EAE UD106 Universal Dimmer Actuator Instructions
- September 18, 2024
- EAE
Table of Contents
EAE UD106 Universal Dimmer Actuator
Device Description
EAE KNX Universal Dimmer Actuator has dimming functions which can be used by phase dimming only. The device can be operated manually via push button over enclosure. Each channel can be programmed via ETS5. UD 106 has 6 independent channels and 3 channel grouping features. Channel features of dimming actuator;
- Staircase lighting
- Forced Operation
- Channel Grouping (merging outputs for high power lamps)
- Scene Function
- Electrical Measurements (Voltage)
- Error Detection (Load Error, Short-Circuit, Over-current, Over-voltage, Under-voltage, Over-heating)
All features can be used individually or together.
Technical Data
| Protection Type | IP 20 | EN 60 529 |
|---|---|---|
| Safety class | II | EN 61 140 |
| KNX Power supply | Voltage | 21V… 30V DC, SELV |
| Current consumption | < 10 mA | |
| Mains Supply | Min…Max | 185… 300V AC |
| Screw terminals | 0,5…3,31 mm² solid and stranded wire 0,5…3,31 mm² stranded |
wire with ferrule 0.5 Nm
Connections| Max. tightening torque KNX| 0.5 Nm Bus connection terminal
Switching & Dimming| 6 outputs,
Trailing and Leading-Edge Dimming
Cable length| Max. 200 meters
Max. switching power| 300 VA per channel
300 W halogen, incandescent lamps per channel 300 W Inductive transformers per
channel
Output| | 250 W Phase-cut dimmable LED lamps per channel 120 W constant
voltage drivers Multiplying the output power by parallel connection of
channels.
Min switching power| 9 W
Mechanical Life| Lifetime
Type of contact| Electronically controlled
Installation| 35mm mounting rail| EN 60 715
Operating elements| LED (red) and button On/Off Button| For physical address
programming For Switching/Dimming lights
Temperature range| Ambient| -5° C + 45° C
Storage| -25° C + 55° C
Humidity| Max. air humidity| 85 % no moisture condensation
Dimensions| L x W x H Width in units (18 mm module| 66 x 180 x 90 mm 10
modules
Box| Plastic, polycarbonate, colour grey
CE| In accordance with the EMC guideline and LV directives
Electrical Installations| EN 60 669-2-1
EMC requirements| EN 63 044-5-2
Operation and Display
-Programming Led (3)
Red led lights up after the programming button is pressed.
-Status Leds
Blinks when error occurred, Stays when switched ON.
Connection Example
Scale Drawings
Commissioning
Determination of the physical address and setting of parameters are actualized
with Engineering Tool Software (ETS5 or higher). “.knxprod” file must be
imported to the ETS. Please check website for latest “.knxprod” file.
www.eaetechnology.com
A detailed information about parameter
configuration can be found in Product Manual of device.
Installation and commissioning of device
may only be implemented by trained electricians. The relevant standards,
directives, regulations and instructions must be observed when planning and
implementing the electrical installation.
- When connecting the device make sure that the device is isolated!
- Protect the device against moisture, dirt and damage during transport, storage and operation!
- Do not operate the device out of the specified technical data which is stated.
- The device may only be operated in closed enclosures (Distribution boards etc.)
Cleaning
If device becomes dirty, only a dry cloth can be used for cleaning. It is not suitable to use wet cloths, caustics and solvents.
Customer Support
© EAE Technology
Ikitelli Org. San. Bolg. Ziya Gokalp Mah. Eski Turgut Özal Cad.
No: 20, Zip Code: 34490 Başakşehir/Istanbul Tel: +90 212 549 97 13
www.eaetechnology.com
References
- EAE Technology – KNX Akıllı Ev Sistemi, Aydınlatma Otomasyonu
- EAE Technology – KNX Akıllı Ev Sistemi, Aydınlatma Otomasyonu
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>