habitat 4885795 Century Wood 2 Light Wall Light Instruction Manual

: June 6, 2024
: habitat

Table of Contents

habitat 4885795 Century Wood 2 Light Wall Light
Product Information
Product Usage Instructions
FAQs
Dimensions
Care & Instruction
Important
Instruction for use
A Guide to
Types Of Walls
Recycling electrical products
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

habitat 4885795 Century Wood 2 Light Wall Light

Product Information

Specifications:
- Product: 2L wall light
- Model Number: 4885795
- Dimensions: Width-45.0 cm, Depth-21.0 cm, Height-32.0 cm

Product Usage Instructions

Care & Instruction Manual:
- For household and indoor use only. Please read and retain these instructions for future reference.
Important Instructions for Use:
- This luminaire is designed for indoor use only and must be fitted to a DRY SURFACE as any dampness in plaster or paint can damage the finish. Do not use a polish or abrasive cleaner, just a soft dry cloth.
Bulb Replacement:
- Switch off the mains power supply.
- Before replacing the bulb, allow it to cool down for at least 10 minutes.
- Never touch the bulb with your fingers directly, cover it with a cloth.
- Loosen the bulb and remove it from the lamp.
- Replace with a new bulb of the same voltage and wattage (Max. 8W E14 LED bulb).
- Only compatible with LED bulbs.
A Guide to Wall Mounting & Fixings:
- IMPORTANT:
- When drilling into walls, always check that there are no hidden wires or pipes.
- Make sure the screws and wall plugs used are suitable for supporting your unit. Consult a qualified tradesperson if unsure.
HINTS:
- Always use a larger screw and wall plug if unsure.
- Use the recommended drill bit to match wall plug and hole size.
- Drill the hole horizontally, avoid forcing or enlarging it.
- Take extra care when drilling high walls, ceilings, and ceramic tiles.
- Ensure wall plugs are well-fitted and tight in the drilled hole.
Care & Maintenance:
- SAFETY: Always check fittings and locations for safety in and around the home. Use appropriate fittings for different wall types.
Fitting:
- Check the fitting periodically to ensure wall plugs or screws do not become loose.
Recycling electrical products:
- You should recycle your waste electrical goods to help the environment. Visit www.recycle-more.co.uk for your nearest recycling site.

FAQs

Q: Can I use this wall light outdoors?
- A: No, this luminaire is designed for indoor use only.
Q: What type of bulb should I use for replacement?
- A: Use a Max. 8W E14 LED bulb as specified in the instructions.
Q: How often should I check the wall light fitting?
- A: It is recommended to check the fitting periodically to ensure stability.

Dimensions

Width -45.0 cm
Depth -21.0cm
Height -32.0cm

Care & Instruction

For household and indoor use only
Please read and retain these instructions for future reference

Important

For your safety, this product must be installed in accordance with wiring regulations from the Institute of
Engineering and Technology (IET) and current local Building Regulations.
If in any doubt, or where required by the law, consult a competent person who is registered with an electrical self-certification scheme. Further information is available online or from your Local Authority.
To prevent electrocution, switch off at the mains supply before installing or maintaining this fitting.
Ensure other persons cannot restore the electricity, supply without your knowledge.
To avoid damage to concealed wiring during installation, establish the direction of the supply cable before drilling fixing holes.
Always be sure to use the correct type and wattage of bulbs as indicated on the fitting. Never exceed the wattage stated.
When changing the bulb, always switch off at the mains and allow the old bulb to cool down before handling. Dispose of used bulbs carefully.
This fitting is Class II appliance. It should be fitted to a lighting supply protected by a 5 amp fuse or equivalent breaker. The input supply cord must be double-insulated.
The luminaire is designed for indoor use only.
Not suitable for use with a dimmer switch.

