PATLITE WDR-LE-Z2-PRO Wireless Data Acquisition System WD Pro Receiver Instruction Manual

June 6, 2024
PATLITE

Wireless Data Acquisition System WD PRO Receiver
TYPE
WDR-L(E)-Z2-PRO(-L) Instruction Manual

Notice to Customer

Thank you for your purchasing our PATLITE products.

  • This product requires installation and wiring work. Request the installation and wiring be performed by a professional contractor.
  • Prior to installation, read this manual thoroughly before using this product to ensure correct use.
  • Re-read this manual before conducting maintenance, inspections, repairs, and so on. If there are any questions concerning this product refer to the contact information at the end of this document and contact your nearest PATLITE Sales Representative.
  • For instructions on how to use this product, download the Instruction Manual from our website.
Home Page Address www.patlite.com

To the Contractor

  • This installation manual is written for the professional who will perform the installation and wiring.
  • Return this manual to the customer.

Before you begin

■About Safety Symbols

  • To prevent injuries to the user and other personnel, as well as to prevent damage to assets, note the following.
  • The following symbols classify warnings and cautions and describe the level of harm and damage that will occur when the corresponding instructions are ignored.

WARNING This symbol indicates, “Failure to follow the instructions may lead to death or serious injury.”

CAUTION This symbol indicates, “Failure to follow the instructions may lead to injury or property damage.”
•The following symbols classify and describe the content of associated messages.

| This symbol identifies “Prohibited” operations that should never be carried out.| ****| This symbol identifies Mandatory” instructions that should always be carried out.| | This symbol identifies “Prohibited” operations that “general “Caution” related _ information.
---|---|---|---|---|---

•Safety Precautions

WARNING
Do not use this product in the vicinity of implanted cardiac pacemakers and other medical equipment, as this product’s radio waves may affect the performance of these devices.
Do not use or install the product in locations where liquids such as water is present, oil will splatter, or locations that are humid or dusty. Failure to follow these instructions could result in fire, electric shock, or product failure.
Do not disassemble any part other than that which can be detached from the product.
To prevent accidents, do not use this product other than for its intended purpose and do not run operations or maintenance other than those described in this manual.
Do not use this product where high reliability is required and where human life is involved, such as medical equipment, atomic energy equipment and machinery, aviation and aerospace, transportation, and control of other equipment. If this product is used for these applications, we cannot be held responsible in the event of injury or property damage.
Do not modify or disassemble this product. Failure to follow these instructions could result in fire or electric shock.
Do not use this product when there is condensation. Failure to follow these instructions could result in fire or electric shock.
Do not allow liquids on the product, and do not allow it to have contact with metallic objects. Failure to follow these instructions could result in fire or electric shock.
Request the installation and wiring be performed by a professional contractor if construction work is involved. Failure to follow this instruction could result in fire, electric shock or falls.
Tum off the power before performing any electric wiring or product installation. Failure to follow this instruction could result in electric shock or fire.
In places such as aircraft and hospitals, turn off this product where usage of wireless devices is prohibited and where its radio waves affect surrounding equipment.
We cannot foresee all circumstances concerning the handling and dangers associated with this product. Therefore, not every possible danger is indicated in this instruction manual. To prevent accidents when operating or maintaining the product, in addition to the safety guidelines identified in the instructions of this manual, follow all general safety guidelines.
****In the unlikely event that there is an abnormal situation such as smoke or odors emitting from the product, immediately cut the power supplied to the product. Continued use of the product in this condition could result in fire or electric shock.

CAUTION
Do not install this product near other electrical appliances. If you install this product near a facsimile, personal computer, television, microwave oven, or equipment using a motor, this product may not operate properly.
Do not use or store this product in the following locations. Failure to follow this instruction could result in a malfunction or equipment damage.

