SUNRISE MEDICAL RGK Tiga StreetJet Compatibility Handbike User Guide

RGK Tiga StreetJet Compatibility Handbike

“`html

Product Specifications

• Brand/Model: StreetJet

• Manufacturer: Sunrise Medical

• Compatibility: Check website for approved combinations

• Clamp Options:

  • Version A: One Touch Clamps for round tube frames, adjustable
    diameter 19mm – 24mm

  • Version B: One Touch Clamps for round tube frames, adjustable
    diameter 25mm – 35mm

• Straight Tube Section Requirement: At least 45mm straight
  section needed on the front frame tube

• Front Frame Width Ranges:

  • 220-275mm
  • 275-330mm
  • 330-425mm

• Footrest Height Requirement: At least 60mm from ground to
  underside of footrest

Product Usage Instructions

Step 1: Combination Agreement

Check the approved combination between StreetJet and your
wheelchair on the Sunrise Medical website.

Step 2: Front Frame Tube Diameter Check

Ensure that the StreetJet mounting clamps (A, B, C) fit the
front frame tubes of your wheelchair based on the diameter
requirements.

Step 3: Mounting Height Verification

Confirm the minimum mounting height of 322mm for 12 & 16
wheel configurations.

Step 4: Straight Tube Section Measurement

Check for a straight section of at least 45mm on the front frame
tube for proper fitting of One Touch Clamps. The clamps should be
positioned below any bends or insets.

Step 5: Front Frame Width Check

Verify that the front frame width falls within the specified
ranges: 220-275mm, 275-330mm, or 330-425mm.

Step 6: Footrest Height Measurement

Measure the distance from the ground to the underside of the
footrest, ensuring it is at least 60mm.

Frequently Asked Questions (FAQ)

Q: How do I know if my wheelchair is compatible with

StreetJet?

A: Refer to the combination overview on www.sunrisemedical.eu to
check for compatibility.

Q: What should I do if my front frame tube diameter doesn’t

match the available clamps?

A: Contact customer support for assistance in finding suitable
mounting solutions or alternative options.

Q: Can I adjust the mounting height of StreetJet?

A: The minimum mounting height requirement is crucial for proper
installation and function; altering this height may affect
performance and safety.

“`

StreetJet Compatibility Guide

Wheelchair brand / model Sunrise Medical
Nitrum Nitrum Hybrid Helium Xenon² Xenon² Hybrid Argon² Neon² Easy 200 Easy Life R Easy Life F Easy max QS5 X (FF only)

Docking
C C C C C B A A A A A B

RGK Tiga Tiga Sub4 Tiga F2 Octane Octane Sub4 Hilite Hilite XTR Maxlite
Pro Activ Traveler Speedy Buddy

Wheelchair brand / model

Rev.:12/2023
Docking
B B B B B B B A
B B B

Please note: The above list is an indication of wheelchair models the StreetJet can be mounted on. However, frame shape, CoG, wheel-size, and seat- depth are of influence. Additionally, a straight section of the frame tube of at least 45 mm is also necessary for the attachment of the clamps. Therefore, it is essential to try and test it to be 100% sure! Or ask your supplier for advice. The compatibility guide only shows wheelchairs with a signed combination agreement. Find 6-Step-Compatibility-Check on the next page.
www.SunriseMedical.eu

StreetJet 6-Step-Compatibility-Check

The StreetJet is compatible to wheelchairs with box and open frame or similar frame type with frame integrated footrests and a frame angle between 75° and 90°. To ensure the compatibility of the StreetJet to the wheelchair, please follow the compatibility check guidance below.
1 – Combination agreement – Check, if the combination between the StreetJet and your specific wheelchair is approved. The combination overview can be found on www.sunrisemedical.eu
2 – Front Frame Tube Diameter – Check if the available StreetJet mounting clamps fit to the front frame tubes of the wheelchair. The following clamp shapes are available:

A

B

C

Version A One Touch Clamps for round tube frames, adjustable diameter 19mm – 24mm (STE010053)

Version B One Touch Clamps for round tube frames, adjustable diameter 25mm – 35mm (STE010054)

Version C One Touch Clamps for oval tubes (Quickie Helium, Quickie Nitrum, Quickie Xenon² FF) (STE010059)

3 – Minimum Mounting Height Measurement – The optimal angle of the StreetJet to the ground is 80°. For optimal performance, it is recommended to not fall below 322mm minimum mounting height (measured from floor to bottom edge of the clamp).

min 322mm

12″ & 16″ wheel 322mm minimum mounting height

min 322mm min 45m

StreetJet 6-Step-Compatibility-Check
4 – Straight Tube Section Measurement – To fit the One Touch Clamps properly a straight section on the frame tube of at least 45 mm is needed. Please check if there is a straight section on the front frame tube of at least 45mm, at the minimum mounting height or above. If there is an inset, the mounting position of the clamps must be below the bend.
12″ & 16″ wheel 322mm minimum mounting height 5 – Front Frame Width Measurement – The width of the front frame measured inside tube to inside tube on the minimum mounting height or above needs to be between 220mm – 425mm. Measured width differs from the seat width due to the measuring method or frame version (inset, V indentation, ab- or adduction, etc.). Use only the measured dimension and not the seat width to check the compatibility. Please select the appropriate front frame width range on the order form!
Front Frame width ranges: 220-275 mm 275-330 mm 330-425 mm

min 322mm min 45m

StreetJet
6-Step-Compatibility-Check
6 – Footrest Height Measurement – The distance measured from the ground to the underside of the footrest needs to be at least 60mm

References

• Wheelchairs, Mobility Scooters, Rollators | Sunrise Medical

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>