deli T510 Digital Safe User Manual

Table of Contents

Fix the safe in a place that is not easy to move.
Drill holes for expansion bolts (or clamping screws) in the right place.
Turn the expansion bolts counterclockwise to separate.
Use the expansion bolts (or clamping screws) to secure the case to the wall.
Make sure the case is mounted in place as required and then tighten all screws.
CAUTION: Use the expansion bolt when there is a concrete wall surface. Use the clamping screw when there is a wooden wall surface.

Please do not keep emergency keys in your safe!

Dear valued customer:

Thank you for choosing our products! You’ve taken an important step in organizing and protecting your most valued possessions.
Every series of our safes is professionally made and designed to provide safety. Please take time to read and familiarize yourself with the proper operating procedures of your new safe presented on the following pages.
Again, thank you for choosing our products!

Schematic drawing of case

Schematic drawing of control panel

CAUTION: All drawings in this manual have been prepared based on the EA.
The exterior design or component positions of other models may be different from what is indicated in the drawings, while the operation is the same.

Upon first opening, users should open the safe with the emergency key. The operation in detail refers to “opening the safe with the emergency key”.
Remove emergency lock cover, then insert the emergency key, and turn it countclockwise.
Turn the knob (master key) clockwise to open the door.
CAUTION: Finish operation, pull out the emergency key and keep it in a safe place.

Open the door.
Insert 4 X AA batteries into the battery compartment.
Under normal condition, if both of the red and the green lights are on at the same time, it means the voltage is low and you should insert new batteries.
CAUTION: Replace 4 fresh batteries by lining them up in a manner as indicated by the “+” and “-” signs.When outage for longer than thirty minutes, you should reset the user’s code.

Input your user’s code (3 to 8 digits), each pressing results in one buzzer beep, and yellow light flashes.
Press the “A” ( C / #) or “B” (E / *) button, the green light will be on.
Rotate the knob (master key) clockwise and pull outwards within 5 seconds, the door is opened.
CAUTION: The user preset code “159”. Please input the user code again if the yellow light flashes with three buzzer beeps.

CLOSING DOOR

3 continuously wrong entries will activate the warming beep for 20 seconds.
If the door has not been opened with the password, the next 3 continuously wrong entries will activate the warming beep for 5 minutes.
CAUTION: The key pad would be disabled during the beeping. You can only stop the beeps by opening the safe with emergency key and power-cut by removing the battery.

With the door open, press the reset button one, start setting code when the yellow lights goes on.
Input new code (3-8 digits), and press the “A” ( C / #) or “B” (E / *) button to confirm with 2 buzzer beeps, which indicates the acceptance and storage of the new code.
If the yellow light flashes with 3 buzzer beeps, which means the code changing is not effective, and you need to try again.

OPENING THE SAFE WITH THE EMERGENCY KEY

Upon first receipt of the safe, or either the electronic circuit malfunction or codes unknown. You could also use the emergency key to open the safe.
Remove the cover of the emergency lock.
Insert the emergency key, turn it countclockwise, then turn the knob (master key) clockwise to open the door.

Thank you for your purchase of our products.
The interests of customers who purchase our products will be protected.
For any malfunction due to product quality problems.
please contact authorized local dealers or service centers with this receipt and the warranty card.

Warranty terms:

For product failures occur under normal operating circumstances, free of charge repair and spare parts replacement service shall be provided by our company within one year commencing from date of purchase.
Customers are required to present this warranty card and the original purchase invoice to our company upon request for warranty service.
- This warranty card shall be valid only after the following form is filled out in details and affixed with official seal of the dealer.
No free of charge repair service shall be provided in the event of any of the following circumstances:
Expiration of the warranty period;
Damages caused by improper use, maintenance or storage not in accordance with the requirements of the user manual;
Failure or damage resulting from unauthorized disassembly, repair or modification;
Failure or damage caused by force majeure;
Wear parts or accessories.

This warranty card is being delivered with the product, one card for one product.
Please keep this warranty card in proper condition for free warranty service. There is no replacement if lost.
Date of Purchase:——————–Y———————— M——————– D
This copy shall be cut along the dotted line and kept by the dealer.
DELI GROUP CO., LTD.
301 Xuxiake Ave. Ninghai County
Ningbo 315600 China Made in China
info@nbdeli.com
www.deliworld.com
KEEP FOR FUTURE USE
Version: 1.0
Date: 02-2023