  •  Environments with poor breathability and ventilation.
  • Near equipment that generates strong electrical or strong magnetic fields.
  • Places exposed to direct sunlight.
  • Locations are subject to shock and vibration.
  • Near heating appliances.
  • Environments where there is dust, iron powder, and so on.
  • Places near fire or environments with high temperatures and humidity
  • Locations where the product may experience a drop.
  • Locations exposed to salty sea air.
    Do not use this product near chemicals. This product could melt or become deformed if any chemicals adhere to it.
    To clean this product, wipe with a soft cloth dampened with water. (Do not wipe with cleaners containing thinners, benzine, gasoline, or oil.)
    Due to the nature of radio waves, communication can be disabled even over insignificant distances as a result of noise or other environmental factors.
    To prevent static electricity, discharge the static electrical charge in your body before starting work. (You can discharge static electricity by touching your hand on grounded metal objects.)
    ****Use only the specified replacement parts listed in this manual.

Package Contents

PATLITE WDR LE Z2 PRO Wireless Data Acquisition System WD Pro Receiver -
box

Part Names and Dimensions

PATLITE WDR LE Z2 PRO Wireless Data Acquisition System WD Pro Receiver -
part

Model Number Configuration

WDR-L-Z2-PRO(-L): WD PRO Receiver, AC adaptor included
WDR-LE-Z2-PRO(-L): WD PRO Receiver, AC adaptor not included
*(-L) option refers to software specifications.

Mounting Methods

WARNING
** Before any work is done, disconnect the power. Affix the product to the bracket before supplying power to the product.
CAUTION
**
The following requirements are necessary for the mounting location.

  • Minimal vibration
  • Sufficient strength
  • Flat

****When installing the product in a wall, install with the wiring side down to prevent dust and other intrusions.

  1. Remove the main unit screws from the product.
    Note: • Be careful not to drop the mounting screws

  2. Slide the main unit up and detach it from the I bracket.

  3. Use screws to secure the bracket to the mounting surface.
    Recommended Torque I 1.4 N • m
    Note: • Screws to affix the bracket are not included. Please provide your own. (bracket thickness: 6 mm)
    • Center with the mounting hole, and affix screws at two or more locations.
    PATLITE WDR LE Z2 PRO Wireless Data Acquisition System WD Pro Receiver -
methods

  4. Connect a USB or LAN cable and AC adaptor or power terminal to the main unit.
    (→6 Wiring Method)

  5. Line up the indented part of the main unit with the projected pad of the bracket, then slide the main unit down to attach to the bracket.

Note:

  • When attaching the main unit to the bracket, take care not to pinch the cable.

  • Confirm the left and right sides of the projected/indented parts line up.

  • Slide the main unit until it clicks.
    6. Use the main unit screws to secure the main unit to the bracket.
    Note:

  • Use the main unit screws to securely attach the main unit and bracket.

  • Do not tighten the main unit screws more than necessary. Failure to follow these instructions could result in equipment damage.

  • Be careful not to drop the mounting screws.

Wiring Method

This product does not include the USB cable, LAN cable, and lead wires. Please provide your own.
WARNING
Without power supplied to the LAN cable, AC adaptor, or lead wires, affix the product to the bracket before supplying power to the product.
**
CAUTION
**
Input power from either the power terminal or the AC adaptor. (Power input is not required when using a PoE power supply with the USB or LAN cable.)
6.1 LAN Cable Wiring Method
CAUTION
Make sure the PoE network is indoors, and that none of the LAN cables is run outdoors. Failure to follow this instruction could result in equipment damage due to transient voltage from lightning. The LAN cable should be rated for Category 5e or higher (Category 6 or higher recommended). (You can use either straight cable or cross cable.)
For the LAN cable RJ-45 connector that connects to the main unit, select one that satisfies the shape and dimensions shown in the figure to the right. When the LAN cable is connected, do not also connect a USB cable.

  1. Insert the LAN cable into the main unit’s LAN port.
    Note: Push in the LAN cable until it dicks.
    PATLITE WDR LE Z2 PRO Wireless Data Acquisition System WD Pro Receiver -
cable2

6.2 USB Cable Wiring Method
CAUTION
Use the supplied cable tie.
Use a USB cable 3 m or shorter.
When the USB connector is connected, LAN communication is not possible. Only connect the cables that will be used. O For the USB cable connector that connects to the main unit, select one that satisfies the shape and dimensions shown in the figure to the right.

