Motive OC-1 Al Omnicam FLeet Safety Camera Installation Guide
- September 17, 2024
- motive
Table of Contents
Al Omnicam I OC-1
Installation guide
WARNING
FAILURE TO PROPERLY AFFIX THE DEVICE TO THE VEHICLE CAN CAUSE THE DEVICE TO
DETACH AND RESULT IN SERIOUS INJURY.
SIMILARLY, BOLTS, NUTS, SCREWS, THE MOUNT, AND OTHER MECHANICAL COMPONENTS
USED TO AFFIX THE DEVICE TO THE VEHICLE CAN LOOSEN, BREAK, AND FAIL OVER TIME
WHICH CAN ALSO CAUSE THE DEVICE TO DETACH AND RESULT IN SERIOUS INJURY.
READ AND FOLLOW ALL INSTALLATION AND SAFETY INSTRUCTIONS PROVIDED IN THE GUIDE
AND SUPPORT ARTICLES. REGULARLY INSPECT THE CAMERA, BOLTS, NUTS, SCREWS, THE
MOUNT, AND MECHANICAL COMPONENTS TO ENSURE THEY ARE IN GOOD WORKING ORDER AND
REMAIN PROPERLY AFFIXED TO THE VEHICLE.
YOU ARE RESPONSIBLE FOR SECURING THE MOUNT AND CAMERA TO YOUR VEHICLE,
CHECKING THE HARDWARE PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS
FOR ADJUSTMENT, WEAR, AND DAMAGE.
IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE
NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION
PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER.
THIS EQUIPMENT DOES NOT HAVE BUILT-IN VoLTE TECHNOLOGY.
Introduction
Motive Al Omnicam is the first LTE-built side/rearview camera introduced to capture 360-degree footage of vehicles. It’s an Al-enabled hardware product that provides visibility in side-swipe and rear-collision cases.
What comes in the box?
Tools required
Introduction
Fleet Managers, Fleet Admins, and Installers can now install and onboard Al Omnicam with the Motive Fleet App without going to the Fleet Dashboard. The Fleet App supports the following workflows:
- Installing a new Al Omnicam device to an existing vehicle
- Replacing an Al Omnicam device on an existing vehicle
- Moving an Al Omnicam device from one vehicle to another
Steps: Onboarding Al Omnicam using Fleet App
- Assigning the Al Omnicam
- Testing the install location
- Permanent Installation
Assigning the Al Omnicam
- Log in to the Fleet App and tap Devices at the bottom of the screen.
- Tap Install Al Omnicam.
- Scan the QR Code on the back of the Al Omnicam or the barcode from the Al Omnicam box or Select fromlist.
- Tap Continue once the serial number is identified.
- Select the vehicle in which you are installing the Al Omnicam. Only vehicles assigned with a Vehicle Gateway can be selected. Ensure you install a vehicle gateway prior to installing the Al Omnicam if it hasn’t been done already.
- Select the side of the vehicle where you are installing the Al Omnicam. Once Selected, tap Confirm.
- Selected Al Omnicam will be assigned to the selected vehicle side. Tap Continue to proceed with testing the installation location. Al Omnicam can also be assigned through the Fleet dashboard by going to:
Admin ➔ Vehicles ➔ Edit Profile ➔ Assign Al Omnicam
Testing the Installation Location of Al Omnicam
-
Once assigned, decide the mounting location on your vehicle. The surface should be as flat as possible to ensure a robust connection. Note : If you decide to use your custom bracket to mount
to the Al Omnicam, you choose to do so at your own risk.
Motive is not responsible for any damage that occurs while using the custom brackets. Please contact the Motive Support Team if you have any questions about the Al Omnicam installation. -
Test the selected installation spot by tapping on Test the installation location.
This step can be skipped. -
Power the camera using temporary power using a 12V or 24V red wire and a 5A fuse to check the mounting location field of view and tap Next. Note : Only use the red power wire and black ground wire.
Make sure NOT to use the blue-wrapped wires for any direct connection
For a fuse panel install ensure using a fuse tap or add-a-circuit to create a fused ignition source and then ground to the chassis or any other available ground on the vehicle. Read this article before trimming any wire more than 8 inches.
5A fuse will also be needed for permanent installation. -
Wait for LED to go from blinking white to solid white before tapping Next.
-
Tap Connect to Al Omnicam.
