sensor

In case of malfunction, press the [ RESET ] button to reset the sensor.

Placing the Sensor

Choose a location outside the home shielded from direct sunlight or wet conditions for accurate readings.
Mount on a wall or place on a flat surface within approximately 150 meters transmission range.
Minimize obstructions like doors, walls, and furniture.

Important Notes

Read and keep instructions for reference.
Avoid covering ventilation holes with items like newspapers or curtains.
Do not clean with abrasive or corrosive materials.
Specifications and manual contents are subject to change without notice.

FAQ

Q: What type of batteries should I use with the sensor?

A: The sensor requires 2 x AA size 1.5V batteries. It is recommended to use Lithium batteries for low-temperature environments.

Q: How do I change the channel of the sensor?

A: To change the channel, you need to remove the batteries or reset the unit by pressing the [ RESET ] button.

ABOUT THIS INSTRUCTION MANUAL

These operating instructions are to be considered a component of the device. Please read the safety instructions and the operating instructions carefully before use.
Keep these instructions for renewed use at a later date. When the device is sold or given to someone else, the instruction manual must be provided to the new owner/user of the product.

GENERAL WARNINGS

Risk of electric shock — This device contains electronic components that operate via a power source (batteries). Children should only use the device under adult supervision. Only use the de-vice as described in the manual; otherwise, you run the risk of an electric shock.
Choking hazard — Children should only use the device under adult supervision. Keep packaging material, like plastic bags and rubber bands, out of the reach of children, as these materials pose a choking hazard.
Risk of chemical burn — Keep batteries out of the reach of children! Make sure you insert the batteries correctly. Leaking battery acid can lead to chemical burns. Avoid contact with battery acid with skin, eyes, and mucous membranes.
In the event of contact, rinse the affected region immediately with plenty of water and seek medical attention.
Risk of fire/explosion — Do not expose the device to high temperatures. Use only the recommended batteries. Do not short-circuit the device or batteries, or throw them into a fire.
Excessive heat or improper handling could trigger a short circuit, a fire, or an explosion.
Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can send the device in to be repaired, if necessary.
Use only the recommended batteries. Always replace weak or empty batteries with a new, complete set of batteries at full capacity. Do not use batteries from different brands or with different capacities.
The batteries should be removed from the unit if it has not been used for a long time.

SCOPE OF DELIVERY

Sensor, Operating instructions.

BEFORE YOU BEGIN

We recommend using alkaline batteries. If tem-peratures regularly fall below 0°C (32°F), we recommend using lithium batteries.
Avoid using rechargeable batteries. (Recharge-able batteries cannot maintain correct power requirements.)
Insert batteries before first use, matching the polarity in the battery compartment. 2x AA Bat-teries are required.

EC DECLARATION OF CONFORMITY

Hereby, Bresser GmbH declares that the equipment type with part number: 7009974 is in compliance with Directive: 2014/53/ EU.
The full text of the EU Declaration of Conformity is available at the following internet address: www.bresser.de/download/7009974/CE/7009974_CE.pd

NOTES ON CLEANING

Remove the batteries before cleaning.
Only use a dry cloth to clean the exterior of the device. To avoid damaging the electronics, do not use any cleaning fluid.
Protect the device from dust and moisture.

WARRANTY & SERVICE

The regular guarantee period is 2 years and begins on the day of purchase. You can consult the full guarantee terms and details of our services at www.bresser.de/warranty_terms.
Would you like detailed instructions for this product in a particular language?
Then visit our website via the link below (QR code) for available versions. Alternatively, you can also send an email to manu-als@bresser.de or leave a message at +49 (0) 28 72 – 80 74-220*.
Please always state your name, precise address, a valid phone number and email address, as well as the article number and name.
Number charged at local rates in Germany (the amount you will be charged per phone call will depend on the tariff of your phone provider); calls from abroad will involve higher costs.
www.bresser.de/warranty_terms

OVERVIEW

Transmission status LED
Wall mounting holder
[ CHANNEL ], slide switch to assign the sensor to channels 1, 2, 3, 4, 5, 6 or 7
[ RESET ] key
Battery compartment

WIRELESS THERMO-HYGRO SENSOR

Remove the battery door.
Slide the [ CHANNEL ] slide switch to choose a channel.
Insert 2 x AA size batteries into the battery compartment according to the polarity mark on the battery compartment.
Close the battery door.

Note:

Ensure to assign different channels of different sensors, in case you need to pair more than one sensor.
Once the channel is assigned to a Wireless Thermo-Hygro sensor, you can only change it by removing the batteries or resetting the unit.
Avoid placing the sensor in direct sunlight, rain, or snow.

PAIRING THE WIRELESS SENSORS WITH THE CONSOLE

The console will automatically search and connect to your wireless sensor(s). Once your sensor (s) pair up successfully, the sensor(s) signal strength indication and weather information will appear on your console display.

RESET THE SENSOR

In case of malfunction, press the [ RESET ] button to reset the sensor.

HOW TO PLACE THE SENSOR

Choose a location on the exterior of the home that can shield the sensor from direct sunlight or wet conditions for an accurate reading.
Hang it with the wall mount hole or place it directly on a flat surface, and make sure the transmission is within 150 meters approx.
Minimize obstructions such as doors, walls, furniture, etc.

IMPORTANT NOTE

Read and keep these instructions.
Do not cover the ventilation holes with any items such as newspapers, curtains, etc.
Do not clean the unit with abrasive or corrosive materials.
Technical specifications and user manual contents for this product are subject to change without notice.

SPECIFICATIONS

Dimensions (W x H x D)	61 x 113 x 39.5mm (2.4 x 4.4 x 1.6 in)
Weight	144g (with batteries)
**** Main power	2 x AA size 1.5V batteries (Lithium battery recommended for

DISPOSAL

Dispose of the packaging materials properly, according to their type, such as paper or cardboard. Contact your local waste-disposal service or environmental authority for information on the proper disposal.
Do not dispose of electronic devices in the household garbage! As per the Directive 2002/96/EC of the European Parliament on waste electrical and electronic equipment and its adaptation into German law, used electronic devices must be collected separately and recycled in an environmentally friendly manner.
In accordance with the regulations concerning batteries and rechargeable batteries, disposing of them in normal household waste is explicitly forbidden.
Please make sure to dispose of your used batteries as required by law — at a local collection point or in the retail market. Disposal of domestic waste violates the Battery Directive.
Batteries that contain toxins are marked with a sign and a chemical symbol.

battery contains cadmium
battery contains mercury
battery contains lead

MANUAL DOWNLOAD:www.bresser.de/download/7009974
SERVICE AND WARRANTY: www.bresser.de/warranty_terms
Errors and technical changes are reserved.
BRESSER GmbH
Gutenbergstr. 2 · DE-46414 Rhede · Germany
www.bresser.de
service@bresser.de
Bresser UK Ltd.
Suite 3G, Eden House, Enterprise Way,
Edenbridge, Kent TN8 6Hf, Great Britain

Documents / Resources

| BRESSER 7009974 Thermo Hygro Sensor [pdf] Instruction Manual
7009974 Thermo Hygro Sensor, 7009974, Thermo Hygro Sensor, Hygro Sensor, Sensor
---|---