  1. attach the cable fixing plate to the main unit.
    PATLITE WDR LE Z2 PRO Wireless Data Acquisition System WD Pro Receiver -
fig1

  2. Attach a cable tie to the cable fixing plate.

  3. Insert the USB cable into the main unit’s USB connector.

  4. Secure the USB cable with the cable ties.
    PATLITE WDR LE Z2 PRO Wireless Data Acquisition System WD Pro Receiver -
fig2Note: Use nippers to cut any excess from cable ties.

6.3 Power Supply Wiring Method
There are two different power supplies for this product: AC adaptor and power terminal.
6.3.1 When Using AC Adaptor Power Supply

**CAUTION
**
You can only use the supplied AC adaptor or ADP-001 (option) in the main unit’s DC jack.

  1. Insert the plug of the AC adaptor (accessory or option) into the main unit’s DCI jack.
  2. In Pass the AC adaptor cord along with the guides.’

PATLITE WDR LE Z2 PRO Wireless Data Acquisition System WD Pro Receiver -
fig3

6.3.2 When Using Power Terminal Power Supply

WARNING
Be careful you insert the lead wires in the correct slots. Failure to follow this instruction could result in short-circuit and fire. after connecting the lead wires, confirm none of the live parts are exposed. If the live parts are exposed, a short circuit between the lead wires could result in burnout or fire.
****Do not use a power supply greater than 100 W. Failure to follow this instruction could result in fire or electric shock. This product is intended to be supplied by a Listed Power Unit marked “Class 2” and rated from 24 Vdc, less than 4A.

  • Power Terminal Pin Arrangement
    PATLITE WDR LE Z2 PRO Wireless Data Acquisition System WD Pro Receiver -
fig4

  • Power Terminal Wiring Method

  1. press a flat-blade screwdriver on the operation button of the power terminal and push.

  2. Insert the stripped lead wire into the insertion slot.
    Note: Insert the lead dire straight in.

  3. Pull off the screwdriver from the operation button.
    Note: (Check if the lead wire is locked into place.)

  4. As illustrated, pass the lead wires along with the guides.

(Point )—

  • Use a flat-blade screwdriver with a blade-edge width of 3 mm or less and thickness of 0.6 mm or less. (Or equivalent)
  • Do not push the operation button harder than necessary with the screwdriver. Failure to follow this instruction could result in equipment damage.
  • Strip 6 to 7 mm of the insulation from the lead wire.
  • When removing the lead wire, do not simply pull the wire to remove it. (Make sure you first push the operation button-down with a flat-blade screwdriver to release the lock.)

Recommended lead wire specifications

Wire Type UL1007/UL1430
 Wire Gauge (Stranded Wire) Ø 0.51 to 1.29 mm (A G24 to 16)

Use wire with a temperature rating of 75 °C or higher, and copper wire conductors.

PATLITE WDR LE Z2 PRO Wireless Data Acquisition System WD Pro Receiver -
fig5

Specifications

Model WDR-L-Z2-PRO(-L) WDR-LE-Z2-PRO(-L)
Rated Voltage 24 VDC (power terminal input, DC jack input), 48 VDC (PoE), 5