-
Mobile device will connect to the local WI-Fl of the Al Omnicam. Tap Join.
-
The upper section displays the live camera view. Tapping the lower right corner enlarges the feed.
After testing, proceed by tapping Next. -
Hold the camera with mount assembly on your selected location with the LED facing upward to check its field of view.
-
You can adjust the Field Of View by moving the camera around.
Ensure you’re getting a clear and desired view. -
Disconnect the temporary power once the installation location is fixed and tap Next.
Permanent installation
-
Click Get started to proceed with permanent installation.
-
Attach the metal plate and tap Next. Note: Only use the provided hardware kit for installation. Use the mount plate slots for the provided M4 bolts and don’t use other slotted holes for installation. Also, ensure that you have access to all M3 screw locations on the metal base plate.
-
Route the camera cable through a metal base plate and grommet hole and tap Next.
-
Power the camera permanently using the 12 V or 24 V red wire and a 5A fuse and wait until the LED turns solid white and then tap Next. Note : Split loom tubing can be used to further protect the cable if it is exposed to outside element.
-
Select the power source.
-
Assemble the body mount and tap Next. Note:
If more than 5 meters of cable is needed to connect to vehicle power, it requires an additional wire harness (20AWG is suggested).
Motive doesn’t provide the additional length wire, fuse taps, and in-line switches. -
Ensure the LED of the camera is facing up towards the sky before tightening the screws.
-
Now, check the field of view (FOV) of your installed camera. You can untighten the side screws to rotate the camera within the mount to adjust its FOV.
-
Once securely connected, your camera may undergo a software update that is indicated with a white flashing LED. Tap Next.
-
The LED turns solid white once the camera is updated and is ready to record.
The vehicle engine should be turned on to view the LIVE stream of an Al Omnicam. Note: Remove the plastic protective film on the camera once installation is complete. -
Installation is complete and the Al Omnicam is installed on the selected vehicle side.
Tap “Install another Al Omnicam in this vehicle” to install the Al Omnicam on another side of the vehicle.
Note
If you need to know the IMEI of your product, follow the steps below:
- Login to your Motive fleet dashboard
- Go to Admin ➔ Vehicles
- Select Vehicle ➔ Edit profile
- Scroll to Omnicam section If no Omnicam IMEI is found, first assign an Omnicam to the vehicle profile to show the associated IMEI info.
Safety 8 privacy
The Motive Al Omnicam is a Driver and Fleet Management aid only.
It is not a substitute for safe, conscientious driving and cannot compensate
for distracted, inattentive, or impaired driving. All warning and alert
features provided by Motive products are for informational purposes only. No
warning or alert feature provided by Motive products is intended to replace
your responsibility to observe all road and driving conditions, abide by all
traffic regulations, and use safe driving judgment at all times.
Video recordings made by Motive AI Omnicam are for personal or internal use
only.
The Motive Al Omnicam uses artificial intelligence to identify animate and
inanimate objects in video and images, potentially including individual
persons, and the data captured by the Al Omnicam may be used in the creation
and production of other Motive products and services.
In some jurisdictions, it could be considered an invasion of privacy rights to
take or publicly display photographs or videos of people or their vehicles
using this product or to publish or reproduce such photographs or videos.
Further, some jurisdictions may have laws governing the collection, use,
storage, and destruction of a person’s biometric information, including face
geometry and voiceprint.
It is your responsibility to know and comply with applicable laws and rights
to privacy in your jurisdiction, including obtaining proper consent and
authorizations.
Note
The product was validated using the suite of reliability tests that were
guided by the standards below:
- IS0-16750-3
- IS0-16750-4
- ISO 16750-5
- IEC 60529
- IEC 60068-2-5
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
- Reorient or relocate the equipment.
- Increase the separation between the equipment and receiver.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment and RSS 102 RF exposure compliance requirements. This
equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body. This Transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter.
Changes or modifications not expressly approved by Motive could void the
user’s authority to operate this equipment.
This device contains license-exempt transmitters/receivers that comply with
Part 15 of the FCC Rules and with Innovation, Science, and Economic
Development Canada’s license-exempt RSS(s). Operation is subject to the
following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Troubleshooting
855-434-3564 (US)
support@gomotive.com
helpcenter.gomotive.com
Resources
can this code or visit gomotive.com/omnicam-install for detailed information and recommendations on installing and assigning your Al Omnicam.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>