PATLITE GA0001165 02 BDV Voice Synthesizer Installation Guide

PATLITE GA0001165 02 BDV Voice Synthesizer

Notice to Customer

Thank you very much for purchasing our Patlite products.

• This product requires installation, wiring, and other related work. Be sure to ask an expert technician to perform these procedures.
• This installation manual is intended for the technician who performs the installation and wiring of the product.
• A separate user’s manual is provided for customers who operate the product after installation.
• Be sure to read the user’s manual before operating the product.

WARNING

• Indicates an imminently dangerous condition: failure to follow the instructions may lead to death or serious injury.
• Request the installation and wiring to be accompanied by a professional contractor. If installation is done improperly, it may result in fire, electric shock, falling, or malfunction.

CAUTION

• Indicates a potentially dangerous condition: failure to follow the instructions may lead to slight injury or property damage.
• Use a soft cloth dampened with water to clean the product. (Do not use thinner, benzine, gasoline, or oil.)

To Installers or Contractors

• Read this manual thoroughly before using this product to ensure correct use.
• If there are any questions concerning this product, refer to the contact information at the end of USER’s manual and contact your nearest PATLITE Sales Representative.

Matters to be kept without fail for Safety Purposes

WARNING

• At the wiring and mounting of products, be sure to cut off the power source. There is a risk of electrical shock.
• Do not disassemble or modify the product. There is a risk of fire, electrical shock, etc.
• For repair, check, etc of inside the product, please inquire to each sales office or technical consultation service written on the last page.
• Pay attention not to mistake wiring work. If wiring is mistaken, the internal circuit may burn out and it will become a cause of fire.
• Be sure to use the power supply within the allowable voltage range of the product. Otherwise, it may become a cause of fire and/or failure.
• For the installation with execution of work, be sure to ask a professional company. Otherwise, there is a risk of electrical shock, fire and/or falling etc.

CAUTION

• Be sure to connect the external fuse for protection of the power supply circuit and the internal circuit of the product.
• Do not use it at the place where vibration exists that exceeds the specifications. In addition, be sure to install in an upright direction at the place where vibration exists. There is a risk of damage and/or falling of the product.
• The trouble occurred due to mishandling against the warning and caution matters, and/or due to disassembling, modification, natural disaster, etc. cannot be guaranteed. Further, avoid the usage under conditions other than the contents described in this manual.

Request

• Use it in an environment where strong radio waves and/or inductive noise do not exist. Otherwise, there is a risk of noise generation from the Speaker.
• Use it in an environment where corrosive gas does not exist. Otherwise, it will become a cause of failure.
• To avoid electrostatic breakdown, start to work after discharging static electricity which is charged on a human body.
• By touching an earthed metallic part with a bare hand, static electricity can be discharged.
• Perform fitting of each part at a recommended torque value.
• Pay attention not to lose the parts such as the terminal covers, front covers etc. which are to be detached while performing work.
• If this product is used for safety-sensitive security purposes, be sure to perform daily checks, and establish the system design that can cope with the occurrence of accidental trouble and failure.

Caution on copyright
If a work that was recorded or copied from music CDs or other media is used in public places, law enforcement for copyright infringement may be imposed. When using a work that was recorded or copied from music CDs or other media, be sure to obtain permission from the author. In addition, the copyright of audio/music data that are distributed or sold by PATLITE Corporation belongs to PATLITE.
It is strictly prohibited to copy/reprint the partial or whole contents of audio/music data of PATLITE Corporation or to transfer/sell them on computer networks etc. without the permission of the right holder.

Indication Method of Models

Parts Names

How to install

Install the product according to the procedure below

1. Create mounting holes on a mounting surface (board thickness: 1mm – 10mm) where there is enough space for the mounting angle. (See the mounting dimensions diagram)
2. (a) Insert the product from the front of the mounting surface.
   • (b) Attach the mounting angle that comes with the product to the holes on the side of the product.
   • (c) Then fasten the screws of the mounting angle. (Recommended tightening torque: 0.7$0.1N • m)
3. Confirm that the product and the mounting angles are installed properly.

WARNING

• At the mounting of products, be sure to cut off the power source. There is a risk of electrical shock.
• For the installation with execution of work, be sure to ask a professional company.
• Otherwise, there is a risk of electrical shock. fire and/or falling etc.