VDC (USB bus power)
| AC Adaptor accessory| 100 – 240 VAC 50/60Hz| —
Operating Voltage Range| 21.6 to 26.4 VDC (power terminal input, DC jack input),
43 to 57 VDC (PoE), 4.75 to 5.25 VDC (USB bus power)
| AC Adaptor accessory| 90 – 264 VAC| —
Rated Current
Consumption| Standard| 100 mA (at 24 VDC) 70 mA (PoE: at 48 VDC) 300 mA (USB: at 5 VDC)
Maximum| 150 mA (at 24 VDC) 100 mA (PoE: at 48 VDC) 500 mA (USB: at 5 VDC)
Rated Power
Consumption| Standard| 3.0 W (AC Adaptor accessory: at 100 VAC)| —
Maximum| 4.5 W (AC Adaptor accessory: at 100 VAC)| —
Power Su l In ut
pp y p| Power terminal (screwless terminal block), DC jack for AC adaptor,
USB Type B (USB bus power compatible), LAN connector (IEEE802.3af Classe compliant)
Operating Ambient
Temperature| Main Unit| -10 °C to 50 °C
AC Adaptor accessory| 0 °C to 40 °C| —
Ambient Operating Humidity| 85% RH or less, no condensation, no freezing
Storage Ambient
Temperature| Main Unit| -20 °C to 60 °C
AC Adaptor accessory| -10 °C to 70 °C| —
Storage Ambient Humidity| 85% RH or less, no condensation, no freezing
Mounting Location / Mounting Method| Indoor / Horizontal installation Wall mounting Ceiling mounting
Protection Rating| IP20
Mass| 300 g ± 10% (except AC Adaptor accessory)
Status Lamp| Status display LED x 4
Operation button| Setting dip switch x 1, maintenance dip switch x 1, reset switch x 1
Transmitter Options| WDT-4LR-Z2, WDT-5LR-Z2, WDT-6LR-Z2, WDT-6LR-Z2-PRO,
WDT-5E-Z2, WDT-6M-Z2 (mixed-use possible)

■ For Customers in U.S.A.

•FCC notation requirement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
♦FCC CAUTION
Note: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. The equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. (Responsible party in the U.S.A.) PATLITE U.S.A. Corporation, 20130 S. Western Ave. Torrance, CA90501, U.S.A.

For Customers in Europe
•EU Declaration of Conformity,
This product conforms to EN standards and shows the CE Marking. This product has been tested and found to comply with the limits for a Class A device, pursuant to EMC DIRECTIVE. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This product must not be used in residential areas We PATLITE Corporation, 4-1-3, Kyutaromachi, Chuo-ku, Osaka-shi, Osaka 541-0056 JAPAN declare under our sole responsibility that the product described below is in compliance with the following directives. – Product Name: Wireless Data Acquisition System WD PRO Receiver
– Company Logo:
– Communication Frequency: 2405 to 2480 MHz (16 channels)
– Transmission Output: Maximum 3 mW or less (at the antenna feed point)
– Directive: Electromagnetic Compatibility Directive(EMC): 2014/30/EU
– RoHS Directive: 2011/65/EU
– Radio Equipment Directive: 2014/53/EU
– Low Voltage Directive (LVD): 2014/35/EU Visit our homepage at www.patlite.com/ce/wd_07539.html to download “EU Declaration of Conformity”.

■ WDR-LE-Z2-PRO(-L) ONLY
■ For Customers in Singapore
Complies with IMDA Standards DA106138
■ For Customers in Canada
Canada, Innovation, Science and Economic Development Canada (ISED) Notices
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Innovation, Science, and Economic Development Canada (ISED) radio frequency exposure limits. The Wireless Device should be used in such a manner that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the ISED RF Exposure limits under mobile exposure conditions. (antennas are greater than 20cm from a person’s body).
■ For Customers in Thailand,
This telecommunication equipment conforms to the technical standards or requirements of NBTC.

PATLITE Corporation XHead office ■www.patlite.com/
PATLITE (U.S.A.) Corporation ■www.patlite.com/
PATLITE Europe GmbH XGermany ■www.patlite.eu/
PATLITE (SINGAPORE) PTE LTD ■www.patlite-ap.com/
PATLITE (CHINA) Corporation ■www.patlite.cn/
PATLITE KOREA CO., LTD. ■www.patlite.co.kr/
PATLITE TAIWAN CO., LTD. ■www.patlite.tw/
PATLITE (THAILAND) CO., LTD. ■www.patlite.co.th/
PATLITE MEXICO S.A. de C.V. •www.patlite.com.mx/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals