SDMC NP3081GA-V2 Dual Band Wi-Fi Gpon Terminal Installation Guide
- September 5, 2024
- SDMC
Table of Contents
SDMC NP3081GA-V2 Dual Band Wi-Fi Gpon Terminal
Package Content
- NP3081GA-V2 x 1
- Optic Cable x 1
- Power Adapter x 1
- Ethernet Cable x 1
- Telephone Cable x 1
- Quick Installation Guide x 1
Ports and indicators
Hardware connections
- Connect a fiber optic cable to the PON port.
- Connect a computer to the GE port using the Ethernet cable (optional).
- Connect a telephone to the TEL port using the PHONE cable (optional).
Wi-Fi connection
-
Using SSID
Use the SSID and Wireless Key on the device label to connect wireless to the device. On your smartphone or notebook, find this SSID. Enter the Wireless Key to connect. -
Using WPS
Press the WPS button on the device and the WPS indicator will blink. Then press the WPS button on the client. If the WPS method fails, use the SSID and wireless key to set up a WiFi connection.
Configure on the web
Configure the device on the web page according to the information on the device label. Open a web browser, enter the IP address, default User Name and Login Password, and then click Login.
Environment
| Items | Features |
|---|---|
| Operating Temperature | 0°C~40°C |
LED Indicator Explanation
| Name | State | Description |
|---|---|---|
| Power | On | The device has been turned on. |
| Of | The device has not been turned on. | |
| Internet | On | In Routing mode and WAN connection is up. |
| Blinking | Attempt to get an IP address. | |
| Of | No internet connection or the modem router is operating in Bridge mode. | |
| PON | On | The device has been registered. |
| Blinking | Optical signal is detected. | |
| Of | No optical signal is detected. | |
| LOS | Blinking | No optical signal is detected. |
| Of | Optical signal is detected. | |
| WIFI | On | Wi-Fi has been turned on. |
| Blinking | Wi-Fi data is being transmitted. | |
| Of | Wi-Fi has been shut down. | |
| TEL1- TEL2 | On | The VOIP server has been registered. |
| Blinking | The voice service is in use. | |
| Of | The VOIP server is not registered. | |
| WPS | On | The device is successfully connected through WPS function. |
| Blinking | The device is being connected through WPS function. | |
| Of | The WPS function is not enabled, or the device is successfully connected |
through WPS function.
LAN1-
LAN4| On| The LAN port is properly connected.
Blinking| Data are being transmitted.
Of| The LAN port is not connected.
LED Indicator Explanation
| Name | Explanation |
|---|---|
| RESET | Hold down for more than 5 seconds and release to restore the factory |
settings. When reset takes effect, all indicators are on for 1s and then off.
WPS| Hold down the button more than 5 seconds and release it to use the WPS
connect the device.
WLAN| Enable/disable wireless network.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- ncrease the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different rom that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Caution!
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Wall Mounting Template
How to Wall-mount
-
Mark the two bracket holes using a pencil (not included).
-
Fasten the screws to the wall on the bracket holes.
Hang the device on the screws.
Screw Size : M4 x 20mm
This type of mounting is not recommended
|
Size
|
Scale
|
Rev
---|---|---|---
A2
|
1:1
|
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>