Instruction for use

Switch off the electricity supply at the fuse board.
Remove the mounting bracket from the fitting by removing the 2 screws. (Fig. 1a)
Using the mounting bracket as a template, mark and drill fixing holes in the wall. Ensure the holes are drilled into a joist or other suitable mounting surface and not just into plaster.
Attach the mounting bracket to the wall using suitable fixings. (Fig. 1b)
The input supply cord of live (L) and neutral (N) need to be fully covered by the small sleeving (provided) and fastened by the plastic belt (provided) to make sure the small sleeving are fixed well on the cables (Fig. 2)
Ensure the electrical connections are covered with suitable insulation tape.
The weight of the fitting must be supported whilst making the electrical connections as follows: (Fig. 3)
- a. Connect supply live (normally brown or red) to fitting live (marked “L”) on the terminal block.
- b. Connect supply neutral (normally blue or black) to fitting neutral (marked “N”) on the terminal block.
- NOTE: Ensure electrical connections are tight and no loose strands of wire are left out of the terminal block.
Place the fitting onto the mounting bracket and push any excess cable into the canopy void. Secure the fitting into position using the 2 screws removed earlier. Take care not to trap or damage wiring.
Fit the lamp standard & lampshade(Fig. 4)
Fit the bulb: Type and wattage as indicated on the fitting. The wattage indicated must not be exceeded.
Switch on the electricity supply at the fuse board.

Maintenance

This luminaire is designed for indoor use only and must be fitted to a DRY SURFACE as any dampness in plaster or paint can damage the finish.
Do not use polish or abrasive cleaner just a soft dry cloth.

Bulb Replacement

Switch off the mains power supply.
Before replacing the bulb, allow it to cool down for at least 10 minutes.
Never touch the bulb with your fingers directly, cover it with a cloth.
Loosen the bulb and remove it from the lamp.
Replace a new bulb with the same voltage and wattage ( Max.8W E14 LED bulb).
Only compatible with LED bulbs.

A Guide to

Wall Mounting & Fixings

IMPORTANT: When drilling into walls always check that there are no hidden wires or pipes etc. Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualified tradesperson if you are unsure.

HINTS:

General Rule Always use a larger screw and wall plug if you are not sure.
Ensure you use the recommended drill bit to match the wall plug and hole size.
Ensure you drill the hole horizontally, do not force the drill or enlarge the hole.
Take extra care when drilling high walls, ceilings and ceramic tiles. Ensure the plug is fitting below the ceramic tile to avoid splitting or cracking.
Ensure wall plugs are well fitted and are a tight fit in the drilled hole.

Types Of Walls

You can use one of the following types of wall plug if your walls are made of brick, breeze block, concrete, stone, wood or plasterboard.

No.1 “Standard” Wall Plug General Wall Materials
- These come in various sizes and are made from plastic or sometimes wood fibre.
No.2 “General Purpose” Wall Plug Aerated / Breeze Block
- Generally, aerated blocks should not be used to support heavy loads, use a specialist fitting in this case.
- For light loads, a General Purpose Plug can be used.
No.3 “Shield Anchor” Wall Plug Heavy Loads
- For use with heavier loads such as TV & HiFi Speakers and Satellite Dishes etc.
No.4 “Cavity Fixing” Wall Plug
- For use with plasterboard partitions or hollow wooden doors.
No.5 “Cavity Fixing – Heavy Duty” Wall Plug
- For use when fitting or supporting heavy loads such as shelving, wall cabinets, and coat racks.
No.6 “Hammer Fixing” Wall Plug
- For use with walls stuck with plasterboard.
- The hammer fixing allows it to be fixed to the wall rather than the plasterboard.
- Always check the fixing is secure to the retaining wall.

CARE & MAINTENANCE

SAFETY Always check the fitting and location to ensure your safety in and around the home.
FITTING From time to time check the fitting to ensure the wall plugs or screws do not become loose.

Recycling electrical products

You should now recycle your waste electrical goods and help the environment.
This symbol means an electrical product should not be disposed of with normal household waste.
Please ensure it is taken to a suitable facility for disposal.
Visit www.recycle-more.co.uk, click “bank locator” and enter your postcode to find your nearest recycling site.
We care about our quality and what you think, If you have any comments, good and bad, Please call our Careline0345 640 2020
Or visit Habitat.co.uk Your statutory rights are not affected.
Made in China for Habitat, Argos Limited, London, EC1N 2HT, UK. Argos (N.I.) Ltd, Forestside Shopping Centre, Upper Galwally, Belfast, BT8 6FX, UK.