habitat 2008608 Exposed Bulb 3l Floor Lamp Instruction Manual
- September 9, 2024
- habitat
Table of Contents
2008608 Exposed Bulb 3l Floor Lamp
“`html
Specifications:
- Product Name: Exposed Bulb 3L Floor Lamp
- Model Numbers: 2008608 (Black), 2911362 (Brass)
- Energy Efficiency Class: E
- Usage: Household and indoor use only
- Bulb Type: Max. 6W LED ES/E27 bulb
Product Usage Instructions:
Safety Warning:
For household and indoor use only. Please read and retain these
instructions for future reference.
Assembling:
-
Remove all protective materials and place parts on a smooth
surface. Arrange them in a line. -
Insert tubes as instructed and secure tightly.
-
Arrange wires under the plastic cover and slot them into
place. -
Cover the plastic cover on the bottom of the base and fix it
tightly with the provided screws.
Bulb Replacement:
-
Switch off mains power supply.
-
Allow the bulb to cool down for at least 10 minutes before
replacing. -
Use a cloth to cover the bulb when handling it.
-
Loosen and remove the old bulb, then replace with a new one of
the same voltage and wattage.
Maintenance:
IMPORTANT SAFETY WARNING: Lay cables properly,
clear screw holes of cables, and fit base plate flush before adding
screws.
Recycling Information:
Recycle waste electrical goods at designated facilities to help
the environment. Do not dispose of electrical products with normal
household waste.
Frequently Asked Questions (FAQ):
Q: Can I use bulbs with wattage higher than 6W?
A: No, the lamp is designed for a maximum of 6W LED ES/E27 bulbs
to ensure safety and proper functioning.
Q: How often should I check the cables for maintenance?
A: It is recommended to regularly inspect the cables to ensure
they are properly laid and not obstructing any screw holes.
“`
EXPOSED BULB 3L FLOOR LAMP
2008608 (Black) 2911362 (Brass)
Caution: This product contains three light source of energy efficiency class E
Care & Instruction Manual
For household and indoor use only. Please read and retain these instructions
for future reference.
Safety Warning
· Read these instructions carefully and familiarize yourself with the
procedure before assembling the unit.
· Take all the components and fittings out of the plastic bag and separate
them into their groups. · Ensure you have enough space to lay out all the
parts before assembly. · Always be sure to use the correct type and wattage of
bulbs as indicated on the fitting. Never · exceed the wattage stated. · To
avoid scratching it is recommended that you assemble the unit on a soft level
surface. · When changing the bulb, always switch off at the mains and allow
the old bulb to cool down before
handling. Dispose of used bulbs carefully. · This luminaire is Class II
insulated. · The luminaire is designed for INDOOR USE ONLY
Assembling
1. Remove all protective materials from the package and place all parts on a
smooth surface. Arrange them in a line.
2. Insert tube A into tube C and screw them tightly, repeat the same step for
tube B into tube D , tube C into tube F , tube D into tube G .
3. Insert tube E into tube H and screw them tightly. 4. Insert tubes F ,G ,H
into each hole on top of the base I . Put washers K ,L ,O onto the teeth
of each bottom tube, add nuts M,N ,P onto each washer, and screw them tightly.
5. Arrange the wires under the plastic cover and put them into the wire slot
as shown in picture V . 6. Cover the plastic cover J on the bottom of the base
and fix it tightly with 6 screws U as shown
in picture W. IMPORTANT SAFETY WARNING: To avoid the risk of electric shock,
follow these instructions carefully: · Lay the cables properly in the
compartments. · Check and ensure that the screw holes are clear of any cables.
· Fit the base plate flush before adding the screws. · Failure to follow these
instructions may result in serious injury. 7. Repeat steps above for the other
tubes. 8. Install the recommended bulb R ,S ,T into each lamp holder. 9. Once
the installation is complete, insert the plug into the socket. 10. If the
product fails to light up, unplug it before investigating the issue.
Bulb Replacement
1. Switch off the mains power supply. 2. Before replacing the bulb, allow it
to cool down for at least 10 minutes. 3. Never touch the bulb with your
fingers directly, cover it with a cloth. 4. Loosen the bulb and remove it from
the lamp. 5. Replace a new bulb with same voltage and wattage (Max. 6W LED
ES/E27 bulb).
· This product contains 3 light source of energy efficiency class
Maintenance
CAUTION! Always disconnect power supply when servicing or cleaning. · This
luminaire is designed for indoor use only. · Use a clean dry soft or slightly
damp cloth. · Do not use abrasive cloths or polishes as this may cause damage
to the product.
IMPORTANT SAFETY WARNING: To avoid the risk of electric shock, follow these
instructions carefully: Lay the cables properly in the compartments. Check and
ensure that the screw holes are clear of any cables. Fit the base plate flush
before adding the screws.
V W
Recycling electrical products You should now recycle your waste electrical goods and in doing so help the environment. This symbol means an electrical product should note be disposed of with normal household waste. Please ensure it is taken to a suitable facility for disposal. Visit www.recycle-more.co.uk, click on “bank locator” and enter your postcode to find your nearest recycling site.
We care about our quality and what you think, if you have any comments, good and bad, please call our Careline Habitat: 0345 640 2020 or visit Habitat. co.uk Your statutory rights are not affected.
Made in China for Habitat, Argos Limited, London, EC1N 2HT,UK. Argos (N.I.)Ltd, Forestside Shopping Centre, Upper Galwally, Belfast,BT8 6FX,UK.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>