CAUTION

• Choose a location for the mounting surface where it has enough strength to support the weight of the product, and where there is less vibration.
• In addition, do not use it as a vehicle. Failure to do so may be the cause of injury or damage to the product.
• Be sure to use both pieces of mounting angle, and fasten them with the recommended tightening torque.
• Failure to do so may be the cause of injury or damage to the product.

Request

• Secure enough space in which the mounting angle can also be installed when choosing a mounting surface.
• Install the product on a flat surface without bumps and dips.
• Failure to do so may weaken its resistance to water and dust To prevent the product from falling in places where vibration may be generated, apply locking adhesive or the like, and perform periodic checks of the tightness of the mounting angle.
• When mounting it at a high place, choose the place where a foothold exists for facilitating repair work.
• If it is used under the connected state to the power supply, then provide a switch that can easily cut off the power supply in proximity to the product, for the safety purpose.
• Please install it so as not to close the air hole.

Other Precautions

• The clamp face might resonate by the material, the thickness of the clamp face, the reproduction volume of the product, and the vibration sound generated. Measures can be taken by reinforcing the clamp face.

How to perform wiring

• Before wiring the product remove the terminal cover. And after the completion of the wiring attach the terminal cover.
• For the external contact of the signal line, use a no-voltage contact circuit such as a relay switch or open collector circuit (NPN type). As for the contact capacity, see the table below.
• The terminal screws should be fastened with the recommended tightening torque (0.3N • m).
• Wiring examples
• OBDV-15KF

BDV-15JF

• Do not supply a voltage for the signal line.
• Failure to do so may damage the product.

Chart1. Specifications of Signal line

Chart2. Contact Capacity

Chart3. Inrush current • Fuse

WARNING

• At the wiring of products, be sure to cut off the power source. There is a risk of electrical shock.
• Pay attention not to mistake wiring work. If wiring is mistaken, the internal circuit may burn out and it will become a cause of fire.

CAUTION

• Be sure to connect the external fuse for protection of the power supply circuit and the internal circuit of the product.
• The terminal screws should be fastened with the recommended tightening torque (0.3N • m). Otherwise, there is a risk of damage by short-circuit, after wiring comes off.

Request

• Before switching on the power supply, confirm that the wiring is correctly performed.
  For countermeasures of noise, it is recommended to perform wiring as short as possible and to use shielded wires. In addition, if a signal line is passing along high voltage cables or its wiring is located at the place likely to receive induction noise, there is a risk of malfunction by the effect of noise.

• If a no-voltage contact such as a relay or a switch etc. is used for the power supply line, select the contact for which rush current is considered. If capacity is insufficient, it will become a cause of welding (deposition) of the contact and/or malfunction.

• The use of M3 ring terminals with the insulating coating is recommended for the wiring of the terminal block to prevent the disconnection of wires. Recommended product: N1.25-3 (Product confirming to RoHS)

Other Precautions
• If the power supply or signal lines are switched on simultaneously at the use of plural units, a shift of playing the voice period will occur.
• BDV-15JF comes to receive the influence of the noise easily if you connect the OV terminal to the terminal COM.

How to set the product

Opening and closing the front cover
Open or close the front cover according to the procedure shown below when performing tasks such as adjusting the volume of the voice or selecting the mode switch.

1. Remove the mounting screw (M3×6) for the front cover.
2. Push the lower front cover section (Part A in the figure on the right) lightly with a finger to slide it downward.
3. When an SD card is to be used, remove the waterproof packing for the slot.
4. After completing tasks, attach the parts removed in the procedure from O to (3 in the opposite order. (Recommended tightening torque: 0.3N • m)

Other Precautions

• Attach the waterproof packing for the slot securely. Failure to do so may weaken the product’s resistance to water and dust.
• Fasten +screw for the front cover with the recommended tightening torque.
• Please do not lose detached parts.

Selecting play mode

• By operating mode switch, one of the play modes shown below can be selected.
  [factory default setting]

• The message is registered to No.4 or earlier: A

• The message is registered to No.5 or later: B

• Use a flat-blade screwdriver with a blade thickness of 1.0mm or thinner for turning the switch.

how to select the play mode

1. Change the operation mode switch to the play mode you want to use.
   When you select the mode I, J, K, L, M, N, O, and P, The play mode is test mode.

2. Reactivate the product. (It is also possible to reboot from the front side of the product with the SD card. When the SD card is inserted, the information sound is played. Afterwards, when the information sound is playing again, the mode has been changed.)

3. Confirm the message that each CH is playing, and the play mode was changed.

Play mode (Setting with operation mode switch)

A| Bit input mode| CH input: CH1 – CH4 Playback Messages: 4
B| Binary input mode| CH input: CH1-CH4 Playback Messages: 15
C| Bit Input – Sound Reduction Mode| CH input: CH1 – CH3 Playback Messages: 3 CH4: Input reduces the volume by 10dB.
D| Binary Input -Sound Reduction Mode| CH input: CH1 – CH3 Playback Messages: 7 CH4: Input reduces the volume by 10dB.
E| Bit Input – Priority Input Mode| CH Input: CH1 to CH4 Playback Messages: 4

When one of the signal wires between CH1 to CH4 is entered for a bit input and an input message is entered during message playback, the message will interrupt the message being played. Even if the input is held down. the message playback will be reproduced only once, and there is no pr or ty input order.

F| Binary Input – Priority Input Mode| CH Input: CH1 to CH4 Playback Messages: 15

When one of the signal wires between CH1 to CH4 is entered for binary input and an input message is entered during message playback, the message will interrupt

the message being played. Even if the input is held down. the message playback will be reproduced only once, and there is no priority input order.

G| Bit Input – Hold Playback Mode| CH Input: CH1 to CH4 Playback Messages: 4

When the signal wires from CH1 to CH4 for a bit input are held when short- circuited to the common wire, the message will repeat until the signal wire is removed from the common. Once the input is lost, the playback w II stops.

H| Binary Input – Hold Playback Mode| CH Input: CH1 to CH4 Playback Messages: 15

When the signal wires from CH1 to CH4 for a binary input are held when short- circuited to the common wire, the message will repeat until the signal wire is removed from the common. Once the input is lost, the playback w II stops.

l~P| Test mode| The Message No.1 plays.

Refer to “6-5. Message Playback”. About the operation of each mode.

Request

• Make sure that there is no misalignment with the operation mode switch when selecting.
• If there is misalignment as shown in the figure on the right, the play mode selected may not play.

Rewriting the Message
By using an SD card (Model: SDV-2GP Sold separately), and a pattite playlist editor, the message can be rewritten.
The maximum length of time for this product is a total of 63 seconds (in case of 64kbit/s, Fs=44.1kHz / internal memory size 508KB). For the method of creating data and storing it on an SD card, see the instruction manual for the sound writing tool.

Message rewriting procedure

1. Turn on the power of the product, Confirm neither COM nor CH are short-circuited.
   • The message rewriting cannot be done while the voice is playing or the test is playing.
2. After opening the front cover and Inserting the SD card which is rewritten the playlist and message data, the information sounds “PIPO” and Rewriting begins.
3. When the rewriting is completed and the information sounds “PI”, Remove the SD card.
   • Rewriting should be completed within 60 seconds. When playing the information sound other than the above, or when no response, the rewriting is not completed.
   • See Section “Before Requesting Repair”. Moreover, when the volume has been minimized, the information sound is not heard.

Request

• For the SD card, use type SDV-2GP sold separately. Operation is not guaranteed if an SD card of any other type is used.

• When formatting the SD card, do it in either of FAT16.

• Depending on formatting conditions, there is a possibility that the data stored in the SD card cannot be read if the format is not supported by this product. To avoid formatting issues, please make sure that your OS is compatible with FAT16 formatting, or that you use the formatting tool that is provided by the SD Association (link below). https://www.sdcard.org/downloads/formatter/index.html
  (Note: formatting tool requires administrative rights)

• When inserting the SD card into the card slot, pay attention to the orientation of the SD card. And do not forcibly insert the SD card into the card slot. Doing so may cause damage to the product and the SD card.

• Please note that the foreign body doesn’t enter the card slot.

Volume Adjustment

• The sound level can be adjusted by the volume control.
• Use a flat-head screwdriver with a blade width of 1.0mm or thinner for turning the volume control.

PLEASE

• Turn the volume control lightly, a torque over 0.3N • m can damage the volume control.

NOTE

• As the sound increases, the possibility of distortion may also occur.
• Due to environmental conditions and tolerances. the volume may not be at zero sound level.
• The volume is turned halfway at the factory before shipment.
• The images in this manual may vary in comparison to the actual product and are only for illustration.
• Specifications may change without notice due to continual product improvement.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>